|
| 1 | Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 2 | Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume) |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size) |
| 4 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concrete |
| 6 | providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.(b) 12mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}) |
| 7 | providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. (c) 16mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}) |
| 8 | Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 9 | Providing and fixing 1 8 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1 : 4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm |
| 10 | Providing edge moulding to 1 8 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work |
| 11 | Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. |
| 12 | Construction of median and Island above road level with approved material brought from borrow pits, spread, sloped and compacted as per clause 408 |
| 13 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment). |
| 14 | Supply at site of work well decayed farm yard manure, from any available source, approved by the engineer in charge including screening and stacking. |
| 15 | Spreading of sludge farm yard manure or/and good earth in required thickness (cost of sludge, farm yard manure or/and good earth to be paid for separately). |
| 16 | Grassing with ' Doobs' Grass Grassing with 'Doobs' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for moving including supplying good earth if needed. In rows 7.5 cm apart in either direction |
| 17 | Maintenance of Lawns with Fine Grassing for the First Year Maintenance of lawns with fine grassing for the first year including watering etc |
| 18 | Supplying and fixing Mild Steel Bollards, fabricated from 168 mm diameter, 4 mm thick M.S. pipe, having a total height of 1000 mm with 600 mm above ground and 400 mm embedded below ground, the embedded portion to be grouted in cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate, 20 mm nominal size) in a pit of size 300 mm × 300 mm × 450 mm deep, including excavation in bituminous/concrete pavement as required, ensuring proper alignment, grinding smooth, and finishing the exposed portion with alternate bands of black and yellow synthetic enamel paint with reflective additive, applied over one coat of red-oxide zinc-chromate primer, complete as per drawing and as directed by the Engineer-in-Charge. |
| 19 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 108kg @ per sqm |
| 20 | 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1 : 5 (1 cement : 5 coarse sand), including pointing withcement mortar 1 : 2 (1 cement: 2 stone dust) with an admixture of pigment to match the shade of stone. Red sand stone |
| 21 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1 : 4 (1 cement: 4 coarse sand). Light shade pigment using white cement |
| 22 | Providing, fabricating, supplying, and fixing a central decorative flower-type structure made of metal/alloy as per the approved design, drawings, and reference image. The structure shall be crafted using high-quality, weather-resistant materials, with smooth finishing and protective coating to prevent corrosion and fading. The work shall include internal supporting framework, base plate, and anchoring arrangement, securely fixed to a reinforced concrete foundation/plinth with appropriate anchor bolts and non-shrink grout.The rate shall be inclusive of all materials, tools, labor, transportation, safe handling, lifting, placement, and final alignment, complete in all respects as directed by the Engineer-in-Charge. |
| 23 | Providing and fixing bolts including nuts and washers complete. |
| 24 | Structural steel work riveted, bolted or welded in built up sections, trussesand framed work, including cutting, hoisting, fixing in position and applyinga priming coat of approved steel primer all complete. |
| 25 | Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concree, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with allk lifts and lead of 1000 metres Dismantling Brick/ tile work In cement mortar |
| 26 | Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concree, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with allk lifts and lead of 1000 metres Steel work in all types of sections upto a height of 5m above plinth level excluding cutting of rivet. Excluding dismembering |
| 27 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm |
| 28 | Dismantling kerb stone by manual means and disposal of dismantled material with all lifts and up to a lead of 1000 metres |
| 29 | Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting In position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. |
| 30 | Painting Two Coats on New Concrete Surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces) |
| 31 | Dismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 metres, stacking serviceable and unserviceable materials separately By Manual means Bituminous courses |
| 32 | Cable Duct Across the Road (Providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road (new construction), extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of RCC pipe as per IRC:98-1997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC: 98 - 1997 and approved drawings.) Single row for one utility service |
| 33 | Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. |
| 34 | Providing and laying bituminous macadam with higher capacity hot mix plant using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction. |
| 35 | Solar Powered Road Marker (Solar Stud) Supplying of Solar Raised Pavement Markers made of polycarbonate molded body with circular shape, solar powered, LED self illumination in active mode 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode.The marker shall support a load of 20000 kg tested in accordance to ASTM D 4280.The marker should be resistant to dust and water ingress according to IP 65 standards and should withstand temperatures in the range of 0 C to 70 C. Color of lighting could be provided in red or yellow (amber) as per requirement and typical frequency of blinkikng in 1 Hz.There should be current losses of less than 20 microamperes at 2.4 V in sleepcharging mode to enhace the life of the marker and a full charge should provide for a minimum autonomy of 50 hours.The height, width and length of the marker shall not be less than 10mmx100mmx100 mm. Also, the surface diameter of the marker shall not be less than 100 mm respectively.The weight of the marker shall not exceed 0.5 Kilograms.Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive and complete as directed by the engineer.) |
| 36 | Painting Lines, Dashes, Arrows etc on Roads in Two Coats on New Work (Painting lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control ) Over 10 cm in width |
| 37 | Painting Lines, Dashes, Arrows etc on Roads in Two Coats on New Work (Painting lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control ) Up to 10 cm in width |
| 38 | Supply, fabrication, and fixing of Mild Steel bollards made from 100 mm diameter, 4 mm thick MS pipe, total height 1000 mm, top end plain, finished with polymer paint in approved color, and provided with two reflective tape bands, 50 mm wide each. Bollards to be fixed by drilling holes in reinforced or plain cement concrete using a power-driven drill machine to a depth of 100 mm, with 10 mm dia × 100 mm steel bolts and washers grouted using approved epoxy resin anchor, ensuring proper alignment. Complete in all respects as per drawing and directions of the Engineer-in-Charge. |
| 39 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class-B Type IV retro reflective sheeting fixed cover 2 mm thick aluminium sheeting vide clause 801.3, 3mm/4mm thick aluminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67. 90 cm equilateral triangle (for caution) |
| 40 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class-B Type IV retro reflective sheeting fixed cover 2 mm thick aluminium sheeting vide clause 801.3, 3mm/4mm thick aluminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67. 90 cm circular (for speed limit) |
| 41 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class-B Type IV retro reflective sheeting fixed cover 2 mm thick aluminium sheeting vide clause 801.3, 3mm/4mm thick aluminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67. 90 cm x 75 cm rectangular (advance direction) |
| 42 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class-B Type IV retro reflective sheeting fixed cover 2 mm thick aluminium sheeting vide clause 801.3, 3mm/4mm thick aluminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67. 80 cm x 60 cm rectangular (exit direction) |
| 43 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class-B Type IV retro reflective sheeting fixed cover 2 mm thick aluminium sheeting vide clause 801.3, 3mm/4mm thick aluminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67. 60 cm x 60 cm square (Round about Name) |
| 44 | Supply and installation of green wall system including fabrication and fixing of MS frame made of rectangular MS pipe (2”x1” and 2”x2”) with proper supports, welded or grouted as required, painted with primer and two coats of paint to prevent corrosion; complete drip irrigation system of approved make (Jain Irrigation) with accessories such as end cap, bend, tee, socket, 12 mm and 16 mm lateral pipes, 4 & 8 LPH drippers, and water filter; supply and installation of vertical garden units comprising PVC frames and pots (frame size 7”x21” for 3 pots) with drip irrigation arrangement, including transportation and shifting of materials to site, fixing of frames and pots, supply of engineered pot mixture (cocopeat, sand, soil, immunity boosters, manure, charcoal powder, micro-nutrients, etc.) and filling of pots, plantation of natural indoor plants (Money Plant, Oxicardium, Philodendron, Peperomia, Red Congo, Syngonium, Berkin, Xanadu, Ferns, etc.) and outdoor plants (Syngonium, Pandanus, Sprengeri, Ficus, Rhoeo, Setcretia, Ophiopogon, Alternanthera, Dracaena, Zade, Chlorophytum, etc.), all complete for a fully functional and sustainable green wall system as per specification and direction of Engineer-in-Charge. |
| 45 | Heavy duty,armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. 2c x 10 mm2 1.1kV |
| 46 | Earthing with copper earth plate 600mmx600mmx3m thick including accessories ,and providin, masonry enclose with copper plate having locking arrangemen and watering pipe etc. Iwith charcole or coke and salt as required. |
| 47 | Providing and fixing 25mmx5mm cpper earth strip in 0.5Mtr below ground as strip earth electrode,including soldering as required. |
| 48 | S/L 8 SWG G.I. wire in ground :- Supplying and laying 8 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required. |
| 49 | Providing , laying and fixing following dia GI pipe (medium Class) in ground complete with G.I.Fittings including trenching (75 cm deep) and refilling etc. as required. 40 mm dia |
| 50 | Providing , laying and fixing following dia GI pipe (medium Class) in ground complete with G.I.Fittings including trenching (75 cm deep) and refilling etc. as required. 65 mm dia |
| 51 | S.I.T.C of following rating approved make LED Bollard fitting with cylindrical shape and inverted cone shape head of height 600 to 850mm power input-8/9watt with die cast aluminium housing opel with PC diffuser, IP:65/54 protection, conferming to IS:10322 part 5 etc all complete as required. (excluding plinth charge) |
| 52 | S.I.T.C of floowing rating LED Flood lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 1C[.Z70Y AC,50Hz. Luminarie shall be confirm tolS:,1,0322part-5/section-5 and shall be complete with all neccssary accessories as required50/60 WATT LED Flood Light |
| 53 | Design, fabrication, supply and delivery of 9.0 mtr high decorative Wing Pole made of MS pipe with 3.0 mm wall thickness, comprising 150 mm Ø base pole, 75 mm Ø wing poles on both sides, 50x50 mm MS box section bracket for street lamp mounting, and 600x1200 mm advertisement frame in MS box section, with provision for fixing of luminaire (street light not included in this item), decorative laser cut stainless steel elements as per approved architectural design, complete with base plate, welding, grinding, surface preparation, one coat primer and two coats of epoxy paint of approved shade, including all materials, labour, tools, transport and incidental works as per approved design and drawing. |
| 54 | ).5m Double Arm suitbale for 90mm Top(Basic Rate : Rs. 1380.00 + Overhead & profit @ 14.95% = Rs. 1586.31 ) |
| 55 | Installation, Testing & Commissioning of the 9 Mtr. Octagonal Pole & light fitting with the help of suitable tools and plants, wiring of luminaires with all materials and construction of shallow foundation with M25 grade concrete considering safe soil bearing capacity of 10T/mtrs sq. (Basic Rate : Rs. 8100.00 + Overhead & profit @ 14.95% = Rs. 6207.30 ) |
| 56 | S/F 6 amps to 32 amps rating 240 volts, ‘C’ series miniature circuit breaker suritable for lighting and other loads of following poles in the existing MCB DB complete with connection, testing and commissioning etc. as reqd.6/32 amps,Single pole |
| 57 | SITC of following rating LED street lighting luminari with pressure die cast housing and toughtend glass cover ,IP 66 protection,lumonous EFFICARY>=110 LM/W with lens in existing pole/pipe for supply voltage 100-270 V AC,50 Hz.Luminarie shall be confirm to IS:10322 part 5/section 3 and shall be complete with all necessery accessories as reqquired.120W LED street light |
| 58 | Supplying and drawing following size of FR PVC insulated copper conductor single core cable in existing surface/recessed steel/PVC conduit including dismantling as required 3x1.5 sqmm |
| 59 | Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 4 core x16 sq mm (Basic Rate: Rs. 221.00 + Overhead & Profit @ 14.95% = Rs. 254.03) |
| 60 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required; 4 X 16 sq. mm (28mm) |
| 61 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 35 sq mm direct in ground including excavation, cushioning, protective coveringand and refilling the trench etc. as required |
| 62 | Supplying and laying of 40mm dia medium class GI pipes for road crossing (Basic Rate: Rs. 300.00 + Overhead & Profit @ 14.95% = Rs. 344.85) |
| 63 | Earthing with GI earth pipe 4.5 mtr long,40 mm dia including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required. |
| 64 | Supplying and laying 6 SWG GI wire at 0.50 meter below ground level for conductor earth electrode, including soldering etc as reqd. |
| 65 | S.I.T.C of Outdoor stand mounted feeder peelar with 63 amps TP&N,MCB incomer ,65 amps TP contractor automatic switch of luminaries,power tool control incommer outgoing terminal etc as required. (Basic Rate: Rs. 27800.00+ Overhead & Profit @ 14.95% = Rs. 31956.10) Please Enable Macros to View BoQ information |
| 66 | S.I.T.C of Outdoor stand mounted feeder peelar with 63 amps TP&N,MCB incomer ,65 amps TP contractor automatic switch of luminaries,power tool control incommer outgoing terminal etc as required. (Basic Rate: Rs. 27800.00+ Overhead & Profit @ 14.95% = Rs. 31956.10) Please Enable Macros to View BoQ information |
