|
| 1 | Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge In cement mortar |
| 2 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sidesand ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres All kinds of soil |
| 3 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) |
| 4 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills,fillets etcupto floor V level, including curing but excluding the cost of centring, shuttering and finishing with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 5 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 6 | Extra for brick work with common burnt clay bricks/ cement concrete bricks in superstructure above plinth level upto floor five level |
| 7 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Sal wood |
| 8 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cementconcrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 9 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws |
| 10 | Providing / fixing powder coated aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z- sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene felt etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C. P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer in charge (including glazing and paneling)for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required including all fittings complete 16 guage |
| 11 | 12mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 coarse sand) |
| 12 | Regrading terracing of mud phaska covered with tiles or bricks, in cement by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement: 3 fine sand), including replacing unserviceable tiles or bricks with new ones anddisposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded) within 50 meters lead. |
| 13 | Cost of new tiles @ 35 tiles/ sqm |
| 14 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design. In 75x75 mm deep chase. |
| 15 | Providing and fixing of 3mm thickness APP (Atactic Poly Propylene Polymer ) Superthermoly STP sheet polyester based sheet black finishing including coats of silver paint with cemented surface by following method cleaning the surface with wire brush to make the surface free from all loose particles, dust etc then repairing / making the corner fillets dips with pidicrete URP 301 or equivalent water proofing compound in cement and sand mortar 12mm to 18mm thick and with PCC 1:2:4 mix. (I) Applying with shalitex STP primer for bitumen membrane @ 0.40 ltr/sq. mt. (II) Mt. by the 3mm thickness APP superthermoly STP black sheets polyester based sheet black finishing manufacture (III) Cut 1\\" deep groove above the roof surface on the groove with polymer modified mortar (IV) in case of low height parapets, terminate APP superthormoly STP polyester sheets pver the parapet (V) for over lapping of joints, rub the polythylene side of membrane by wire brush, apply shali bond APP over the ribbed area, alow it to the tackly and then fix the bitumenious side of APP superthermolySTP sheet polyester with hot application (VI) for longitudinal and tranverse joint pverlaps of 75mm and 100mm respectively id desired. the vital physical and chemical paramater of the membrane shall as under:- Siftening ppoint of membrane not less them 150*c cold flexiblity shall be upto 0\\"c when tested in accordance with ASTM, joint strengh in longitudunal and transverse direction at 1223*c as 350/300N/5cm. Tear strenght in longitudinal and transverse direction as 60/80N in 3mm thick, the weight of roll (40KG for 1 mtr bt 10 mtrs) the laying of membrane shall be got done through the certified applicator. |
| 16 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm |
| 17 | Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of anysize as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 18 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete In colour such as White, Ivory, Grey, Fume Red Brown |
| 19 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, laid on 20 mm thick cement mortar 1:4 (1Cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete In colour such as White, Ivory, Grey, Fume Red Brown |
| 20 | Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cementmortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab over 0.5 sqm) |
| 21 | Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters lead With cement mortar 1:4 (1 cement : 4 fine sand) |
| 22 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 23 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete 2 mm thick |
| 24 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer |
| 25 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required,to achieve even shade and colour Two coats |
| 26 | Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) |
| 27 | Finishing walls with Acrylic smooth exterior paint of required shade Old work (two or more coats applied @ 1.67 liters/10sqm on existing cement paint surface) |
| 28 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work. |
| 29 | Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diametre |
| 30 | Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion (i) Single socketed pipes 75 mm diametre |
| 31 | Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 32 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 |
| 33 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 |
| 34 | Providing and fixing PTMT grating of approved quality and colour Circular type 125 mm nominal dia with 25mm waste hole |
| 35 | Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106gms. |
| 36 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, 78 mm wide and effective height of 88 mm, weighing not less than 190 gms. |
| 37 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm |
| 38 | Providing and fixing un plasticized P.V.C. connection pipe with PTMT nuts, collars and bush of approved quality and colour 15 mm nominal bore with 45 cm length. |
| 39 | Providing and fixing of 35 liter water heater Geyser of approved make Racold, Havells, Cropmton or equivalent make as directed by EIC. |
| 40 | Providing & Fixing of Exhaust fan of approved make like (Havells, Orient, Crompton) including all necessary fittings all complete Job. |
| 41 | Providing and fixingTank Nipple of approved quality, complete 20 mm nominal bore |
| 42 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 20 mm nominal bore |
| 43 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid. |
| 44 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manuallycontrolled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 45 | Supplying fixing installtion and commissioning of 1.00 HP water mortor of approved brand like Crompton Greaves, KSB or equivalen including all necessary fittings and connections complete. |
| 46 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank |
| 47 | Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete 250x16 mm |
| 48 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete |
| 49 | 100x10 mm |
| 50 | 200x10 mm |
| 51 | Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. |
| 52 | 125 mm |
| 53 | 100 mm |
| 54 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete |
| 55 | Engagement of labour skilled/ unskilled for various dismantling works like tacking of floors, damaged tiles, etc including stacking of serviceable material as directed by EIC and disposal of unserviceable material up to 50 mtr lead. |
| 56 | Labour |
| 57 | Carpenter |
| 58 | Providing and fixing of 1'-4\\" to 2’-0” deep kitchen cabnets/ Almirah of approved design & make including shutters, partitioning with 19mm thick (water proof) ply board of approved make and quality including back covering of 0.7mm thick water proof ply and fixing 1mm thick mica of approved colour and make over the frame and shutter, as around including cost of all fixtures i.e. glazing, locking arrangements, handle etc. as per the directions of site Engineer. (complete Job) |
| 59 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete |
| 60 | Renewing glass panes, with putty and nails wherever necessary including raking out old putty Float glass panes of thickness 4.0 mm(weight not less than10kg/sqm) |
| 61 | Carriage of material by mechanical transport including all loading / unloading complete |
| 62 | Sand Aveg. lead of 20 Km |
| 63 | Stone Aggrigate upto 40mm and above Aveg. lead of 20 Km |
| 64 | Stone Aggrigate below 40mm Aveg. lead of 20 Km |
| 65 | Bricks Aveg. lead of 20 Km |
| 66 | Providing and fixing of following types of switches, sockets, allied accessories including dismantling of existing switches and sockets with terminations as required Anchor/Legrand/GM/Crabtree or equivalent make |
| 67 | 16A switch only piano type |
| 68 | 16A socket only piano type |
| 69 | 6A switch only piano type |
| 70 | 6A socket only piano type |
| 71 | 6A switch socket combine with gang box piano type |
| 72 | 16A switch socket combine with gang box piano type |
| 73 | Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable with 1.5 sq.mm. FR PVC insulated copper conductor single core cable as earth wire etc in existing surface / recessed steel/medium class PVC conduit Finolex/Polycab/Havells/RR kabel/ Anchor/KEI or equivalent make |
| 74 | Group A |
| 75 | Group B |
| 76 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in existing surface/ recessed steel/ medium class PVC conduit as required Finolex/Polycab/Anchor/V-Guard/ Havells/RR kabel or equivalent make |
| 77 | 2 x 1.5 Sqmm |
| 78 | 2 x 2.5 Sqmm |
| 79 | 2x 4 sqmm |
| 80 | 2x6 sqmm |
| 81 | Providing and fixing of following type of MCB's/switch gear of L&T/Havells/Anchor/ Schnedier/indoasian Opti-Pro/Legrand or equivalent make of 10 KA or more capacity series including testing and necessary terminations. |
| 82 | 63 A SPN |
| 83 | 6A-32A MCB's |
| 84 | Providing and fixing of following MCB distribution boxes double door with inbuilt tinned copper heavy duty bus bars for earth, earth, and jumpers of proper current rattings Havells/Anchor/Indoasian/SSK/legrand/hager or equivalent make |
| 85 | 16 way MCB box |
| 86 | Providing and fixing of LED lights of following type Crompton/Phillips/Orient/Havells/Syska/Panasonic or equivalent make including necessary terminations as required. |
| 87 | 9 Watt LED Lamps |
| 88 | Providing and fixing of 48\\" Sweep ceiling fan with allied accessories complete including necessary terminations crompton/ Anchor/Orient/Usha or equivalent make. |
| 89 | Providing and fixing of fan dimmers of piano type Anchor/Legrand/GM/Crabtree or equivalent make. |
| 90 | Providing and fixing of Angle/straight holders including terminations GM/Havells/Krant /Anchor/Great white or equivalent make |
| 91 | Supplying and fixing of 20mm medium class PVC conduit along with accessories in surface including cutting the wall |
| 92 | Supplying and fixing of 25mm medium class PVC conduit along with accessories in surface including cutting the wall |
| 93 | Providing and fixing of Phenolic sheets of desired shapes and sizes incluting cutting, finishing, drilling etc. |
| 94 | Providing and fixing of exhaust 250/300mm including terminations as required Crompton/Havells/Orient or equivalent make Please Enable Macros to View BoQ information |
