|
| 1 | M&L for APP based modified pre fabricated five layer 3 mm thick and weighing not less than 3.6 Kg/Sqm water proofing membrane reinforced with polyester non woven fabric mat with 150 gm/Sqm black finished with compatible primer conforming to IS 3488 @ 0.40 Lit/ Sqm and bonding material 85/25 bitumen 1.2 Kg/Sqm before laying membrane laid by torch application side overlap of 75 mm and over lap of 100 mm longitudinally, At the junction of roof and parapet wall a grove of 75mm wide and 65mm deep and shaping horizontal of groove with 1:3 with bituminous mastic joints/overlap shall be sealed with hot bitumen 85/25 and applying one coat of aluminium paint on top of the membrane (at any height ) complete all as specified and as directed. |
| 2 | M&L for providing plain cement concrete (1:2:4) type B1 using 20mm grade agg. as in coping including weathering slightly, rounded or chamfered angles and throating and necessary use and waste of form work complete all as specified and as directed. |
| 3 | Dismantling structural steel work including, rafter , Purlin , doors , gate but excluding framed trusses etc complete all as specified and as directed. |
| 4 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed. |
| 5 | Dismantling floor or wall tiling of any description and size including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and as directed. |
| 6 | Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc including cleaning off premises where directed complete all as specified and as directed. |
| 7 | M&L for roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe 410-W(Gde-E-250) quality-A complete all as specified and as directed. |
| 8 | Excavating in post holes (or similar holes) each n exc 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in hard/dense soil complete all as specified and as directed. |
| 9 | M&L for cement concrete type D2, (1:4:8) (Using 40mm graded granite stone aggregate) in foundation filling and mass concrete complete all as specified and as directed. |
| 10 | M&L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces including preparation complete all as specified and as directed. |
| 11 | M&L for preparing old painted surfaces of steel and iron surfaces over 10 cm in width or girth by cleaning, sand papering, brushing with wire brushes, scrapping by steel scrappers etc and applying one coat of synthetic enamel paint to give an even and smooth surface having no sign of brush marks complete all as specified and as directed. |
| 12 | M&L for Composite PUF roof Panel between PPGI sheets 0.50mm thick hot dipped galvanized sheet (total coated thickness 0.54mm on both side with 50/40mm thick layer of rigid CFC free closed cell polyurethane foam (Density 40kg +/- 2 kg/cum) insulated sandwiched panel ( one side Mangalore pattern corrugated PPGI sheet and other side plain PPGI sheet). The panels shall be provided with cam lock system for interlocking. The PUF panel sandwiched between PPGI sheet have fire retarding and including all necessary fittings complete all as specified and as directed. |
| 13 | M&L for Composite PUF wall Panel between PPGL sheets 0.50mm thick hot dipped galvanized sheet (total coated thickness 0.54mm on both side with 50/40mm thick layer of rigid CFC free closed cell polyurethane foam (Density 40kg +/- 2 kg/cum) insulated sandwiched panel ( both side plain PPGL sheet). The panels shall be provided with cam lock system for interlocking. The PUF panel sandwiched between PPGL sheet have fire retarding and including all necessary fittings complete all as specified and as directed. |
| 14 | Taking down cement plaster on brick or stone walls etc including raking out joints,hacking for key ,scrubbing down with water etc complete all as specified and as directed. |
| 15 | Demolition of unreinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including cleaning off premises where directed complete all as specified and as directed. |
| 16 | Demolition of brick / block masonry / Stone masonry built in Cement mortar complete all as specified and as directed. |
| 17 | M&L for precast cement concrete (1:3:6) type C-1 (Using 20mm graded aggregate ) block masonry with solid blocks exc10 cm thick in width and setting in cement mortar (1:6) complete in wall complete all as specified and as directed. |
| 18 | Taking down chowkhats or frames not exc 1.5 sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed. |
| 19 | Taking down chowkhats or frames exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames) complete all as specified and as directed. |
| 20 | M&L for Joint free non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in flooring etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile laid etc complete all as specified and as directed. |
| 21 | M&L for coloured Glazed ceramic joint free tiles as in vertical surface of Size 450x350x7 mm set and jointed in neat cement slurry laid etc complete all as specified and as directed. |
| 22 | M&L for vitrified ceramic tiles light shed 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm (size 600 x 600), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed. |
| 23 | M&L for double charged vitrified coloured tiles light shade 8-10 mm thick (square/ rectangular) polished, area of each tile exceeding 0.36 sqm but not exceeding 1.00 sqm in floors etc, set and jointed in neat cement slurry and pointed with colour cement to match the tile laid etc complete all as specified and as directed. |
| 24 | Ditto all as per item No 23 above but in skirting/vertical surface etc complete all as specified and as directed. |
| 25 | M&L for 20 mm thick screed bed or bedding layer in C:M (1:6) for laying floor tiles complete all as specified and as directed. |
| 26 | M&L for 15 mm thick screed bed or bedding layer in C:M (1:6) for laying floor tiles complete all as specified and as directed. |
| 27 | M&L for 10 mm thick rendering in C:M (1:4) on vertical surfaces for receiving wall tiles complete all as specified and as directed. |
| 28 | M&L for 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in sub base etc complete all as specified and as directed. |
| 29 | M&L for 20(+ -2mm) thick Granite (of jet black ) work (table rubbed and polished ) in steps ,jambs ,pillars,window cills, cooking platforms and like in over 20mm thick cement mortar (1:6) for screed bed including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including Moulding to Exposed edges complete all as specified and as directed. |
| 30 | M&L for providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed. |
| 31 | M&L for machine cut superior quality Kota stone slab flooring 20-25 mm thick over cement screed , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete match including bulnosed to edges complete and incl 20 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and as directed. |
| 32 | M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed, incl 10mm thick rendering in CM (1:4) on vertical surface for receiving complete all as specified and as directed. |
| 33 | M&L for 15 mm thick cement plaster on brick or concrete surface in cement mortar1:6 included finishing surface even and smooth without using extra cement on walls etc complete all as specified and as directed. |
| 34 | M&L for preparation of new plastered surfaces of walls and applying two coats of luster paint over one coat of alkali resistant priming etc complete all as specified and as directed. |
| 35 | M&L for applying a thick layer of wall care putty on wall to achieve even and smooth surface complete all as specified and as directed. |
| 36 | M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over one coat of alkali resistant priming paint etc. complete all as specified and as directed. |
| 37 | M& L for complete removal of existing treatment of old ceiling surfaces and applying a thick layer of wall care putty over prepared plastered surface to receive the surface even and smooth and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of approved manufacturer of required shade and colour complete over a coat of wall primer as per manufacturer's specification complete all as specified and as directed. |
| 38 | All as per item No 37 above but for Ceiling surface complete all as specified and as directed. |
| 39 | M&L for providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile with wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Doortransmission gear made of mild steel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass complete all as specified and as directed. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 40 | S&F 5.50mm thick selected quality plain or grounded or frosted glass in squares in exc 0.5 sq.m in each pane including solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers fixing with rubber beading or PVC gasket etc complete all as specified and as directed. |
| 41 | S&F Door closer hydraulically regulated,designation No. 2,universal type, aluminium (Die cast) body suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed etc. complete all as specified and as directed. |
| 42 | Dismantling of Wall panel and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and including re-fixing in position complete all as specified and as directed. |
| 43 | M&L for providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions false ceiling including sunk or raised moulding pattern approved by GE fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish including necessary supporting hanger with 4.0 mm dia GI wire and 'J' bolts washer nuts for securing frame work to Gl frame work for (605 mm x 605 mm) seamless ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre incl thin layer of putty with gypsum binder, sanding the surface till smooth surface is obtained and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed. |
| 44 | M&L for First class soft wood Moulding sectional area of exc 13 sqcm but n exc 25 sqcm as in cornices, picture rails and the like fixed with screws complete all as specified and as directed. |
| 45 | M&L for 12 mm thick Plywood, type BB, fixed with screws to timber frame work plywood, grade 1 (with BWR resin) with with min 5 Nos ply; fixed for wall panelling and ceiling including all fittings fixture as per drawing at site etc complete all as specified and as directed. |
| 46 | M&L for decorative Veneer 3 mm to 4 mm thick type 1 of surface finish with PU polishing (colour and pattern as approved by GE) fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed. |
| 47 | M&L for Plain fillets/Cornice (Pattern /shape approved by GE) square, rectangular or triangular in section exc 6 & n.Exc 13 Sq.cm, clean sawn, secured with nails or brads etc complete all as specified and as directed. |
| 48 | M&L for Plain fillets./Cornice (Pattern /shape approved by GE) square, rectangular or triangular in section exc 13 & n.Exc 25 Sq.cm, clean sawn, secured with nails or brads etc complete all as specified and as directed. |
| 49 | M&L for preparation New wooden surfaces as in wooden doors, window and wall panelling etc ,sanding the surfaces using sanding machine, application of pigment and hardener to desired colour and finally applying one or more coats of melamine polish with spray guns, compressor etc complete till glossy surface is obtained complete all as specified and as directed. |
| 50 | S& F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade). calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge). minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fasV lugs or SS dash fasteners shall be paid for separately). Note: for WPC solid door/window frames, minus 5mm tolerance in dimension ,i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directed. |
| 51 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain Panelled door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and as directed. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 52 | S&F 100mm butt hinges cold rolled mild steel medium weight and fixed complete all as specified and as directed. |
| 53 | S&F 100mm Aluminium handles, cast type, anodised complete all as specified and as directed. |
| 54 | S&F for Aluminium anodised, barrel tower bolts 150mm long of ex- truded section and fixed complete all as specified and as directed. |
| 55 | S&F 300 mm long aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections complete all as specified and as directed. |
| 56 | S&F 300 mm long aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections complete all as specified and as directed. |
