|
| 1 | Demolition of PCC in ground floors & pavings n exc 15 cm thickness (below or above ground level) (unreinforced) complete all as specified and directed. |
| 2 | M&L for brick work with fly ash bricks old size, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed. |
| 3 | M&L for brick work with fly ash bricks old size, straight or curved on plan exc 6m mean radius, in half brick walls built in cement mortar 1:4 complete all as specified and directed. |
| 4 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and as directed. |
| 5 | Taking down cement plaster on brick or stone wall etc. including racking out joints hacking for key scrubbing down with water etc complete all as specified and as directed. |
| 6 | M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed.Note :- WPC will measuered and paid separatly under relevant item of schedule. |
| 7 | Supply only WPC, complete all as specified and as directed. |
| 8 | Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over and including a coat of 1.0 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified. |
| 9 | M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces, finished fair and even on walls in cement mortar (1:6), complete all as specified. |
| 10 | Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.0 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified and directed. |
| 11 | M&L for rendering 5mm thick on fair faces of ceiling / chajja concrete surfaces in cement mortar 1:3 complete all as specified & directed. |
| 12 | M&L for prepartion of newly plastered ceiling/chajja surfaces and applying three coat of white wash complete all as specified and directed. |
| 13 | Taking down chowkat or frames exc 1.5 sqm but n exc 4.0 sqm each with shutter (without taking off shutters from the frame) and removing to or from store complete all as specified and as directed. |
| 14 | Taking down Chowkats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) and removing to or from store complete all as specified and as directed. |
| 15 | M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50X100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directed. |
| 16 | M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50X125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directed. |
| 17 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) complete all as specified and as directed. |
| 18 | S&F factory made 30 mm thick single extruded WPC (Wood Polymer Composite) wire gauzed i.e. panel shutter will be wire mesh in lieu WPC , the wire gauze shall be warped on additional square 8mm MS Solid tube and this tube shall be welded to MS frame complete all as specified and as directed. |
| 19 | S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed. |
| 20 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet trip of 20mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and directed. |
| 21 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 22 | Providing and fixing factory made uPVC white colour fixed window,area not exceeding 1.00sqm each made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Net opening will be measured for payment purpose.) |
| 23 | S&F 100 mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22,complete all as specified and directed. |
| 24 | S&F 75 mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21,complete all as specified and directed. |
| 25 | S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed. |
| 26 | S&F aluminium anodised 75 mm barrel tower bolts of extruded section complete all as specified and directed. |
| 27 | S&F 150 mm long extruded aluminium alloy handles,fabricated type, anodised complete all as specified and directed. |
| 28 | S&F 100 mm long extruded aluminium alloy handles,fabricated type, anodised complete all as specified and directed. |
| 29 | S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 30 | S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 31 | S&F Hasp and staple,75 mm long, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and as directed. |
| 32 | S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed, complete all as specified and as directed. |
| 33 | S&F Floor door stopper of brass body 140 mm and tongue, anodised, with hard drawn steel spring & end rubber shoes, fixed in floor, complete all as specified and as directed. |
| 34 | M&L for 4mm thick figured glass, pin head type and glazing with oil putty in square n. exc 0.5 sqm in each pan for bathrooms/toilets ventilators all as directed |
| 35 | M&L for 4mm thick,ordinary quality and glazing with oil putty in square n. exc 0.5 sqm in each pan for bathrooms/toilets ventilators complete all as specified and directed. |
| 36 | M&L for 4mm thick,ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pan for bathrooms/toilets ventilators all as directed. |
| 37 | M&L for 100 mm thick cement concrete Type B-1, 1:2:4 (using 20 mm graded stone aggregate) as in sub bases with nominal reinforcement complete all as specified and directed. |
| 38 | M&L Mild steel TMT bars 6mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 39 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 40 | M&L Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm in floors laid over 15mm thick 1:6 cement mortar screed bed etc. set and jointed in neat cement slurry and pointed in white of coloured cement to match complete all as specified and directed. |
| 41 | M&L Non Skid ceramic coloured tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors/skirting etc. laid over 15mm thick 1:6 cement mortar screed bed set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 42 | M&L Glazed ceramic coloured tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match all complete all as specified and directed. |
| 43 | M&L for Rendering 10 mm thick in CM 1:4 finished even and fair on vertical surfaces on wall to receive wall tiles,complete all as specified and directed. |
| 44 | S&F Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 conforming to Fe-290, Gde-E-165 the grill shall be inseted in the wall surface including necessary drilling and grouting with cement etc, complete all as specified and directed. |
| 45 | M&L Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 46 | S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290, Gde-E-165 the grill shall be inseted in the wall surface including necessary drilling and grouting with cement etc, complete all as specified and directed. |
| 47 | Dismanting of wrought iron or mild steel work af any description not otherwise provided for complete all as specified and as directed by Engineer-in-charge |
| 48 | M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of Red oxide zinc chrome primer zinc chrome complete all as specified and as directed. |
| 49 | M & L for demolition of Concrete (RCC) of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 50 | M&L for RCC 1:1.5:3 type A1 (20 mm graded crushed stone aggregate) nominal mix as in chajja complete all as specified and directed. |
| 51 | M&L for RCC 1:1.5:3 type A1 (20 mm graded crushed stone aggregate) nominal mix as in slab supported on wall complete all as specified and directed. |
| 52 | M&L for use and waste of fair finish formwork to sides of chullah hoods, chajjas complete all as specified and directed. |
| 53 | M&L for RCC 1:1.5:3 type A1 (20 mm graded crushed stone aggregate) nominal mix as in Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like complete all as specified and directed. |
| 54 | M&L for use and waste of fair finish formwork for sofits of slab complete all as specified and directed. |
| 55 | M&L for RCC (1:1.5:3) type A1 (nominal mix)(using 20mm graded crushed stone aggregate) coloumn, pillars, piers, posts and struts complete all as spd and directed. |
| 56 | M&L for RCC 1:1.5:3 type A1 (20 mm graded crushed stone aggregate) nominal mix in beams, cantilevers, bressummers, lintels over1.5 m span complete all as specified and directed. |
| 57 | M&L for use and waste of fair finish formwork for coloums complete all as specified and directed. |
| 58 | M&L for use and waste of formwork for sides and sofits of beams and lintels complete all as specified and directed. |
| 59 | M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 60 | M&L Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 61 | M&L for use and waste of fair finish Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. |
| 62 | M&L for use and waste of fair finish Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide complete all as specified and directed. |
| 63 | M&L for prepartion of old surface and applying two coats of Super Latex (Sika or equivalent) @ 80gm per sqm per coat in the ratio of 1:1.5:5 (latex : water : cement) over internal/external of brick/concrete surface after cleaning and washing the surface by wire brush and plenty of water The entire surface shall be washed throughly with plenty of water and then allowed to dry complete all as specified and as directed. Note:- The entire process to be executed through authorised applicator. |
| 64 | M&L Machine cut kota stone slab flooring 16mm thick over cement screed laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed. |
| 65 | M&L Kota stone slab 16mm thick in riser of steps, skirting, dado & pillar over plaster & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed. |
| 66 | M&L green Marble work 16 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Makrana Adanga complete all as specified and as directed. |
| 67 | M&L for 16 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including screed bed of 20mm thick in 1:4 cement mortar, complete all as specified and as directed. |
| 68 | M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified |
| 69 | M&L Plain Cement Concrete 1:3:6 type C1 (using 20 mm stone aggregate) as in surface channels and drains, complete all as specified and directed. |
| 70 | S&F in repairs 15 mm bore Stop valve fancy type, chromium plated with long shank and cup concealed type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed. |
| 71 | S&F in repairs Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for pipe complete all as specified and as directed. |
| 72 | S&F in repair CP Bib taps 15mm dia, with cfancy handle, screwed down, screwed for iron pipe or for brass ferrule, fency type and fixed complete all as specified and directed. |
| 73 | S&F in repair Stop valve cast copper alloy screwed down high pressure with capston headed handle chromium plated concealed type screwed both ends for pipe 15 mm bore or for unions complete all as specified and as directed. |
| 74 | S&F in repaie fancy,chromium plated Stop valves 15mm dia, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. |
| 75 | S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and as directed. CAT No: PIS-10 Make : Prayag |
| 76 | S&F in repair chromium plated 15mm central hole basin mixer single lever without popup waste system with 450mm long braided hoses complete all as specified and as directed. |
| 77 | S&F in repair wall mounted mixer for Bathroom, made of brass, chrome polish finish, without hand shower, complete all as specified and as directed. |
| 78 | S&F in repair stainless steel kitchen plate rack(24''x24''x10'') including necessary fixing/fitting & making good the existing surface complete all as specified and directed . |
| 79 | S&F in repairs Door seal (Snake guard) with Aluminium frame powder coated complete all specified and directed. |
| 80 | S&F in repair soap dish, any type fixed to plugs chromium plated brass screws complete all as specified and as directed. |
| 81 | S&F in repair glass self assembly consisting of 5.5 mm thick glass sheet glass self 12 Cm wide with CP bracket gaurd and railing 60 Cm long complete all as specified and as directed. |
| 82 | S&F in repair chromiuim plated Swivel shower roses with shower arm, 125 mm size including fxing to steel pipe or union etc complete all as specified and as directed. |
| 83 | S & F in repairs vitreous china squatting pan, 'Orissa\\" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing , connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. |
| 84 | S&F in repairs PVC valveless,syphonic action type, low level PVC flushing cistren 10 ltr cap white with flush pipe & all fitting complete all as specified. |
| 85 | Supply & Fixing in repairs Vitreous China Ware Wash hand basin white flat back size 550mmx400mm without pedestal, cutting for and pinning ends of brackets or erecting stand including necessary PVC outlet pipe, CP coupling 32mm dia complete all as specified complete all as specified |
| 86 | S&F PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and as directed. |
| 87 | S&F in repairs 32mm dia Waste coupling, brass , chromium plated for glazed ware , basins , etc. with long screwed shanks and fly -nuts , flange end bedded in red lead cement and other end fixed complete all as specified and as directed. |
| 88 | S&F in repairs 40mm dia Waste coupling, brass , chromium plated for glazed ware ,Sink basins , etc. with long screwed shanks and fly -nuts , flange end bedded in red lead cement and other end fixed complete all as specified and as directed. |
| 89 | S&F in repairs kitchen sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, coupling including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx460mm bowl size 410 mmx330mmx 160mm etc complete all as specified and as directed. |
| 90 | S&F in repairs grating square, Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified and directed. |
| 91 | Taking up or down 15mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 92 | Taking up or down 20mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 93 | S&F 16 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 94 | S&F 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 95 | S&F in repair Vitreous China wash basin, white, flat back, size 450x300mm excluding Taps but including brackets including cutting for pinning in ends of brackets,complete all as specified and directed. |
| 96 | S&F in repairTubular towel rail, 20mm dia, D type, brass chromium plated, 60cm long between flanges complete all as specified and directed. |
| 97 | Supply & fix mirror 600mmx 400mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 98 | S&F PVC plain bend (any radius) for 75 mm bore, PVC pipes, complete all as specified and directed. |
| 99 | S&F 75mm bore PVC (SWR) junction single, (single T) equal or unequal fitted with oval access door, complete all as specified and directed. |
| 100 | S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including dismantling old unserviceable existing pipe with fittings, complete all as specified and directed.[Note : Payment shall be made in net length as fixed between the fittings as per SSR Part-II preamble para (a) of Page 384.] |
| 101 | S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including dismantling old unserviceable existing pipe with fittings, complete all as specified and directed. |
| 102 | S&F PVC (SWR) bends, plain, 110 mm bore any radius, complete all as specified and directed. |
| 103 | S&F 110 mm bore PVC (SWR) junction single (single T) equal or unequal fitted with oval access door, complete all as specified and directed. |
| 104 | Supply and fixing as in repair 75mm dia PVC pipe fixed to wall or laid in trenches set in cement mortar with and including MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc complete all as specified and directed. |
| 105 | S&F in repair PVC door bends with oval access door (any radius) for 75 mm bore PVC pipes, complete all as specified and as directed. |
| 106 | S&F in repair PVC door bends with oval access door (any radius) for 75 mm bore PVC pipes, complete all as specified and as directed. |
| 107 | Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing and making good of groves for concealed GI tube, cutting not exc 10cm girth complete all as specified and as directed. |
| 108 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, granite/kota stone and other similar situations incl polishing, complete all as specified and directed. |
| 109 | S&F 18/19 mm thick, lead free PVC board Superior quality of density not less than 0.55 g/cm3 as in moduler shutters/cabimet drawer cupboard cabinet shutter including all frame work as specified and directed by Engr-in-Charge |
| 110 | M&L for PVC lipping over PVC Sheet, with necessary fittings, complete all as specified and directed. |
| 111 | S&F in repair soft closing 'O' Degree high grade mild steel bright finish or electro galvanised for cup board shutter complete all as specified and as directed. |
| 112 | S&F in repair magnetic catcher for kitchen cabinet shutter as approved by Engr-In-Charge. |
| 113 | M & L for (a) providing and laying water proofing treatment of sunken portion of WCs, bathroom etc by applying cement slurry with acrylic based modified cementitaous composite compound coating of make as approved in technical instruction 5/2003 (b) First layer of slurry of cement @ 0.5 Kg/Sqm mixed with acrylic based polymer modified cementatious composite compounds @ 0.250 Kg/Sqm. This layer will be allowed to air cure for 4 hours. (c) second slurry of cement @ 0.500 Kg/Sqm mixed with acrylic based polymer modified cementatious composite compounds @ 0.250 Kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (d) 200 micron thick polythene film pasted with the help of bituminous adhesive shall be provided over treatment. includingTesting of all trap & joint and sunken slab shall be done as per IS-1742 & report to be submitted to Engr-in-Charge for claiming of payment. |
| 114 | S&F in repairs MS dropery rod of 25mm dia of PVC coated in curtain rod, complete all as specified and directed. |
| 115 | S&F in repairs MS PVC sheeted/powder coated bracket size 150mm made to shape suitable for holding curtain/drapery rod of 25mm dia fixed with PVC rail plugs and MS steel screws for single/double rods, complete all as specified and directed. |
| 116 | S&F for multipurpose lock 12mm to 25mm thick panel, for cupboard, cabinet, with brass srews, brass keys fixed to cabinet/cupboard, complete all as specified and directed. |
| 117 | S&F for Brass Handle for cupboard/cabinet, fixed with SS screws, complete all as specified and directed. |
| 118 | M&L for repair to crack portion with jacktting technique, taking down existing plaster upto brick wall surface of min 200 mm wide, cleaning to loose particles on surface of brick work along the length of crack and filling the gap/ crack area with PCC 1:1.5:3 type A0 using 12.5mm aggregate both side of the wall surface fixed with, drilling holes 10mm dia on either side of the crack by means of drilling machine through out the full width of the wall @25 cm c/c and insert 8/10 mm dia od in the drilled holes, welded with horizontal rod to with hold the welded mesh and applying grit plaster 1:1:2 using 4 mm and down aggregate finished even and smooth without using extra cement, complete all as specified and directed. (Note: Reinforcement and welded mesh will be measured and paid separately) |
| 119 | Taking down carefully aluminium/Copper conductor point wiring (light , fan, socket or powr) complete including fittings such as switches, ceiling rose, pendents, regulators sockets etc and removing (except those to be reused shall be kept in safe custody at the site) and making good disturbed surfaces of walls, floors etc tomatch with the existing completeall as specified and directed. Please Enable Macros to View BoQ information |
| 120 | Taking down carefully aluminium/Copper conductor point wiring (light , fan, socket or powr) complete including fittings such as switches, ceiling rose, pendents, regulators sockets etc and removing (except those to be reused shall be kept in safe custody at the site) and making good disturbed surfaces of walls, floors etc tomatch with the existing completeall as specified and directed. Please Enable Macros to View BoQ information |
