|
| 1 | Dismantling of Plain or corrugated semi corrugated, etc sheets in roof coverings including ridges etc complete all as specified and as directed . |
| 2 | S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed. |
| 3 | S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering/ cladding to wall fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed. |
| 4 | Making good under cills over arches, lintel and bresummers,including all pinning when necessary with using cement mortar (1:6) complete all as specified and directed. |
| 5 | S&F in repairs PVC board designer Eaves 9 to 15 mm thick elegant appearance not less than 200mm of width complete all as specified and directed. |
| 6 | Dismantling structural steel work of any description not otherwise provided for etc complete all as specified and as directed . |
| 7 | S&F mild steel rolled sections [Fe 410-W (Gde E-250) quality - A] as in roof trusses (framed), trussed, main and cross beams, hip and jack rafters, purlins, Gusset plate and base plates, where connected to common rafters and running rails, distance pieces, cleats, guides for sliding doors; fixed with angle cleats or other connecting plates, framing for cladding, staging for water tanks, nuts, bolts, washers etc,includng welding or riveting etc, complete all as specified and as directed. |
| 8 | M&L for the Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed. |
| 9 | S&F anodised aluminium snap grid of size 605x605mm frame work for false ceiling hangers 4mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out GI flat iron 40x3mm size 60mm long and fixed expansion hold fasteners 12.5mm dia and 40mm long,complete all as specified and as directed. |
| 10 | S & F 4mm thick Non-asbestos fibre cement decorative/designer building boards to steel frame work with screws in ceiling (flat and/or slopping) and including jointless finish with & also including joining compound and tape as per manufacturer instructions, plaster of paris, 1mm thick over Non AC board ceiling and applying one coat of OBD over a coat of primer,including dismantling of wall and ceiling boards complete all as specified and as directed.Notes :- (i) The board shall be confirming to IS-14862 and shall be manufactured from the homogeneous mixture of cement, quartz and cellulose and shall be cued with high pressure steam using auto claving process.(ii) Aluminium frame work shall be measured and paid for separately. |
| 11 | Providing and fixing PVC FALSE CEILING, consisting of 6mm (+0.25) thick hollow board plain ambossed PVC sheet of manufactured by ISO 9001-2008, certified company, used fixed with Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. complete as specified by manufacturer & drawing and directed by Engr-in- Charge. |
| 12 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 13 | M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed. |
| 14 | M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in vertical Surface etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 10mm thick screed bed in CM (1:4), complete all as specified and as directed. |
| 15 | M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed. |
| 16 | M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM (1:4), complete all as specified and and as directed. |
| 17 | M&L Vitrified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM (1:6), complete all as specified and as directed. |
| 18 | Providing and fixing PVC WALL PANEL, consisting of 6mm (+0.25) thick hollow board plain ambossed PVC sheet of manufactured by ISO 9001-2008, certified company, used fixed with Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. complete as specified by manufacturer & drawing and directed by Engr-in- Charge. |
| 19 | Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and as directed. |
| 20 | M&L for granite (of any type) 18-20mm thick (Table rubbled and mirror polished ) in steps, jambs, pillars, window-cills, cooking platform etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 20mm thick screed bed in CM (1:6), complete all as specified and directed. |
| 21 | Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, disposing off the retrieved debris outsite the premises, complete all as specified and as directed. |
| 22 | Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, disposing off the debris outsite the premises, complete all as specified and as directed. |
| 23 | S&F factory made 1.25 mm thick pressed steel frame of size 165 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after preparation of the surfaces, complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 24 | S&F factory made 1.25 mm thick pressed steel frame of size 165 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after preparation of the surfaces, complete all as specified and as directed. Please Enable Macros to View BoQ information |
