|
| 1 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: Asbestos Cement sheet. |
| 2 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. 15.41 |
| 3 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead :15.14.1 Of sectional area 40 square centimetres andabove |
| 4 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :15.12.1 Of area 3 sq. metres and below |
| 5 | 15.56 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 6 | 20 mm cement plaster of mix : 13.3.1 1:4 (1 cement: 4 fine sand) |
| 7 | 13.91 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 8 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane anufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical arameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the anufacturer of membrane: 14.91.1 1 to 3 mm thick |
| 9 | Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.12.1.3 0.63 mm thick with zinc coating not less than 275 gm/ m² |
| 10 | Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 12.4.2 0.63 mm thick with zinc coating not less than 275 gm/m² |
| 11 | Float glass panes 9.7.7.1 4 mm thick glass pane (weight not less than 10kg/sqm). |
| 12 | \\"12.53 Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level,suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.\\" |
| 13 | Providing and fixing PVC Vinyl flooring 2 to 3 mm thickness including labour & material charges etc complete. |
| 14 | Provision for purchasing essential articles for residing security forces135 L Desert Air Cooler ,Body Material ABS ,Cooling Coverage Area 6500 sq ft,Motor Speed 1400 RPM |
| 15 | Provision for repair and replacement of Acs including Gas, Service, new parts etc completeSplit AC 2 tonne in building no. 1 ( gas filling and service ) |
| 16 | Window AC 1.5 tonne in building no. 1 (PCB , gas , sevice ) |
| 17 | Split AC 2 tone in building no.2 ( gas filling and service) |
| 18 | Window AC 1.5 tonne in building no. 2 (PCB , gas , sevice ) |
| 19 | Window AC 1.5 tonne in building no. 2 (Comressor ) |
| 20 | Painting with synthetic enamel paint of approved brand and manufacture of required colourto give an even shade :13.62.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint ofapproved brand and manufacture |
| 21 | \\"Renewing wooden beams in roofs including making good the holes in walls and painting with oil type wood preservative of approved brand and manufacture complete, including removal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. 14.16.1 Not exceeding 4.00 metres in length. 14.16.1.1 Sal wood beams\\" |
| 22 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).9.1.2 Sal wood |
| 23 | 9.20 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.2 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 24 | Provision of provising and fixing of galvanised mild steel material xpended material (XPM) JALI of 4mm thick silver in clour inluding fixing charges etc complete |
| 25 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1 40 mm thick with 20 mm nominal size stone aggregate |
| 26 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 12.21.1 In 75x75 mm deep chase |
| 27 | \\"13.46 Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)\\" |
| 28 | Stone work ashlar sunk or moulded or sunk and moulded upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : 7.20.1 Red sand stone |
| 29 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer. |
| 30 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes |
| 31 | Provision for providing and fixing of electrical articles required for toilet block near barrack 1 salimgadh , Red fort Delhi (a) PVC Batten 1\\" 6ft length [EACH] |
| 32 | (b) FLUSH PVC BOXES 12M [EACH] |
| 33 | (c) FLUSH PVC BOXES 8M [EACH] |
| 34 | (d )FLUSH PVC BOXES 6M [EACH] |
| 35 | (e)FLUSH PVC BOXES 4M [EACH] |
| 36 | (f)FLUSH PVC BOXES 3M [EACH] |
| 37 | (g) FLUSH PVC BOXES 2M [EACH] |
| 38 | \\"(i) Suntech 24 Way TPN 6 WAY SPN Metal White Double Door Distribution Board MCB Box \\" [EACH] |
| 39 | \\"(J) PVC Insulated 4 mm Single Core Flexible Copper Wires & Cables polycab /comptaon/hevells ( 90 Mtr)\\"\\"\\" [EACH] |
| 40 | \\"(k) PVC Insulated 2.5mm Single Core Flexible Copper Wires & Cables polycab /comptaon/hevells ( 90 Mtr)\\"\\"\\" [EACH] |
| 41 | \\"(l) \\"\\"PVC Insulated 1.5mm Single Core Flexible Copper Wires & Cables polycab /comptaon/hevells ( 90 Mtr)\\"\\"\\" [EACH] |
| 42 | \\"(m) PVC Insulated 1 mm Single Core Flexible Copper Wires & Cables polycab /comptaon/hevells ( 90 Mtr)\\"\\"\\" [EACH] |
| 43 | (n) Havells or equivalent 12 M Cover Plate [EACH] |
| 44 | (o) Havells or equivalent 8M H Cover Plate [EACH] |
| 45 | (q) Havells or equivalent 4M Cover Plate [EACH] |
| 46 | (r) Havells or equivalent 3 M Cover Plate [EACH] |
| 47 | (s) Havells or equivalent 2M Cover Plate [EACH] |
| 48 | (t) Polycarbonate Bulb Holder for Wall [EACH] |
| 49 | (u) Havells or equivalent Crabtree Athena 5 Step Fan Regulator - 2 Module [EACH] |
| 50 | (v) Havells or equivalent Crabtree Athena 6A Five Pin Socket [EACH] |
| 51 | (w) Havells or equivalent Crabtree Athena 6A One-Way Switch (White) [EACH] |
| 52 | (x) Havells or equivalent Crabtree Athena 6A-16A Three Pin Combined Shutter Socket [EACH] |
| 53 | (y) Havells or equivalent Crabtree Athena 16A One-Way Switch with Indicator (White) [EACH] |
| 54 | (z)Cableguard DWC HDPE Cable Duct Pipes 2\\"inch [RMT] |
| 55 | \\"(aa) Havells or equivalent 32A Single Pole MCB, Multi, Standard (HA-SPMCB32)\\" [EACH] |
| 56 | (bb) Earthing GI Wire 8 No. 4mm (per kg) (120m) [KG] |
| 57 | \\"(cc) Havells or equivalent Ventil Air DX 12 inch Exhaust Fan (Metal)\\" [EACH] |
| 58 | (dd) LED Tube Light 22 watt [EACH] |
| 59 | (ee) Labour charges for execution of work [EACH] |
| 60 | (ff) Aluminium Thimble 50MM [EACH] |
| 61 | (hh)false ceiling light 2x2 36wtt [EACH] |
| 62 | (ii) squar board [EACH] |
| 63 | (jj) ceiling rose [EACH] |
| 64 | (kk) tape [EACH] |
| 65 | (LL) steel wire [EACH] |
| 66 | (mm) flexble pipe 1 inch roll [EACH] |
| 67 | (nn) Patch Screw 1\\" ,2\\",1.5\\" [EACH] |
| 68 | (oo) gitti Nylon Wall Plug [EACH] |
| 69 | (pp) mcb 16A [EACH] |
| 70 | (qq) 40A DP [EACH] |
| 71 | (rr) 100A TPN [EACH] |
| 72 | (ss) 50 sq mm 4 core Aluminium Armoured Power Cable [RMT] |
| 73 | (tt) 10 sq mm 2 core Aluminium Armoured Power Cable [RMT] |
| 74 | Provision of providing and fixing of plumbing & snitary articles for toilet block near barrack 1 salimgadh , Red fort Delhi(a) CPVC waste pipe 90MM heavy gaige [RMT] |
| 75 | (b) CPVC Waste Pipe 110 MM heavy gaige [RMT] |
| 76 | (c ) CPVC Waste Pipe 150 MM heavy gauge [EACH] |
| 77 | connection pipe (2ft length ) [RMT] |
| 78 | (d) Washbasin Tap [EACH] |
| 79 | (e ) Angle wall Tap [EACH] |
| 80 | (f) Toilet jet/Hand Shower [EACH] |
| 81 | (g) Tap/Cock [EACH] |
| 82 | (h) Toilet roll holder [EACH] |
| 83 | (o) Labour charges for execution of work [EACH] |
| 84 | (p) CPVC pipe 25mm (10ft) [EACH] |
| 85 | (q) CPVC elbow 25mm [EACH] |
| 86 | (r ) CPVC Tee 25mm [EACH] |
| 87 | (s) Tank nipple 25mm [EACH] |
| 88 | (t) M Tee 25x25 [EACH] |
| 89 | F Tee 25x25 [EACH] |
| 90 | (U) CPVC SOCKET 25mm [EACH] |
| 91 | Plumbing valves 1\\" [EACH] |
| 92 | CPVC Unions [EACH] |
| 93 | Stainless Steel Urinal Spreader [EACH] |
| 94 | cistern tank 6-10ltr [EACH] |
| 95 | Reducer CPVC [EACH] |
| 96 | SOLVENT 500GM [EACH] |
| 97 | TEFLON TAPE [EACH] |
| 98 | water tank 3 layer 1000ltr [EACH] |
| 99 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required |
| 100 | Providing & fixing White vitreous china water closet squatting pan (Indian type) along with “S” or “P” trap including dismantling of old WC seat and “S” or “P” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge14.80.2 Orissa pattern W.C Pan of size 580x440 mm |
| 101 | Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) : 6.3.1 With F.P.S.(non modular) bricks |
| 102 | Disposal of Malba/Unserviceable Material by machanical transport in addition to lead of 1 kilometer up to the lead 15 Kilometer including loading, unloading, all lifts and dumping in approved Municipal dumping ground complete. Please Enable Macros to View BoQ information |
