|
| 1 | Taking down Cement Plaster block masonry or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. of all as specified |
| 2 | Demolition of cement concrete (un reinforced ) in ground floors and pavings n.exc 15cm thick (below or above ground level ) as specified and directed by Engineer-in-Charge. |
| 3 | M&L for 15mm thick base plaster in cement mortar (1:4) sunken portion/roof etc admixing water proofing compound @ 200 ml per bag of cement complete all as specified and directed. (Water proofing compound will be measured and paid seprately as supply only). |
| 4 | M&L for two coats of RBR cement slurry in 1:2 proportion on complete horizontal and vertical areas of sunken floor complete all as specified. |
| 5 | Supply only integral liquid water proofing compound complete all as speified and directed. |
| 6 | M&L cement concrete bedding (1:5:10) type E2 using 40mm graded stone aggregate , jointing traps etc with RBR-modified mortar inluding priming of joints using RBR cement slurry complete all as specified abd directed. |
| 7 | M&L for 5 mm thick rendering for fair faces of concrete surfaces on ceiling in CM 1:3 for fair finished surfaces. |
| 8 | M&L for 10 mm thick rendering for fair faces of concrete surfaces on walls in CM 1:6 and finished even and smooth without using extra cement as specified. |
| 9 | M&L for preparing new plastered ceiling/soffits of chajjas surfaces and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge. |
| 10 | Complete removal of existing treatment on ceiling surfaces and applying two coats of white wash by finishing the surfaces even and smooth complete all as specified and directed by EIC. |
| 11 | M&L for preparing new plastered wall surfaces and applying two coats of distemper with distemper oil emulsion, white or tinted including one coat of wall care Putty by finishing the surfaces even and smooth complete all as specified and directed by EIC. |
| 12 | Taking down existing water proofing treatment on RCC slab / beams with bitumen felt with out damaging structure and removing the debris outside the MD land and M&L for plaster 15 mm thick on concrete surfaces in cement mortar 1:4 finished even and smooth using WPC @ 3% by weight of cement and preparing the surfaces to receive WPT treatment , applying a coat of bitumen primer confirm to IS - 3384-1986 @ 3% per sqm . providing APP modified membrane with non woven polyester reinforcement/mat ( centre core) by torch application over primed surfaces all as specified and directed by Engr-In- Charge |
| 13 | Complete removal of existing treatment on wall surfaces and applying two coats of distemper oil emuision, white or tinted including one coat of wall care putty by finishing the surfaces even and smooth complete all as specified and directed by EIC. |
| 14 | Taking down chowkhat or frames with shutter (without taking off shutters from the frames) n.exc 1.5 sqm |
| 15 | Taking down chowkhat or frames with shutter (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4.00 sqm each. |
| 16 | Taking down shutters of any description exc 1.0 sqm but n.exc 2.00 sqm each. |
| 17 | Taking down of shutters of any description of size exc 2.0 Sqm each, complete all as specified and as directed by the EIC. |
| 18 | Re- fixing of shutters in same opening description exc 1.0 sqm but n.exc 2.00 sqm each. |
| 19 | Re- fixing of shutters of in same opening any description of size exc 2.0 Sqm each, complete all as specified and as directed by the EIC. |
| 20 | S&F 125x60mm,1.25mm thick pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified including filling in frames with cement concrete type B-0, 1:2:4 (using 12.5mm graded aggregate) |
| 21 | S&F 105x60mm,1.25mm thick pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified including filling in frames with cement concrete type B-0, 1:2:4 (using 12.5mm graded aggregate) |
| 22 | M&L for cement concrete type C-1, 1:3:6 (using 20mm graded stone aggregate) as in bed blocks for fixing of hold fasts and the like including necessary formwork. |
| 23 | S&F 35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, with sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/ Gauge etc. Size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) complete. |
| 24 | S&F 35mm thick 2nd class hard wood factory made plain framed, paneled shutters (any number of panels), with lock rail and panel of 9mm BWP commercial ply or 12mm veveered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (part-I), kiln seasoned and chemically pressure treated. |
| 25 | S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed wih aluminium wire staples. |
| 26 | S&F 300mm length of bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cost or extraded sections and fixing bolts and sliding bolts of extraded sections or cost aluminium alloy. |
| 27 | S&Fstainless steel 100mm size of hinges butt hinges, medium weight. |
| 28 | S&F 150mm size extruded aluminium alloy handles, fabricated type. |
| 29 | S&F 150 mm size aluminium, anodised barrel tower bolt of extruded section. |
| 30 | S&F for 140mm floor door stopper of aluminium alloy body and tongue, anodised, fixed in floors. |
| 31 | S&F in repairs for 140mm floor door stopper of aluminium alloy body and tongue, anodised, fixed in floors. |
| 32 | M&L for preparation of new sufaces of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primer on wooden surfaces. |
| 33 | M&L for preparation of new sufaces of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer on steel surfaces. |
| 34 | S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed by Engr-in-Charge |
| 35 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed by Engr-in-Charge |
| 36 | S&F Anodised aluminium door shutters (Single/double shutter), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing anodised aluminum snap beading handles in each door, hinges, handles, anodised snap beading screws, hold fast complete all as specified and as directed |
| 37 | M&L for aluminium window with double side hung shutter for glazing and gauging and frame with one or more rebates made out of anodised aluminium section including section for fixing of aluminium grills with suitable fixtures, jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium beading screws, type B20 100mm long suitable handle and anodised aluminum fittings such as stay, hinges glazing with 5 mm thick tinted sheet glass and gauging with aluminium wire cloth of size 0.45mm dia of wire and 1.40mm aperture as per drg No. CEAA/TD/133 sheet No. 1/2 and 2/2 dated 13.12.02 except fixed glazing (FG) all as specified and directed.(Tint of glass shall be approved by GE) Note :- Aluminium grill fixed under above item shall be measured and paid separately |
| 38 | Supply only aluminium anodised grill of approved shape with opening in grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 6mm x 7mm Please Enable Macros to View BoQ information |
| 39 | Supply only aluminium anodised grill of approved shape with opening in grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 6mm x 7mm Please Enable Macros to View BoQ information |
