|
| 1 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. Hard rock (requiring blasting) DSR-2023 (Civil), Item No. 2.9.2 |
| 2 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete DSR-2023 (Civil), Item No. 2.27 |
| 3 | Providing & laying in cement concrete 1:4:8 (1cement : 4 finesand : 8 graded brick aggregate 40 mm nominal size) including supply of materials, labour and T&P etc. required for proper compilation of work. and curing complete also including cost of formwork in foundations & floors. DSR-2023 (Civil), Item No. 4.1.8 |
| 4 | providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland /portland Slag cement, admixtures in recommended proportions as per iS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. DSR-2023 (Civil), Item No. 5.33.1 All works upto plinth level concrete of m25 grade with minimum cement content of 330 kg /cum 5.33.1.1 |
| 5 | All works above plinth level upto floor V level concrete of m25 grade with minimum cement content of 330 kg /cum 5.33.2.1 |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete DSR-2023 (Civil), Item No. 5.9.1 |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, Abutments, posts and Struts DSR-2023 (Civil), Item No. 5.9.6 |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick DSR-2023 (Civil), Item No. 5.9.21 |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick DSR-2023 (Civil), Item No. 5.9.20 |
| 10 | Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) DSR-2023 (Civil), Item No. 6.2.1 |
| 11 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 insuperstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) DSR-2023 (Civil), Item No. 6.4.2 |
| 12 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand) DSR-2023 (Civil), Item No. 6.13.2 |
| 13 | Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources) DSR-2023 (Civil), Item No. 4.1 |
| 14 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration DSR-2023 (Civil), Item No. 2.35..3.1 |
| 15 | Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20% DSR-2023 (Civil), Item No.2.34.1 |
| 16 | Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement: 3 fine sand) : Flush / Ruled/ Struck or weathered pointing DSR-2023 (Civil), Item No. 13.31.1 |
| 17 | 15mm thick cement plaster with cement mortar in proportion of 1:4 cement and coarse sand. DSR-2023 (Civil), Item No. 13.2.1 |
| 18 | Steel Rainforment for RCC work inculuding Straighteeing, Cutting Bending Placing In Position And Binding all Completed Upto Plinth Level.Thermo-Mechnanically Treated bars of Grade Fe 500D OR MORE DSR-2023 (Civil), Item No. 5.22.6 |
| 19 | Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Makrana white second quality DSR-2023 (Civil), Item No. 11.23.1 |
| 20 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqmover and including priming coat of exterior primer applied@ 2.20 kg/10 sqm) DSR-2023 (Civil), Item No. 13.47.1 |
| 21 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. DSR 2022 (1.1.3) |
| 22 | Supply & fixing of power plug with 15 amp 250 volts flush type switch & 5 pin 15 amp 250 volts flush type socket in suitable M.S. box of 175 mm * 100mm * 50 mm size with bakelite sheet cover 3 mm thick fixed with brass machine screws & washers complete in all respect. 1139 |
| 23 | Supply & wiring of sub main with FR P.V.C. insulated 1100 volts grade single core copper conductor cable in heavy gauge P.V.C. coduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting complete with FR PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. 2 x 4.00 sq. mm. With 1 x 2.5 sq.mm. Earth wire In 20 mm dia conduit. 221 (C) |
| 24 | 2x 6 sq. mm. With 1 x 4 sq.mm. Earth wire In 25 mm dia conduit. 222 © |
| 25 | 2 x 16 sq. mm. With 1 x 10 sq.mm. Earth wire In 32 mm dia conduit. 224 © |
| 26 | Supply and laying of heavy duty PVC conduit complete with bend and other accessories as required and 14 S.W.G. fish steel wire etc. in slab alongwith reinforcement before concreting and plastering complete in all respects. 20 mm dia. PVc conduit 281(A) |
| 27 | 25 mm dia. PVC conduit 282(A) |
| 28 | S/F of surface / flush mounting TPN Distribution board without MCB complete in all respects as directed at site . 12 WAYS Cat(A) 1029(A) |
| 29 | Supply and fixing of 6 Amp to 32 Amp MCB(10KA)C Curve Cat(A) 1002 |
| 30 | Supply Fixing and making commection of 30 MA E.L.C.B. (Earth leakage circuit breaker) of din/R.C.C.B. rail mounting complete in all respects as per direction and satisfaction of engineer-in-charge. 40 Amp 2 Pole 393 |
| 31 | Supply & burrying of safe earthing electrode T-39 (Hot Dip Galvanized), Length up to 3000mm, outer pipe 76mm inner Dia 38mm terminal Dia 12mm, outer GI pipe of 16 SWG and inner GI pipe of 12 SWG with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixtuer (CCM) Having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of rataining capacity along with 30cm squre C.I. frame with hinged cover & masonry housing. (From electrode terminal to switch board, cost of 25 x 3 GI, strip will be extra)Make:as approved in U.P.P.W.D., & C.P.R.I. Certified 725D |
| 32 | Supply & Laying of 25mm x 3mm G. I. strip from earth electrode directly in the ground as required complete in all respect. 716 |
| 33 | S/F of single light wall bracket on matching M.D.F.E.G. board base etc. complete in all respects. Category AAA 412 |
| 34 | Supply & fixing of Recess/Surface/Pendent mounting round 6 to 8 Watt LED down lighter having powder coated die cast Aluminium housing with heat sink, diffuser/reflecter, and driver set complete in all respect. Category AAA 1401 |
| 35 | Supply and Fixing of LED Tube Light with batten suitable for up to 1X22 watt LED tube light fitting complete including tube on surface complete in all respect. Category AAA 1413 |
| 36 | Supply and Fixing of LED Tube Light with batten suitable for up to 2X22 watt LED tube light fitting complete including tube on surface complete in all respect. Category AAA 1414 |
| 37 | Erection and testing of ceiling fan and regulator for room height upto 3.5mts. including supply of 3mm thick G.I. down rod 19mm dia duly painted, complete in all respects. 1116 |
| 38 | Erection and testing of exhaust fan on the existing hole with suitable size of rag bolts nuts and washers etc complete in all respects. 1120 |
| 39 | Supply and fixing of 16 gauge MS drum duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respect. 1122 |
| 40 | Supply & fixing hexagonal/Round G.P. Fan box of approved make made up of 1.0 mm thick ISI marked G.P. Sheet spot welded four to Eight holes of 25.4mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5mm G.P. Sheet made upper & lower cover duly screwed fitted with 300mm round zink coated M.S. Bar x 12mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material labour, T & P etc required for proper completion of the work. 1149 |
| 41 | S/F of danger board fabricated from 10 gauge M.S. sheet as per E/I rules. 1109 |
| 42 | Supply & Erection of factory fabricate & wired metal clad dust and vernim proof floor mounting, M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN MCCB's (Four pole 36 KA with thermal magnetic release) switches complete and instrument chamber etc. completed in all respects. The instrument chamber shall be seprated and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters (KVA,P.F, KW etc) in each phase with touch type selector switches for different readings , intrument fuses, current transformer etc. the panel board shall have suitable capacity electrolytic aluminium busbars as per IS8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCB's shall be completed with suitable cable and boxes, compression glands and indicating lamp on incoming etc. The job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above shall have Ammeter.The panel board shall be fabricated with CRCA shee with a minimum thicness of 1.6mm/2mm. Cubicle type switch board shall be of cat A & B only. Incoming 200Amp. MCCB-1No. Outgoing 100 Amp MCCB-1 No & 63 Amp MCCB-3Nos 812C |
| 43 | Supply & erection of AC 1200mm Sweep, 220/240 Volts, 50 Hz ceilling fan with standard down rod, blades including connection etc. complete as required-BEE-5 Star rated 1501 |
| 44 | Supply & erection of AC 230/250 Volts, 50 Hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required-Make: USHA Cat No. TURBO JET DLX 300 mm sweep MR |
| 45 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means overareas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including gettingout and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge.All kinds of soil 2.6.1 (DSR 2023) |
| 46 | Sand filling in plinth under floors excluding supply of necessary quantity of sand from a distance not exceeding 8 km from the site of work and including watering, ramming, consolidating and dressing etc required for proper compilation of work. (Labour only) 2.27 (DSR 2023) |
| 47 | Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desireddensity, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 16.78.1 (DSR 2023) |
| 48 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. 16.68 (DSR 2023) |
| 49 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineerin- charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). 16.69 (DSR 2023) |
| 50 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means overareas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including gettingout and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge.All kinds of soil 2.6.1 (DSR 2023) |
| 51 | Supplying and filling in plinth with sand under floors, including watering, ramming,consolidating and dressing complete. 2.27 (DSR 2023) |
| 52 | Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desireddensity, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 |
| 53 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. 16.91.2 (DSR 2023) |
| 54 | Providing, fabricating and installing FRP murals in stone dust finish, molded in high-grade FRP with minimum 6–8 mm thickness, reinforced with MS frame, finished with stone dust texture and protective coating, showcasing gallery-specific perspective-based curatorial narratives, complete with surface preparation, mounting hardware, alignment, lighting coordination, and installation as per approved designs and curatorial drawings. MR |
| 55 | Providing and fixing CNC-carved stone murals using natural stone / reconstituted stone panels, CNC-cut with traditional Indian architectural motifs, including backing frame, anchoring system, surface finishing, edge treatment, and installation for curatorial support, complete as per approved patterns and specifications. MR |
| 56 | Providing CNC-cut murals of size 8’×4’ fabricated on coated steel sheets, laser/CNC cut with Indian architectural designs, including primer, anti-corrosive treatment, powder coating / PU finish, structural supports, anchoring, and installation complete. MR |
| 57 | Providing canvas printed artworks using museum-grade archival ink on stretched canvas frames, sizes varying from 3’×2’ to 6’×4’, including graphic design finalization, printing, framing, mounting hardware, and installation showcasing curatorial narratives. MR |
| 58 | Design, supply, installation, testing and commissioning of VR experience stations, including VR machines, headsets, controllers, custom interactive content development, narration, animation, software integration, electrical connections, safety accessories, and complete setup as per approved curatorial intent. MR |
| 59 | Supply of DLP Laser Phosphor projector Min. 9600 Lumens with sealed light engine for dust protection capable of 24 x 7 operation, Laser light source having 20,000 hrs. life, Support UHD-4K 3840x2160 resolution, Contrast Ratio: 3,000,000:1, HDR10 for precise natural colour, The projector should capable of being mounted and operative in any orientation (360deg tilt and roll), 3D compatibility with DLP Link, Art-Net controller for Stage Console system, Inputs:, 2 x HDMI v2 (HDCP v2.2), 1 x HD Base T, Controls: RS232, Control: Crestron Room View, along with Standard throw Lens. Approved OEM: Delta, DP NEC, Panasonic MR |
| 60 | ITC of DLP Laser projector with 8,000 ISO Lumen or higher brightness,Contrast ratio (Dynamic) min. 18000:1 or higher, 24/7 operation, IP60, sealed optics complete dust protection and filterless operation with liquid cooled technology and Typical illumination Life: 20,000 hours or better. Inputs :1 x Display port, , 2 x HDMI, 1 x HDBaseT, 3G-SDI in/out Controls: 3D sync in/out, Crestron RoomView Connected, LAN,RS-232,AMX,DMX Art-Net along with suitable lens. All critical PCB’s of the projectors are coated by a min of 0.06mm of conformal coating. Make : DP/Barco/Panasonic or equalent MR |
| 61 | Supply, laying, termination, testing and commissioning of all required cables, connectors, professional speakers and associated accessories compatible with continuous 24×7 operation, 4K UHD signal transmission, Crestron RoomView, AMX, DMX, Art-Net and stage control systems, complete in all respects as per site requirement and direction of Engineer-in-Charge. Make shall be reputed OEM or equivalent approved by Engineer-in-Charge. MR |
| 62 | Providing and fixing 75” LED 4K Smart Display Units, including wall mounting / floor stand, content loading, media players, cabling, electrical connections, testing, and commissioning for informational and interpretive display purposes. MR |
| 63 | Providing FRP stone-finish sculptures in traditional Indian style forms, handcrafted with high-strength FRP, internal steel armature, stone texture finish, protective coating, transport, erection, anchoring, and placement as per approved curatorial layouts. MR |
| 64 | Providing and installing information panels made of SS 304, including laser-cut / etched text and graphics, satin/matte finish, standoffs, bilingual content printing, fixing accessories, and installation complete. MR |
| 65 | Providing stained glass statue of Radha, 7’ height, handcrafted using layered stained glass panels with internal structural support, illumination integration, transportation, erection, and installation complete as per approved artistic design. MR |
| 66 | Content creation including audio and visual production, comprising research, scriptwriting, multilingual narration, voice recording, sound design, animation, video production, editing, subtitles, formatting, and delivery for museum displays, immersive zones, and AV systems, complete as a composite job. MR |
| 67 | Museum curation and documentation services, including concept development, storyline framing, artifact mapping, spatial sequencing, interpretive planning, documentation, drawings, coordination with execution teams, and final submission as per government museum standards. MR |
| 68 | Providing museum display cabinets made of powder-coated MS/Aluminium frames with museum-grade low-iron glass, integrated focus lighting, locks, ventilation, and complete installation. MR |
| 69 | Executing graffiti artwork over walls, including surface preparation, primer, artist-executed thematic graffiti, protective coating, scaffolding, and completion as per approved curatorial artwork. MR |
| 70 | Providing partition walls using aluminium framework and HDHMR boards, including framing, board fixing, joint treatment, putty, primer, paint finish of approved shade, and integration with display elements, complete in all respects. MR |
| 71 | Supplying curated display replicas, including books, idols, documents, artifact replicas, aging/finishing treatment, mounting accessories, and placement as per approved curation plan.MR |
| 72 | Design, Supply, and Installation of Decorative Light Fixture with 65W power consumption and 4000K color temperature. The fixture shall provide high luminous efficacy with uniform light distribution. Complete with durable housing, wiring, and necessary accessories for long-lasting performance. 3 Mtr MR |
| 73 | Construction of the Pole Plinth Size 1400mm55mm 55mm including RCC Concrete M-24, 12mm Dia Steel and 1.5M Long, 8 Nos @ 50mm*500mm Ring 8mm Dia Steel, 200mm C/C Including All Complete MR |
| 74 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 x 2.5 sq. mm + 1 X 2.5 sq. mm earth wire DSR 20221.7.2 |
| 75 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 16 sq.mm 4 core SOR 501(2018) |
| 76 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal) DSR 202214.16.1 |
| 77 | Supplying, installing, testing and commissioning of following capacity TPN distribution tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with HRC fuses, interconnections, earthing etc. as required. 32A TPN 4 WAY. DSR 2022 3.3.6 |
| 78 | Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. SOR 504D(2018) |
| 79 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. DSR 20252.10.1 |
| 80 | Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 100 to 120 Watt. Confirming to IP 65 protection complete in all respect. SOR 1453 (2018) |
| 81 | supply and installation of Spot light 18w MR |
| 82 | supply and installation of High beem light 50w MR |
| 83 | upply & installation of Split Direct Expansion Air- Conditioners Suitable for operation on A/C supply single phase 50HZ 230 Volts with hermetically sealed compressor with air cooled condenser, motor capacitor and start run capacitor, relay and over load protector internal unit, with one indoor and one outdoor unit. The condenser unit will be placed outside the room on the terrace to avoid noise including standard length of suitable size copper tubing covered with-insulation tube. (High Wall Chorded/ Cordless)Suitable Capacity 3 Core sheathed/ PVC copper cable and a battery operated wireless remote unit. 2.00 TR (i) bee star Rated : 5 star eer3.4 SOR 2018 1503 C (i) |
| 84 | Design, supply, installation, testing, and commissioning of holographic projection display system. Providing advanced holographic technology for three-dimensional floating visual presentation.System capable of displaying high-resolution animations and visual content.Holographic display to operate without the requirement of special viewing glasses.Supply of complete hardware, controllers, mounting structures, and accessories. Installation to be carried out as per approved drawings and site conditions. Integration with audio, lighting, or show control systems wherever required. Calibration and alignment for optimum brightness, clarity, and viewing angles.Testing, trial run, and final commissioning of the complete system.Handing over in fully operational condition including basic operator training.MR |
| 85 | Installation testing commissioning and programming for glow garden complete with combination of multiple LED lights including LED Noctura Glow, LED StrideLux, LEF Waterveil, LED PixieGlow combined to createthe effect for glow garden To cover a path way 25m long and 2.5m on each side of the path wayMR |
| 86 | Less 5% as per GO Please Enable Macros to View BoQ information |
