|
| 1 | Demolition of cement concrete (un reinforced) in ground floors and paving n.exc 15cm thickness (below or above ground (level) and lowering if necessary, removal of the rubbish off the premises complete all as specified and directed. |
| 2 | Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and removing serviceable tiles to store yard and rubbish off the primises complete all as specified and directed. |
| 3 | Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and as directed. |
| 4 | Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed. |
| 5 | Dismantaling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed. |
| 6 | Dismantling wall and ceiling board of any descrition complete all as specified and directed. |
| 7 | M&L for rolling and consolidating road formation surfaces in cutting with 8 to 12 tonne power roller complete all as spd and directed. |
| 8 | M&L for pavings, with mix of fly ash, clinker & stone dust in the proportion of 1:3:6 (ie 10% fly ash, 30% clinker and 60% stone dust ) laying in layers n. exc 10cm thick, watering, ramming and compacted with hand/power roller 8 to 12 tonn roller to required camber and gradient complete all as directed by Engineer-in-Charge. |
| 9 | M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled layers not exceeding 15 cm thick, watered and rammed with 8 to 12 tonne power roller to a true surface complete all as specified and directed. |
| 10 | M & L for PCC (1:3:6) Type D2 using 40 mm graded aggregate used as in sub base floor/pavings and finishing complete all as specified and as directed. |
| 11 | M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed. |
| 12 | M&L TMT mild steel bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9 mm `dia or securing with clips quality conforming to complete all as specified. |
| 13 | Welding in repairs exc 2.5cm but n exc 5cm in length with thickness of metal to be welded exc. 20mm but n.exc 25mm for windows and ventilators complete all as specified and directed. |
| 14 | S & F Roof trusses (framed) of angle iron members trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed. |
| 15 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed |
| 16 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified any height Mtr height including all necessary scaffolding and safety measures complete all as specified and directed |
| 17 | M & L 75 mm thick cement concrete type C2, for PCC (1:3:6) using 40 mm graded aggregate as in sub base and pavings etc finishing cement concrete surface without using extra cement complete all as specified and as directed. |
| 18 | M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified |
| 19 | M&L vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed. |
| 20 | M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exc. 0.18 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed. |
| 21 | M&L for Glazed ceramic tiles Coloured 450 x 300mm 7 to 8 mm thick in wall/dado etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match rendering over 10 mm thick in CM 1:3 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed. |
| 22 | M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite of any type of work. |
| 23 | Material and labour for 25 mm thick chequered cement concrete tiles of size 30x30x25 mm mm,set ,jointed and pointed using with grey cement and pigment in floors, pavings etc including the setting and jointing in neat cement plaster or slurry 0.3 kg/sqm over 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as per specification. |
| 24 | M&L for pre-polished colour factory made machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete all as specified and directed |
| 25 | M&L for refixing of old machine pressed precast concrete interlocking paver block of any shape and size with grey cement and pigment complete all as specified and directed |
| 26 | M&LProviding and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified as directed. |
| 27 | M&L for preparing existing old machine-pressed precast concrete interlocking paver block surfaces. thorough cleaning by steel wire brushing and sandpapering, scraping down smoke, soot, moulds, moss, and efflorescent salts. Treatment of oil and greasy spots with appropriate chemical degreasers as required. Surface must be made dust-free and dry before applying two coats of Low VOC Acrylic Lacquer Polish/Coating (VOC content < 50 g/L) to achieve a uniform high-gloss \\"wet look\\" finish. All work to be completed as per manufacturer specifications and directed by the Engineer-in-Charge. |
| 28 | M&L for preparation of concrete kerb stone or plaster surface of any description not otherwise described over 10cm width or girth and applying two coat of water based floor coat paint emulsion over one coat of self priming coat emulsion by diluting with 30% to 40% water complete all as specified and directed by Engr-in-Charge. |
| 29 | S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long complete all as specified |
| 30 | S&F aluminium snap grid frame work for false ceiling complete all as spd and directed. |
| 31 | S&F 4mm thick non asbestos fibre cement designer building boards fixed or laid on aluminium frame/grid with screws, complete all as spd and directed. |
| 32 | S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified. |
| 33 | S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified. |
| 34 | Taking down chowkats or frames exc 1.5 sqm but n. exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as spd and directed |
| 35 | S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples. |
| 36 | M&L 4mm thick ACP board (Aluminium composite panel), exterior grade, (approved colour) fixed with aluminium tapperd clip to aluminium frame work all as specified and as directed. |
| 37 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 38 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, locking arrangement ,C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 39 | M&L sheet glass 4.8 mm thick ordinary quality and glazing with oil putty and pin in square exc 0.50 sqm in each pan complete as directed. |
| 40 | S&F 4mm thick sheet glass, ordinary quality and glazing with rubber gasket & aluminium beading in square n. exc 0.5 Sqm in each pane, complete all as specified and directed. |
| 41 | S&F in repair aluminium (extruded section body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as spd and directed. |
| 42 | S&F 100 mm long butt hinges, stain less steel with galvanised mild steel hinge pin, anodised and fixed , type B-21 complete all as specified and directed. |
| 43 | S&F for 150 mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 44 | S&F in repair MS drapery rods of 25 mm dia of PVC coated as in curtain rods complete all as spd and directed. |
| 45 | S & F MS PVC sheeted/power coated bracket size 150 mm made to shape suitable for holding curtain/drapery of rod of 25mm dia fixed with PVC rawl plugs and MS steel screws complete all as directed by Engr-in-Charge . |
| 46 | Taking down cement plaster of any description from brick wall surfaces etc including racking out joints and hacking for key, scrubbing down with water etc complete all as directed. |
| 47 | M&L Rendering 15 mm thick cement plaster in CM 1:4 on other than fair faces of brick/concrete surfaces finished fair and even and complete all as specified and directed. |
| 48 | M&L for prepration of new plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 49 | M&L for complete removal of existing treatment by means of mechanical scrubing and dust collector machine and by hand where mechanically cannot reach and washing down with water and applying exterior wall putty on the surface to bring the surface smooth and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces complete all as specified. |
| 50 | M&L for two coat of synthetic enamel paint on old steel pre painted PUF Shelter surfaces including preparation of surface of any description, over 10 cm in width or girth not other wise described by spray guns operated mechanically by expert painter for smooth finishing and also cleaning the rooms all as specified and directed by Engr-in-Charge. |
| 51 | S & F in repairs vitreous china squatting pan, 'Orissa\\" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing , connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. |
| 52 | S&F in repair vitreous China wash basin white, flat back,size 550X450 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as spd and as directed. |
| 53 | S&Fin repairs Vitreous China Urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe) bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified. |
| 54 | S&F in repairs 10 litre capacity PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete (with brackets). Make- Hindware, Parryware |
| 55 | S&F in repair 15mm bore fancy type stop valve , chromium plated concealed type cast copper alloy, screwed down , high pressure , with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed |
| 56 | S&F in repair PVC connection 15mm size PTMT nuts of length 600mm complete all as specified. |
| 57 | S&F in repair 15mm bore pillar taps cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed sunk and fly nuts complete all as specified. |
| 58 | S&F as in repair bib taps cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule |
| 59 | S & F in repair waste coupling of PTMT (half or full threaded) 32mm bore dia of discharge pipe complete all as specified and as directed. |
| 60 | S&F as in grating square 150mm size of PTMT(minimum 100 gms) complete all as specified and directed. |
| 61 | S & F in repair 600 X 450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board for commercial plywood fixed to wooden plugs with chromium plated brass screws and cups complete all as specified. |
| 62 | S&F as in repair tubular towel rail brass chromium plated 20 mm dia `D' type 60 cm long between flanges complete all as spd and directed. |
| 63 | S&F as in repair chromium plated shower roses 125 mm long with or without swivel joints, any size, including fixing fixing to steel pipe or union complete all as specified and direceted. |
| 64 | Taking up or down steel tubing and connection including cleaning for refixing or removed to store,15 mm dia bore complete all as specified and directed. |
| 65 | S&F for 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings ( plane and brass threaded) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 66 | Dismantling of cast iron 100 mm dia pipes jointed in cement mortar complete all as specified and directed. |
| 67 | Dismantling of cast iron 75mm dia pipes jointed in cement mortar complete all as specified and directed. |
| 68 | S&F PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wall with steel clamps all as specified and directed . Make : Supreme/ Finolex. |
| 69 | S&F PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint , laid in trenches or in floors complete all as specified and directed. |
| 70 | S&F PVC SWR bends of 100 mm bore complete all as specified and directed. |
| 71 | S&F PVC SWR bends of 75 mm bore complete all as specified and directed. |
| 72 | S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 110 mm dia complete all as specified and directed. |
| 73 | S&F PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and directed. |
| 74 | S&F 15 mm bore angle valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed. Please Enable Macros to View BoQ information |
