|
| 1 | (25.1.1) Random rubble masonry with hard stone in foundation and plinth :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 2 | (32.2.2) Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 15 mm cement plaster on the rough side of single or half brick wall of mix : including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar 1:6 (1 cement : 6 fine/ coarse sand) |
| 3 | (32.35.1) Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20kg/ 10 sqm). |
| 4 | (9.3) Providing and laying lean cement concrete 1:4:8 in Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in concrete mixer, laid manually, compacted with surface vibrator, finishing and curing complete as per clause 601, 112 of MoRT&H specification including all material, labour, machinery, lighting, guarding and maintenance of diversion. |
| 5 | (32.50.1) Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work |
| 6 | (30.21.4) Chequered precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) Ordinary cement without any pigment. |
| 7 | CROSS TRAINERProviding and fixing of Cross trainer of size not less than 1140mm (Length) x 625mm (Width) x 1750mm. (Height), to enhance the mobility of upper and lower limbs and improve the flexibility of joints. The main structure frame shall be made from G.I. pipe minimum of 80NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The Handle Frame shall be made up of at least 25NB “C” Class G.I. Pipe. The footrests shall be made from LLDPE/Aluminum casting material of size not less than 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 Micron thicknesses complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in- charge to fulfill the functional requirement. |
| 8 | SEATED PULLERProviding and fixing of Seated Puller of size not less than 2400mm (Length) x 800mm (Width) x 2000mm. (Height), to enhance the strength of upper limbs and the muscles in chest and back and promote cardio-pulmonary function. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The handle frame shall be minimum of 32NB “C” class G.I. pipe. The seat frame minimum of 50NB “C” class G.I. pipe, Closing Caps shall be made up of LLDPE/high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 9 | CHEST PRESSProviding and fixing of Chest Press of size not less than 2200mm (Length) x 800mm (Width) x 2000mm. (Height), to enhance the strength of upper limbs and the muscles in chest & back and promote cardio pulmonary function. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The handle frame shall be made up from at least 32NB “C” class G.I. pipe. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size not less than 330mm X 300 mmX2mm thickness. Closing Caps shall be made up of LLDPE/high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 10 | DOUBLE STANDING TWISTERProviding and fixing of Double Twister Standing of size not less than 1500mm (Length) x 600mm (Width) x 1300mm. (Height), to enhance flexibility of waist. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The handle frame is minimum of 25NB shall be made from “C” class G.I. pipe. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of minimum size Ø250mm and 10mm thick. Closing Caps shall be made up of high quality LLDPE/Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in- charge to fulfill the functional requirement. |
| 11 | STANDING SEATING TWISTERProviding and fixing of Seating & Standing Twister of size not less than 1700mm (Length) x 540mm (Width) x 1250mm. (Height), to enhance flexibility of waist. Suitable for people of different ages except children. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The bottom frame of the Seating & Standing twister be at least of 32 NB, 50 NB, and 25 NB shall be made from “C” class G.I. pipe. The handle frame of Seating & Standing twister of minimum 25 NB & Foot resting frame of seating side shall be made from “C” class G.I. pipe minimum of 25mm NB. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of minimum size 250 mm diameters and 10mm thickness. Closing Caps shall be made up of high quality LLDPE/Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done by Pure Polyester powder of Ackzonoble/ Berger/ Nerolac Paint with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in- charge to fulfill the functional requirement. |
| 12 | SKY WALKER : Area : - 1.72 Mtr x 0.63 Mtr Safe Area :- 2.54 Mtr x 1 MtrProviding and fixing sky walker made from \\"B\\" class G.I. pipe. the main frame pipe is Ǿ 80mm made from \\"C\\" class G.I. pipe. the outer ring of sky walker is Ǿ 32mm made from \\"C\\" class G.I. pipe. for connecting the handle frame to main pipe Ǿ 60mm \\"C\\" class G.I. pipe is used. the bottom support of M.S. round plate of Ǿ 250mm x 10mm thickness is welded at bottom. the leg movement frame is of 50x50mmx2mm thick CRC square pipe. the handle frame is of Ǿ 40mm made from \\"C\\" class G.I. pipe. the foundation used for fixing is 80x40mmx3mm thickness C-channel. the footrests is made from aluminum casting material, its sizes are 130x310x5mm. closing caps made from top quality FRP material with 2mm thickness & plastic cap are used. the pins used are made up of Ǿ 25mm bright bar. the bearings used are \\"6205zz\\" & \\"6203zz\\" permanent lubricated sealed bering of reputed make (SKF/FAG). high tensile steel with galvanized nut bolts are used for assembly. the serclips used for assembly are of Ǿ 25mm. the powder coat is done by poly urethane & epoxy powder with 60 to 70 micron thickness |
| 13 | SIT UP BOARD DOUBLEProviding and fixing of Sit up Board double of size not less than 1580mm (Length) x 1400mm (Width) x 680mm (Height), to enhance the flexibility of whole body. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The remaining frame of the sit up board minimum of 32mm NB shall be made from “C” class GI pipe. The powder coating shall be done with Pure Polyester powder Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 14 | SURFING BOARDProviding and fixing of Surfing Board of size not less than 1150mm (Length) x 900mm (Width) x 1400mm (Height), to build up the muscle groups of the waist, enhance the body coordination and flexibility. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The footrests shall be made from high quality LLDPE/fiber reinforced plastic material. High tensile steel with galvanized nut bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powder of Ackzonoble/ Berger/ Nerolac with minimum 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 15 | LEG PRESS : Area :- 0.40x1.77 MtrSafe Area :- Providing and the center pThe bottom support thickness is welded the remaining outer frame pipe. the foundation used for Ǿ 80mm made from \\"C\\" c & 10 mm thickness, 25mmx25mm. to join the c 3mm thicness is used. the seats are size 330mmx3mm and size 250mmx 200mm. the footrests is made 130mmx311.77 mtr.-1x2.38mtr. fixing leg press made from \\"B\\" class G.I. p pipe is of Ǿ 115mm made from \\"C\\" class G.I. of M.S. round plate of Ǿ 250mm & at bottom. is of Ǿ 40mm made from \\"C\\" class G.I. foundation fixing is consist of three equal class G.I. pipe, M.S. round p x 3mm M.S. angle. centre pipe & outer frame seamless pipe of thickness fitted on the outer frame is made up of FRP material of 300mm of thickness 3mm & M.S. plate of is used to support it. from aluminum casting material, i 10mm & 5mm thickness. pipe, made pipe and 250mm, 10mm items i.e. plate of Ǿ 250mm angle. Ǿ 120mm & thickness 5 support its sizes are the frame of footrests consists of Ǿ 32mm made from \\"C\\" class G.I. pipe. closing caps made from top quality FRP material which is of 2 mm thickness. the inner bushes is made from seamless pipe, its diameter is 60mm & 5mm thickness. the pins used in are made up of Ǿ 25 mm hardened bright bar, the bearings used are of \\"6205zz\\" permanent lubricated sealed bearing of reputed make (FAG/SKF). the handles used are of rubber grip. high tensile steel with galvanized nut bolts are used for assembly. the serclips used for assembly are of Ǿ 25 mm. the powder coat is done by poly urethane & exoxy powder with 60-to-70-micron thickness. |
| 16 | Double Arch Swing: In this two children can enjoy the swing at one time.The arch shaped side frame is made of 65mm NB 'B' Class GI pipe and top pipe is made up of 50mm NB 'B' Class G.I. pipe.The frame is powder coated to give an aesthetic look.The swing is made up of 5mm thick anti skid canvas top. The rubber belt seat is suspended on 6mm rubber coated GI chain. The ball bearings shall be mounted inside a specially designed nylon clamp. |
| 17 | FRP wave slide :Providing and Fixing of FRP wave slide its required area 4.6 mtr x 0.9 mtr platform height should be 5' Ground Level and should be made by 32 mm NB and 25 NB and 20 mm NB pipe MS pipe.Slide length10' all components paint by PU paint in multi colours |
| 18 | DoubleSeeSaw: Providing and fixing of double see saw of height 0.5 mtr from ground level.Seat frame and base should be made with 50 mm NB ‘B’ Class G.I. Pipe. Handle pipe should be 25 mm NB ‘B’ class G.I.pipe.Length of see saw lever should be 6 feet. Seats are made with FRP/LLDPE. Max. 4 children can play at one time. Please Enable Macros to View BoQ information |
