|
| 1 | Taking down chowkhat or frame with shutters n.exe 1.50 Sqm (without taking of shutter from frame ) each complete all as specified and directed |
| 2 | Taking down chowkhat or frame with shutters exe 1.50 Sqm and not 4 sqm (without taking of shutter from frame) each complete all as specified and directed |
| 3 | Dismaltaling of plain or corrugated steel sheeting , any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed. |
| 4 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed |
| 5 | Hacking Out Old Broken Glass (any thickness, size, quality or description) from Wooden Frames, Glazed with Putty or fixed with Beads, complete all as specified and as directed. |
| 6 | S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm each panes complete all as specified. |
| 7 | M&L old size brick work with fly ash bricks straight or curved on plan exc 6 m mean radius build in CM 1:6 including demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc completet all as specified |
| 8 | Demolition of RCC ( other then ground floor )piller, beams landing, chajjas slabs sleves & similar suspended work.and removing unserviceable material exc 100 mtr as specified. |
| 9 | M&L for RCC (1:1.5:3) type A1 (nominal mix)(using 20mm graded crushed stone aggregate) coloumn, pillars, piers, posts and struts complete all as spd and directed |
| 10 | M&L for mild steel TMT bar 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for column, hooking end binding with binding wire and including mild steel wire(annealed) not less than 0.9mm dia complete all as specified & directed by Engineer in Charge. |
| 11 | S&F TMT reinforcement bar, conforming to Fe-500, 5mm dia and upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as binding with and including mild steel wire (Annealed) not less than 0.9mm dia or securing with clips all as specified. |
| 12 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 122 x 54 mm & sash 47 x 64 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 13 | S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows and other frames/chowkhat of size 50x100 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade ), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS scews having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (face) and 1100N (Edge), minimum compressive strength of 58 N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in -Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately) Note :- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile demension on plus side shall be acceptable but no extra payment on this account shall be made. |
| 14 | S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows and other frames/chowkhat of size 50x125 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade ), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS scews having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (face) and 1100N (Edge), minimum compressive strength of 58 N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in -Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately) Note :- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile demension on plus side shall be acceptable but no extra payment on this account shall be made. |
| 15 | S&F for factory made single extruded WPC (wood polymer composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws , all as per direction of Engineer-in -Charge. Note :- Stainless steel butt hinges and necessary SS Screws shall be paid separately) |
| 16 | S&F for 35mm thick factory made single extruded WPC (wood polymer composite) solid wire gauzed i.e. panel will be of wire gauze in lieu of panel. The comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws , all as per direction of Engineer-in -Charge. Note :- Stainless steel butt hinges and necessary SS Screws shall be paid separately) |
| 17 | S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples. |
| 18 | S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. |
| 19 | S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and directed. |
| 20 | M&L sheet glass 4.8 mm thick ordinary quality and glazing with oil putty and pin in square n. exc 0.50 sqm in each pan complete as directed. |
| 21 | M&L 4mm thick ACP board (Aluminium composite panel), exterior grade, (approved colour) fixed with aluminium tapperd clip to aluminium frame work all as specified and as directed. |
| 22 | S & F stainless steel Butt hinges100mm long medium weight ,cold rolled complete as specified . |
| 23 | S&F 75mm long butt hinges, extruded alluminium alloy/stain less steel with galvanised mild steel hinge pin, anodised and fixed , type C-21 complete all as specified and directed. |
| 24 | S&F aluminium anodised 150 mm barrel tower bolts of extruded section all as specified and directed. |
| 25 | S&F aluminium anodised 75 mm barrel tower bolts of extruded section all as specified and directed. |
| 26 | S&F 150 mm long aluminium alloy handles,fabricated type, anodised all as specified and directed. |
| 27 | S&F 75 mm long aluminium alloy handles,fabricated type, anodised all as specified and directed. |
| 28 | S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and dirceted. |
| 29 | Dismantling wall and ceiling board of any descrition complete all as specified and directed. |
| 30 | S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long complete all as specified |
| 31 | S & F powder coated aluminium snap grid frame work of size of grid 605 x 605mm for false ceiling all as specified. |
| 32 | S&F in repair for 6mm thick non asbestos fibre cement designer building boards fixed or laid on aluminium frame/grid with screws, complete all as specified and directed. |
| 33 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including Aluminium snap beading for glazing/ paneling, all complete as per architectural drawings and the directions of Engr-in-Charge all as specified and directed. |
| 34 | S&F for Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 35 | S&F in repair harrison curtain rails, mild steel, chromium plated with conical end balls suitable for fixing as end of curtain/dropery rods complete all as spd and directed |
| 36 | Demolition of concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removal of rubbish off the site complete all as specified and directed |
| 37 | M&L for PCC type D2, 1:4:8 using 40mm graded aggregate in foundations, filling and mass concrete all as specified and directed. |
| 38 | M&L for Sand filling under floors or in foundations including watering and consolidation all as specified and directed. |
| 39 | M&L for Machine pressed precast concrete interlocking paver block any shape and size, pre-polished confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and pigment complete as specified all as specified and directed. |
| 40 | Dismantling structural steel work in- cluding doors, gates but excluding framed truss etc all as specified and directed. |
| 41 | S & F roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. Fe-410-W (Gde-E-250) quality-B |
| 42 | S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete as specified and directed. |
| 43 | M&L for PCC 1:2:4 type B 1 using (20 mm graded aggregate) as in lintels upto 1.5m clear span, cills, blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering slightly rounded or chamfered angles and throating all as specified and direct. |
| 44 | Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and removing serviceable tiles to store yard and rubbish off the primises as directed |
| 45 | M&L for 25 mm thick PCC 1:2:4 type B-0 (Using 12.5mm graded crushed stone aggregate) as in floor, finished the surfaces fair & even to receive floor finishes, complete all as specified and directed. |
| 46 | M&L Non Skid coloured ceramic tiles 10 mm thick (Square/rectangular) area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed. |
| 47 | M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tiles exc. 0.06 sqm but n. exc 0.11 sqm of approved colour as in floors etc set and joined in neat cement slurry over 15mm thick sreed bed of cement mortar (1:6) complete all as specified and directed. |
| 48 | M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm thick set and jointed in neat cement slurry over back coat of layer of 10 mm thick with cement mortar 1:4 and pointed in white or colour cement to match the colour of tiles complete all as speciified and directed. |
| 49 | M&L for 18mm to 20mm thick green marble (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm thick screed bed CM(1:6) complete all as spd and directed |
| 50 | Taking down cement plaster of any description from brick wall surfaces etc including racking out joints and hacking for key, scrubbing down with water etc complete all as directed. |
| 51 | M&L Rendering 15 mm thick cement plaster in CM 1:6 on fair faces of brick/concrete work surfaces finished fair and even complete all as specified and directed.. |
| 52 | M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed.Note :- WPC will measuered and paid separatly under relevant item of schedule. |
| 53 | Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.0 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified . . |
| 54 | M&L for prepration of new plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 55 | Material & Labour for complete removal of existing treatment, preparation of surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.0 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified . . |
| 56 | Complete removal of existing treatment and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over plastered surfaces of walls to prepare the surface even and smooth complete all as specified . . |
| 57 | M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of Red oxide zinc chrome primer zinc chrome complete all as specified and as directed. |
| 58 | M&L preparation of old surfaces of steel of any description over 10cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as spd and directed. |
| 59 | M&L for Preparation of old wooden surfaces and applying one coats of synthetic enamel paint complete all as spd and directed. |
| 60 | S & F in repairs vitreous china wash down water closet (pedestal pattern), white including thermoplastic seats and covers of grade 2 type, flat with hinging device of bronze or brass with nickel chromium plating, fixing bolt, connector to flush pipe and making connections to flush pipe, connector to branch soil pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. |
| 61 | S&F of PVC 'S' Traps of size 110mm dia complete all as directed. |
| 62 | Supply & fix in repairs vitreous china wash basin, white, flat back, size, 550X400mm including bracket for fixing 32 mm waste coupling complete all as specifid and direted. |
| 63 | S&F in repairs 10 litre capacity PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete (with brackets). Make- Hindware, Parryware, incl flush pipe of plyethene of low or high density of PVC 32mm dia for low level cistern all as specified and directed. |
| 64 | S&F as in repair chromium plated shower roses 125 mm long with or without swivel joints, any size, including fixing fixing to steel pipe or union complete all as specified and direceted. |
| 65 | S&F PVC waste pipe 32mm dia for wash basin 01 mtr to 3 mtr as per requirement basis all as specified and directed. |
| 66 | S&F in repair PVC waste pipe 32mm dia for wash basin 01 mtr to 3 mtr as per requirement basis all as specified and directed. |
| 67 | S&F in repair PVC waste pipe 40mm dia for sink 01 mtr to 3 mtr as per requirement basis all as specified and directed. |
| 68 | S&F in repair 32 mm bore Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm45gms/40mm-60 gms) |
| 69 | S&F in repair 40 mm bore Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm45gms/40mm-60 gms) for sink compelte all as spd and directed. |
| 70 | S&F in repair for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified |
| 71 | Supply and fix in repair for Gun metal gate valve,15 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed. |
| 72 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed. |
| 73 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed |
| 74 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified any height Mtr height including all necessary scaffolding and safety measures complete all as specified and directed |
| 75 | S&F in repairs PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wall with steel clamps all as specified and directed . |
| 76 | S&F in repairs PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 77 | S&F PVC SWR bends of 110 mm bore all as specified and directed. |
| 78 | S&F PVC SWR bends of 75 mm bore and all as specified and directed. |
| 79 | S&F in repair 15mm bore dia brass CP mixer for mixing hot &cold water screwed down for iron pipe and fixed complete all as specified |
| 80 | S&F for Solid PVC Wall Lining consisting of 5mm thick single side prelam colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame icl dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as spd and directed. |
| 81 | S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.complete all as spd and directed. (Make- Rajshree) and all as specified and directed. |
| 82 | Supply and fix in repair bib taps of 15mm bore fancy type, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule complete all as specified and directed. |
| 83 | S&F in repair 15mm bore fancy type stop valve/angle valve , chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed and all as specified and directed. |
| 84 | S&F in repair 15mm bore fancy type stop valve/angle valve, chromium plated concealed type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed and all as specified and directed. |
| 85 | S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160 mm and all as specified and directed. |
| 86 | Supply and fix in repair Pillar taps, 15mm bore, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'HOT or COLD' with long scrwed shanks and fly-nuts, screwed for iron pipe or for connection pipe complete complete all as specified and directed. |
| 87 | S&F in repair PVC connection 15 mm size PTMT nuts of length ength 450 mm complete all as specified and directed |
| 88 | S&F 16 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 89 | S&F 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 90 | Dismantling post (Wood/Steel or RCC) any section including taking out embedded portion in concrete, brick work , masonry etc, and making good disturbed portion complete all as specified and directed |
| 91 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed |
| 92 | Demolition for brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, facings, dressed stonework and precast concrete articles and removal or rubbish off the site complete all as specified and directed. |
| 93 | Excavating in trenches , n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier hole, laying of cables, pipes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in any kind of soilNote : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding and all as specified and directed. |
| 94 | M&L for pavings, with mix of fly ash, clinker & stone dust in the proportion of 1:3:6 (ie 10% fly ash, 30% clinker and 60% stone dust ) laying in layers n. exc 10cm thick, watering, ramming and compacted with hand/power roller 8 to 12 tonn roller to required camber and gradient complete all as directed by Engineer-in-Charge. |
| 95 | M&L Hardcore with broken stone/boulders of gauge n exc. 63mm, deposited, spread and leveliled in layers n exc. 150mm thick, watered and rammed to a true surface and all as specified and directed. |
| 96 | M&L for PCC type D2, 1:4:8 using 40mm graded aggregate in foundations, filling and mass concrete and all as specified and directed. |
| 97 | M&L, Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete, all as specified and as directed. |
| 98 | Supply only Liquid water proofing compound and all as specified and directed. |
| 99 | M&L for preparation on new plastered surface of wall, chajja, parapet etc and applying two coats of cement base paint over one coat of alkali resistant primer etc complete all as specified and as directed. |
| 100 | Supply only PVC coated Galvanised iron wire using Hot Dip technology chain electrogalvanised coating chain link fencing wire mesh of size 50mmx50mm minimum dia meter of wire 3 mm confirming to IS -2712-2003 havinga tensile strength 400 to 500 Mpa and and PVC coated to achieve outer dia. not less than 4 mm , straining bolts, etc. including provission of binding wireThe mesh wire a of the fabric shall be manufactured from ISI marked galvanised steel confirming to IS - 280:2006 (4th revision).The Kuncled ends should be of at least 50% of the sixe of the square mesh. The wires used in fencing should be long lasting and resistance to corrosion and testing criteria fullfill the requirement as per IS 1161:1998 complete all as specified and directed. |
| 101 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire and all as specified and directed.Note : Chain link fencing will be paid separately. |
| 102 | S&F posts and struts in fencing, railing etc including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 and all as specified and directed. |
| 103 | S&F Framed work such as grills, gratings, or in Flat iron etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc. |
| 104 | S&F mild steel screw bolts (machine made)with hexagonal or square heads at one end and screw other and each screw end to be fixed with washers and nut exc 5 cm but n.exc 10 cm long complete all as specified and directed |
| 105 | S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or in weep holes etc complete all as specified and as directed by Engineer-in-Charge. |
| 106 | Returning, filling in and including spreading, leveling, watering & well ramming in layers n.exceeding 25 cm in soft/loose soil complete all as specified and directed. |
| 107 | Removing of excavated materials to a distance n. exc 50m and depositing where directed at a level n exc 1.5m above the starting point in oft/loose soil complete all as specified. |
| 108 | Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified. Please Enable Macros to View BoQ information |
| 109 | Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified. Please Enable Macros to View BoQ information |
