|
| 1 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. 2.28.1 All kinds of soil |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. 2.6.1 All kinds of soil |
| 3 | Sand zone V (Jamuna) |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 7 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 8 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 9 | Manufacturing, supplying and fixing retro reflective sign boards madeup of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee sectionISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats,providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zincchromate yellow primer (vertical MS-Tee support to be painted in black and white colours). Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing, specification and direction of Engineer-in-charge 16.59.1 Mandatory/ Regulatory sign boards of 900 mm diameter with support length of 3750 mm |
| 10 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 11 | CEMENT PLASTER (IN COARSE SAND) 12 mm cement plaster of mix : 13.4.1 1:4 (1 cement: 4 coarse sand) |
| 12 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished,machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. 8.2.1 Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble Area of slab upto 0.50 sqm |
| 13 | SEATED PULLER /PULL CHAIR MADE FROM “C” CLASS G.I PIPE. DIMENSIONS: - 1900MM (LENGTH) X 740MM (WIDTH) X 1920MM. (HEIGHT). SAFE AREA:- 1.2MTR X 3MTR. SEATED PULLER EQUIPMENT MADE UP OF “C” CLASS G.I. PIPE OF DIFFERENT NB.NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE CENTER PIPE IS OF 100NB MADE FROM “C” CLASS G.I. PIPE. BOTTOM SUPPORT IS OF M.S. ROUND PLATE OF DIA 250 MM & 10MM THICKNESS WELDED. ALL LINKAGES ARE MADE UP OF 25NB “C” CLASS G.I. PIPE. THE HANDLE FRAME IS OF 32NB “C” CLASS G.I. PIPE. THE SEAT FRAME IS OF 32NB “C” CLASS G.I. PIPE. TO BUILD STRUCTURE BUSHES ARE USED WHICH ARE MADE FROM SEAMLESS PIPE OF 60MM O.D. AND 5MM THICKNESS AS WELL AS 60MM DIAMETER SOLID BAR BUSH USED. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS. WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. FOUNDATION COVER CLOSING CAP IS MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE. THE SEATS AND BACK RESTS ARE FITTED ON THE OUTER FRAMES ARE MADE UP OF M.S. SHEET OF SIZE 330 MM X 300 MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED IN TOOLS AND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES.CLOSING CAPS ARE MADE UP OF FROM INJECTION MOULDED PLASTIC LLDPE / HDPE.PINS USED OF DIAMETER 25MM AND 17MM ARE MADE UP FROM SAE 8620 BRIGHT MATERIAL. THE BEARINGS USED ARE OF “6205 2RS1” AND “6203 2RS1” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND.HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY.THECIRCLIPS USED FOR ASSEMBLY ARE OF A16. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) |
| 14 | BACK EXTENSION DIMENSIONS: - 1400MM (LENGTH) X 700MM (WIDTH) X 820MM (HEIGHT). SAFE AREA: - 2.4MTR X 1.7MTR. BACK EXTENSION EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB PIPE. (NB STANDS FOR NOMINAL BORE I.E. INTERNAL DIAMETER OF PIPE IN MM) THE MAIN FRAME IS OF 50MM NB MADE FROM “C” CLASS G.I. PIPE. THE FOOT RESTING FRAME OF 32MM NB MADE FROM ”C” CLASS G.I. PIPE. THE HANDLE FRAME IS OF 25NB MADE FROM “C” CLASS G.I. PIPE. THE SEAT FITTED ON THE OUTER FRAMES IS MADE UP OF M.S. SHEET OF SIZE 330 MM X 300MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED IN TOOLS AND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES. THE FOUNDATION USED FOR FIXING IS CONSISTS OF 50MM NB MADE FROM ”C” CLASS G.I. PIPE.THE FOOTRESTS ARE MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE). |
| 15 | SKY WALKER DIMENSIONS: - 1720MM (LENGTH) X 630MM (WIDTH) X 1750MM.(HEIGHT). SAFE AREA: - 2.7MTR X 1.6MTR. SKY WALKER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB.NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE MAIN FRAME PIPE IS OF 80MM NB MADE FROM “C” CLASS G.I. MATERIAL WHICH IS BEND AT THE RADIUS OF 250MM.THE LEG MOVEMENT FRAME IS OF 50 X 50MM X 3MM THICK CRC SQUARE PIPE. SLEEVES ARE MADE UP OF 100 MM OD M.S. PIPE WITH THICKNESS 5MM. THIS RESULTS IN EASY REPLACEMENT OF BEARINGS, PINS AND HANDLE THE HANDLE FRAME IS OF 25MM NB MADE FROM “C” CLASS G.I. PIPE. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS. WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. TWO FOUNDATIONS ARE PROVIDED FOR RIGID SUPPORT. THE FOOTRESTS MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE. CLOSING CAPS ARE MADE UP OF INJECTION MOULDED PLASTIC LLDPE / HDPE. THE PINS USED ARE MADE UP OF DIA 25MM SAE8620 BRIGHT MATERIAL. PINS ARE FIXED AT THE OUTER END WITH M8 GRUB SCREWS AND DIA.8MM SS BALL. THE BEARINGS USED ARE “62052RS1” ARE PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE CERCLIPS USED FOR ASSEMBLY ARE OF A24 TYPE. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE). |
| 16 | CHEST PRESS . DIMENSIONS: - 2000MM (LENGTH) X 710MM (WIDTH) X 2200MM. (HEIGHT). SAFE AREA: - 3.0MTR X 1.7MTR. CHEST PRESS EQUIPMENT MADE UP OF “C” CLASS G.I. PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE CENTER PIPE IS OF 100NB MADE UP OF “C” CLASS G.I. PIPE. THE BOTTOM WELDED WITH SUPPORT OF M.S. ROUND PLATE OF DIA 250 MM & 10MM THICKNESS. THE CONNECTING PIPES ARE MADE UP FROM 25NB “C” CLASS G.I. PIPE. THE HANDLE FRAME IS MADE UP FROM 32NB “C” CLASS G.I. PIPE. TO BUILD STRUCTURE BUSHES ARE USED WHICH ARE MADE FROM MS SEAMLESS PIPE OF 60MM O.D. AND 5MM THICKNESS AS WELL AS 60MM DIAMETER SOLID BAR BUSH IS USED. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS. WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. THE SEATS AND BACK RESTS ARE FITTED ON THE OUTER FRAMES ARE MADE UP OF M.S. SHEET OF SIZE 330MM X 300 MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED IN TOOLS AND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES. CLOSING CAPS ARE MADE UP OF INJECTION MOULDED PLASTIC LLDPE / HDPE. FOUNDATION COVER CLOSING CAP IS MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE. PINS USED OF DIAMETER 25MM AND 17MM ARE MADE UP FROM SAE 8620 BRIGHT MATERIAL. BOLT M8X16 MM AND NYLOCK NUT OF M8 MADE OF SS 304 USED ON NYLON CAP MOUNTED ON PINS TO PROTECT BEARINGS AND PINS FROM RAIN AND DUST. THE BEARINGS USED ARE OF “62052RS1” &“62032RS1” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE CER CLIPS USED FOR LOCKING IS MADE UP OF A24 MM & A16MM. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE). |
| 17 | HORSE RIDER DIMENSIONS: - 1180MM (LENGTH) X 400MM (WIDTH) X 1400MM. (HEIGHT). SAFE AREA: - 2.2MTR X 1.4MTR. HORSE RIDER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB.NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE MAIN FRAME OF 100NB MADE FROM “C” CLASS G.I. PIPES WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. SEAT PROVIDED ARE MADE UP OF MS DEEP DRAW QUANTITY OF 2MM THICKNESS WITH NO JOINT WITH UNIFORM OUTER EDGE RADIUS 20MM. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. THE LEG MOVEMENT FRAME IS OF 32NB MADE FROM “C” G.I. PIPE. THE HANDLE FRAME IS OF 32 NB MADE FROM “C” CLASS G.I. PIPE. THE FOOTRESTS ARE MADE FROM 25 NB “C” CLASS G.I. PIPE. PINS USED OF DIAMETER 17 MM ARE MADE UP FROM SAE 8620 BRIGHT MATERIAL. N THE BEARINGS USED OF “62032RS1” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS FOR ASSEMBLY. THE SER CLIPS USED FOR ASSEMBLY ARE OF A24 MM. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE). |
| 18 | AIR WALKER PROVIDING AND FIXING AIR WALKER MADE FROM “C” CLASS GI PIPE. THE CENTER PIPE IS OF 80MM NB MADE FROM “C” CLASS MS PIPE, 32MM NB:- AIR WALKER PEDAL FRAME DULY BEND, 25MM NB:- AIR WALKER HANDLE FRAME DULY BEND AND THE BOTTOM SUPPORT OF M.S. ROUND PLATE OF 250 MM DIA& 10MM THICKNESS IS WELDED AT BOTTOM. MS PLATE OF 245 X 113 X 2.8MM :- FOOTREST SUPPORT PLATE. THE LEG MOVEMENT FRAME IS OF 40MM NB MADE FROM “C” CLASS MS PIPE. THE HANDLE FRAME IS OF 25MM NB MADE FROM “C” CLASS GI PIPE. THE FOUNDATION USED FOR FIXING IS CONSISTS OF THREE EQUAL ITEMS I.E. 80MM NB MADE FROM “C” CLASS GI PIPE, M.S. ROUND PLATE OF 250 MM DIA & 10MM THICKNESS & 25 MM X 25MM M.S. ANGLE OF 3 MM THICKNESS. MS PIPE 48 X 48 X 2.8MM:- FOOTREST FRAME SUPPORT. MS ANGLE 23 X 23 X 1.8MM:- FOUNDATION SUPPORT FRAME. MS FLAT 48 X 9MM:- FOUNDATION PLATE SUPPORT. MS BRIGHT MATERIAL:- PINS MADE OF DIA.25MM. MS PLATE OF 8MM:- AIR WALKER PEDAL L-BEND, SUPPORT. 60MM DIA SEAMLESS PIPE:- BUSHES. BEARINGS:- PERMANENT LUBRICATED BEARINGS 6205. CLOSING CAPS MADE FROM TOP QUALITY FRP MATERIAL WITH 2 MM THICKNESS. HDPE / LLDPE PLASTIC :- CLOSING CAP, AIR WALKER FOOTREST. THE PINS USED ARE MADE UP OF 25MM DIAMETER BRIGHT BAR. THE BEARINGS USED BE PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM S.S. MATERIAL. THE SER CLIPS USED FOR ASSEMBLY ARE OF 25 MM DIAMETER. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) |
| 19 | PROVIDING AND FIXING SURF BOARD MADE FROM “C” CLASS GI PIPE. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS GI PIPE, AND THE BOTTOM SUPPORT OF M.S. PLATE OF 250 MM DIA& 10MM THICKNESS IS WELDED AT BOTTOM. THE HANDLE FRAME IS OF 40MM NB & 25MM NB MADE FROM “C” CLASS GI PIPE. THE MOVEMENT FRAME IS MADE UP OF 50MM NB “C” CLASS GI PIPE. THE FOUNDATION USED FOR FIXING CONSISTS OF THREE EQUAL ITEMS I.E. 100MM NB MADE FROM “C” CLASS GI PIPE, M.S. ROUND PLATE OF 250 MM DIAMETER & 10MM THICKNESS, 25MM X 25MM X 3MM M.S. ANGLE. TO JOIN THE CENTRE PIPE & HANDLE FRAME SEAMLESS PIPE OF 130MM DIA& 3MM THICKNESS IS USED. FOR THE MOVEMENT, BUSHES ARE USED & FOR IT 60MM DIA WITH 3MM THICKNESS & 60MM SOLID BAR IS USED. THE FOOTRESTS IS MADE FROM FRP/C.I./ALUMINUM CASTING MATERIAL, ITS SIZES ARE 320 MM X 270 MM & 5 MM THICKNESS. FOR SUPPORT OF FOOTREST IS 200MM X 250MM WITH 5MM THICKNESS M.S. PLATE AND 50MM X 50MM CRC SQUARE PIPE WITH 2MM THICKNESS IS USED. CLOSING CAPS MADE FROM TOP QUALITY FRP MATERIAL WHICH IS OF 2 MM THICKNESS. THE PINS USED ARE MADE UP OF 25 MM DIAMETER HARDEN BRIGHT BAR. THE BEARING USED BE PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE HANDLES USED ARE OF RUBBER GRIP. THE NUT BOLTS USED FOR ASSEMBLY IS MADE FROM S.S. MATERIAL. THE BUSHES (STOPPER) USED TO AVOID THE COLLUSION MADE FROM POLY URETHIN PLASTIC MATERIAL OF 50 MM DIA. THE SER CLIPS USED FOR ASSEMBLY IS OF 25 MM DIA. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE). |
| 20 | TRIPPLE TWISTER STANDING DIMENSIONS: - 1150MM (LENGTH) X 1150MM (WIDTH) X 1580MM. (HEIGHT). SAFE AREA: - DIA 2.1MTR. TRIPLE TWISTER MADE FROM “C” CLASS GALVANIZED IRON (G.I.) PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE CENTER PIPE IS OF 100NB MADE FROM OR “C” CLASS G.I. ROUND PIPE. THE BOTTOM SUPPORT WELDED IS OF M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. THE STANDING FRAME IS OF 32NB MADE FROM “C” CLASS G.I. PIPE. THE HANDLE FRAME OF TRIPLE TWISTER IS OF 25 MM NB MADE FROM OR “C” CLASS G.I. PIPE. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80MM NB OR “C” CLASS WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLE OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPE OF 3MM THICKNESS THE STANDING PLATE IS FITTED ON THE FRAME MADE UP OF DIA 80MM SEAMLESS PIPE. M.S. ROUND PLATE OF SIZE DIA 300MM X 10MM THICKNESS. CLOSING CAPS OF TOP QUALITY FIBER REINFORCED PLASTIC MATERIAL WHICH IS OF 2 MM THICK. THE PINS USED ARE MADE UP OF DIA 25 MM SAE8620 BRIGHT MATERIAL. THE BEARINGS USED ARE OF “6205ZZ” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND (FAG/SKF). HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) |
| 21 | SHOULDER BUILDER PROVIDING AND FIXING SHOULDER BUILDER MADE FROM C- CLASS GI PIPE. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS GI PIPE, AND THE BOTTOM SUPPORT OF M.S. ROUND PLATE OF 250 MM DIAMETER & 10MM THICKNESS IS WELDED AT BOTTOM. THE HANDLE MOVEMENT FRAME IS OF 25 NB & 20 NB MADE FROM “C” CLASS GI PIPE. TO JOIN THE CENTRE PIPE & HANDLE MOVEMENT FRAME SEAMLESS PIPE OF 130MM DIA& 3MM THICKNESS IS USED. THE FOUNDATION USED FOR FIXING CONSISTS OF THREE EQUAL ITEMS I.E. 100MM NB MADE FROM “C” CLASS GI PIPE, M.S. ROUND PLATE OF 250 MM DIA& 10MM THICKNESS & 25 MM X 25MM X 3MM M.S. ANGLE. CLOSING CAPS MADE FROM TOP QUALITY FRP MATERIAL WHICH IS OF 2 MM THICKNESS. THE PINS USED ARE MADE UP OF 25 MM DIA BRIGHT BAR. THE BEARING USED BE PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM S.S. MATERIAL. THE SERCLIPS USED FOR ASSEMBLY IS OF 25 MM DIAMETER. THE POLY URETHIN PLASTIC BUSH IS USED FOR HANDLING. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) |
| 22 | TRICEPS PULLER (DIMEMSIONS:- 2110MM (LENGTH) X 600MM (WIDTH) X 1600MM (HEIGHT) TRICEPS PULLER IS MADE FROM “C” CLASS GI-PIPE. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS GI-PIPE, AND THE BOTTOM SUPPORT IS OF MS ROUND PLATE OF 250MM DIA& 10MM THICK IS WELDED AT THE BOTTOM OF THE PIPE. THE REMAINING FRAME IS MADE OF 32MM NB “C” CLASS GI-PIPE. THE HANDLE FRAME IS MADE OF 32MM NB & 25MM NB “C” CLASS GI-PIPE. THE SEAT FRAME IS OF 32MM NB “C” CLASS GI-PIPE. FOR THE ASSEMBLY DIFFERENT BUSHES ARE USED WHICH IS MADE FROM 60MM WITH 3MM THICK SEAMLESS PIPE IS USED. THE FOUNDATION USED FOR FIXING IT CONSIST OF THREE EQUAL ITEMS I.E 80MM NB MADE FROM “C” CLASS GI-PIPE, MS ROUND PLATE OF 250MM DIA& 10MM THICK, 25MMX25MMX3MM MS ANGLE. CLOSING CAPS ARE MADE FROM TOP QUALITY LLDPE MATERIAL WHICH IS OF 2MM THICK. THE PINS USED ARE MADE UP OF 25MM & 17MM DIA SOLID BAR. THE BEARINGS USED ARE OF “6205 & 6203” PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM SS MATERIAL. THE CIRCLIP USED FOR ASSEMBLY IS MADE UP OF 25MM & 17MM DIA.HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE FOUNDATION PIPES ARE EMBEDDED IN CC STOCK AND PAINTING IS DONE BY ATTRACTIVE COLOR SPRAYING AFTER PROPER SURFACE TREATMENT, THE INITIAL COAT OF PRIMER SURFACE IS APPLIED BEFORE TOP COAT. THE POWDER COATING IS DONE FROM POLY RETHANE& EPOXY POWDER WITH 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) |
| 23 | SINGLE SKYWALKER (DIMEMSIONS:- 1850MM (LENGTH) X 520MM (WIDTH) X 1780MM (HEIGHT). SINGLE SKYWALKER IS MADE FROM “C” CLASS GI-PIPE. THE CENTER PIPE IS OF 50MM NB MADE FROM “C” CLASS GI-PIPE, AND THE BOTTOM SUPPORT IS OF MS ROUND PLATE OF 250MM DIA& 10MM THICK IS WELDED AT THE BOTTOM OF THE PIPE. THE REMAINING FRAME IS MADE OF 50MM NB “C” CLASS GI-PIPE. THE HANDLE FRAME IS MADE OF 25MM NB& 32MM NB “C” CLASS GI-PIPE. MIDDLE SUPPORT IS OF 40MM NB “C” CLASS GI-PIPE. LOWER FRAME IS MADE OF 32MM NB “C” CLASS GI-PIPE. FOR THE ASSEMBLY DIFFERENT BUSHES ARE USED WHICH IS MADE FROM 60MM WITH 3MM THICK SEAMLESS PIPE IS USED. THE FOUNDATION USED FOR FIXING IT CONSIST OF THREE EQUAL ITEMS I.E 80MM NB MADE FROM “C” CLASS GI-PIPE, MS ROUND PLATE OF 250MM DIA& 10MM THICK, 25MMX25MMX3MM MS ANGLE. CLOSING CAPS ARE MADE FROM TOP QUALITY LLDPE MATERIAL WHICH IS OF 2MM THICK. THE CIRCLIPS USED FOR ASSEMBLY ARE MADE UP OF 25MM DIA. THE PINS USED ARE MADE UP OF 25MM DIA SOLID BAR. THE BEARINGS USED ARE OF “6205& 6203 PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM SS MATERIAL.HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY THE FOUNDATION PIPES ARE EMBEDDED IN CC STOCK AND PAINTING IS DONE BY ATTRACTIVE COLOR SPRAYING AFTER PROPER SURFACE TREATMENT, THE INITIAL COAT OF PRIMER SURFACE IS APPLIED BEFORE TOP COAT. THE POWDER COATING IS DONE FROM POLY RETHANE& EPOXY POWDER WITH 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) |
| 24 | LEG PRESS LEG PRESS IS MADE FROM “C” CLASS GI-PIPE. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS GI-PIPE, AND THE BOTTOM SUPPORT IS OF MS ROUND PLATE OF 250MM DIA& 10MM THICK IS WELDED AT THE BOTTOM OF THE PIPE. THE REMAINING FRAME IS MADE OF 32MM NB “C” CLASS GI-PIPE. THE HANDLE FRAME IS MADE OF 25MM NB “C” CLASS GI-PIPE. MIDDLE SUPPORT IS OF 25MM NB “C” CLASS GI-PIPE. LOWER FRAME IS MADE OF 32MM NB “C” CLASS GI-PIPE. FOR THE ASSEMBLY DIFFERENT BUSHES ARE USED WHICH IS MADE FROM 60MM WITH 3MM THICK SEAMLESS PIPE IS USED. THE FOUNDATION USED FOR FIXING IT CONSIST OF THREE EQUAL ITEMS I.E 80MM NB MADE FROM “C” CLASS GI-PIPE, MS ROUND PLATE OF 250MM DIA& 10MM THICK, 25MMX25MMX3MM MS ANGLE. CLOSING CAPS ARE MADE FROM TOP QUALITY LLDPE MATERIAL WHICH IS OF 2MM THICK. THE PINS USED ARE MADE UP OF 25MM DIA SOLID BAR. THE BEARINGS USED ARE OF “6205 PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM SS MATERIAL.HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE CIRCLIPS USED FOR ASSEMBLY ARE MADE UP OF 25MM DIA. THE FOUNDATION PIPES ARE EMBEDDED IN CC STOCK AND PAINTING IS DONE BY ATTRACTIVE COLOR SPRAYING AFTER PROPER SURFACE TREATMENT, THE INITIAL COAT OF PRIMER SURFACE IS APPLIED BEFORE TOP COAT. THE POWDER COATING IS DONE FROM POLY RETHANE& EPOXY POWDER WITH 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) |
| 25 | Providing and engraving lettering on granite/marble inauguration stone by computerized machine engraving of approved font, size and layout, having minimum depth 3-5mm, including filling with weather resistant enamel paint (gold/white as approved), complete as per approved design. The stone shall be properly polished with smooth finish, edges machine out, and fixed in position with suitable adhesive and stainless steel clamps. The item includes all materials, labour, tools, carriage, and protection arrangements till inauguration, complete as per direction of Officer-in-Charge. Please Enable Macros to View BoQ information |
