|
| 1 | Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out in soft soil complete all as specified and directed. |
| 2 | Excavation over areas, n. exc 1.5m deep and getting out in any type of soil complete all as specified and directed |
| 3 | Excavation over areas, exc 1.5m deep but n. exc 3m deep and getting out in any type of soil complete all as specified and directed |
| 4 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed. |
| 5 | Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed. |
| 6 | Materaial and labour PCC (1:3:6) type C2 (using 40 mm graded stone aggregate) for fdn/ mass concrete complete all as specified and as directed. |
| 7 | Material and labour for brick work with sub class 'B' brick straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6, complete all as specified and directed. |
| 8 | Material and labour for 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4, surface finished even and fair (without using extra cement) complete all as specified and directed. |
| 9 | Material and labour for extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including form work, moulds, mitred/stop ends etc complete all as specified and directed. |
| 10 | Material and labour for 300 mm DWC HDPE pipe of any colour suitable for water flow and confirming to IS 16098-2 and pressure rating SN-8/SN-16 into laying, Jointing and making connection to existing Chamber etc as required at site as per manufacturers instructions complete all as specified and directed. |
| 11 | Material and labour for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in coping, benching, bed block, lintel band, plinth courses etc. and similar work including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed. |
| 12 | Material and labour for PCC 1:2:4 type B-2 (using 40 mm graded crushed stone aggregate) as in surface channels and drains including necessary form work complete all as specified and directed. |
| 13 | Material and labour for 60 mm thick reinforced precast cement concrete 1:1:2 type B-1 (using 20mm graded stone aggregate) as in man cover bromatic slabs finish fair even and smooth without using extra cement (Top surface will be chequred finish) including necessary form work including 2mm thick CR sheet with 2 coats of bitumen paint and two nos PVC counter sunk handle 12mm dia to surface, complete all as specified and directed |
| 14 | MSupply and fixing of mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 15 | Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed |
| 16 | Material and labour for 100mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in hardstanding, laid in alternate bays and filling the joints with & including bitumen and sand 1:3 by weight, surface finished even and fair without using extra cement complete all as specified and directed. |
| 17 | Material and labour 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded crused stone agg) as in sub base complete all as specified and as directed. |
| 18 | Supply and fixing of plain, galvanised, 1mm thick mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed |
| 19 | Supply and fix of mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; staircase; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 including necessary welding, drilling hole, complete all as specified and directed. |
| 20 | Material and labour for two coats of synthetic enamel paint on new or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces, complete all as specified and directed. |
| 21 | Material and labour for coarse sand aggregate Spreading and levelling in layers nexc 25cm thick complete all as specified and directed. |
| 22 | Material and labour for gravel 12.50mm size aggregate Spreading and levelling in layers nexc 25cm thick complete all as soecified and directed. |
| 23 | Supply and labour in repair 110 mm bore PVC (SWR) pipe pressure 4Kgf/cm2 single socketed in any length with rubber ring, fixed on wall/ laid in trenches complete all as specified and directed. |
| 24 | Supply and labour 110 mm bore PVC (SWR) bends any radius with oval acess door complete all as specified and directed. |
| 25 | Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.50 Square metre but n.exc 4.0 Square metre Each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed. |
| 26 | Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n.exc 1.50 Square metre Each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed. |
| 27 | Taking down shutter of any description exc. 1.0 Square metre but n.exc 2.0 Square metre Each and removing from site complete all as specified and directed. |
| 28 | Supply and fix Ist Class hard wood, (Teak) Plain, solid straight Chowkats and Framed rebated on the solid, rounde or chamfered, put together with glue pinned at joints, Framed and Manufactured in situ. Noted:- The contractior shall bring the trunk of appropiate size as per directions of Engineer in charge at siteand necessary cutting and manufacturing sall only bed done at site. No factory made material allowed |
| 29 | Supply and fix 35 MM thick 1st Class hard wood (teak) manufactured in situ Glazed and skeleton shutters (single/Double) open reabted and prepared to receive glass, gauze, etc devided into squares, with plain chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, section 8 clause 8.24 (a).Note:- The contractor shall bring the trunk of appropriate size as per direction of Engineer in charge at site and necessary cutting and manufacturing shall onlybe done at site. No factory made material shall be allowed. |
| 30 | Supply and fix 30 MM thick 1st Class hard wood (teak) manufactured in situ plain Framed panelled shutters (single/double) (any number of panels), with panels of timber flat on both sides(feather edged) size of members of shutters as specified in SSR Part-I, section 8 clause 8.24 (b).Note:- The contractor shall bring the trunk of appropriate size as per direction of Engineer in charge at site and necessary cutting and manufacturing shall onlybe done at site. No factory made material shall be allowed. |
| 31 | Material and labour for melamine clear polishing high gloss/matt finish in required colour/wooden shade texture on wooden surfaces of any description, width or girth with following sequence:-(a) Cleaning and preparing the surface with rubbing of dand paper 80/120 no & 160/80 respectively.(b) Applying two coat of sealer with spray gun and allowing sufficient drying time for 1 st coat and 2 nd coat to dry for 8 to 12hrs. (c)On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excessive sealer lyer and make the surface smooth after this wet rubbing, then surface is applied with special grade melaminefillers to fill all the small & big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on whihc again alight wet to be alowed to dry for 4 to 6 hrs on whihc again a light wet rubbing is done and this surface is further allowed to dry for 12 hrs(d) On this suface 1st coat melamine polish is applied with soray gun using mealmine clear polish and melamine thinner in required porpotion. This 1 st coat is allowed to dry for 24 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete all as directed by Engineer-in-Charge (Final coat to be done in 1 or 2 layers without gap of time) |
| 32 | Supply & fixing 300 mm long brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled of drawn brass bolts and fixed complete all as specified and directed. |
| 33 | Supply & fixing of brass handles, cast type, polished bright of size 125mm complete all as specified and directed. |
| 34 | Supply & fixing of floor door stopper of brass body and tongue with hard drawn steel spring with overall length of cover plate 150 mm, fixed in floor complete all as specified and directed. |
| 35 | Supply & fixing Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed of size 150mm fixed in positions complete all as specified & directed. |
| 36 | Supply & fixing 125mm long Butt hinges, heavy weight, cold rolled extruded Brass with mild steel Butt hinges, extruded brass, with mild steel hinge pin, bright polished complete all as specified and as directed. |
| 37 | Supply & fixing 4 mm thick ordinary quality sheet glass pane area exceeding 0.50 Square metre in Each pane with necessary fittings like rubber bedding, glazing clips etc complete all as specified and directed. Please Enable Macros to View BoQ information |
| 38 | Supply & fixing 4 mm thick ordinary quality sheet glass pane area exceeding 0.50 Square metre in Each pane with necessary fittings like rubber bedding, glazing clips etc complete all as specified and directed. Please Enable Macros to View BoQ information |
