|
| 1 | DESCRIPTION OF ITEMS |
| 2 | M & L precast cement concrete Block Masonary with solid blocks type C1 1:3:6 20mm graded stone aggregate exc 10cm in width and setting in mortar 1:6 including Demolition of brick work,PCC Block or stone/boulder masonary built in cement mortar/lime mortar including all quoins, arches, pillars etc complete all as spd and directed |
| 3 | Demolition of brick work,PCC Block or stone/boulder masonary built in cement mortar/lime mortar including all quoins, arches, pillars etc complete all as spd and directed |
| 4 | Demolition of cement concrete as in ground floor and paving n.exc 15cm thick below or above ground level complete all as specified & directed. |
| 5 | M&L for 75mm thick PCC 1:2:4, type B-2, as in pavings/hard standing/path etc finished uneven and rough without using extra cement complete all as specified & directed. |
| 6 | M&L for 25mm thick rubber moulded coloured finish chequered cement concrete tiles of approved size , set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified & directed. |
| 7 | M& L for providing precast cement concrete rubber moulded coloured interlocking tiles 60 mm thick with grey cement and no pigment of approved design and pattern laid over a layer of 25 mm thick sand cushion including filling the joint with sand complete all as specified and directed |
| 8 | Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, Including removal of debries out side MOD land complete all as specified and directed. |
| 9 | M&L for rendering 15mm thick on brick or concrete surfaces in CM (1:6) used on fair faces of brick work or concrete surfaces of wall finished even and fair complete all as specified and directed. |
| 10 | M&L for rendering 15mm thick in cement mortar 1:4 on external wall using water proofing compound as per manufacture instruction on fair faces of brick work or concrete surfaces and finish the surface even and fair complete all as specified and as directed. (WPC shall be measured and paid seperatly) |
| 11 | M&L for rendering 10mm thick in CM (1:3) on ceiling surfaces finished even & smooth without using extra cement complete all as specified and directed. |
| 12 | M&L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion white or tinted with roller, over one coat of primer complete all as specified and directed. |
| 13 | M&L for preparation of new surface of walls (external surfaces) and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) , as per manufactures instructions etc complete all as specified and as directed. |
| 14 | M&L for prepration of new plastered ceiling surfaces and applying three coat of white washing complete all as specified and directed |
| 15 | Supply only water proofing compound. |
| 16 | M&L Complete removal of existing treatment on wall/roof projections including facia,cornices etc by scrapping with mechanical sander(having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust,loose paint etc by skilled labour complete all as specified and directed. |
| 17 | M&L for old plastered surfaces of walls and applying two coats of distemper oil emulsion white or tinted with mechanical means, over complete all as specified and directed. |
| 18 | M&L for preparation of old plastered surfaces of walls and applying one coat of distemper oil emulsion white or tinted with mechanical means,incl repair of holes and cracks complete all as specified and directed. |
| 19 | M&L for preparation of old plastered surfaces of Ceiling and applying one coat of distemper oil emulsion white or tinted, complete all as specified and directed. |
| 20 | M&L for preparation of old painted surfaces of any description over 10cm girth or width,not otherwise described and applying two coats of Plastic emulsion paint complete all as specified and directed.Note:- Plastic emulsion paint to be applied through mechanical means only. |
| 21 | M&L for old surfaces and applying two coats of exterior emulsion paint with one coat of primer in normal pattern as per manufacturers instructions etc complete all as specified and directed by Engr-in-charge. Note :- Primer and emulsion to be carried out through air less spray machine (Mechanical means) |
| 22 | M&L for preparation of old surfaces and applying One coats of exterior emulsion paint in normal pattern as per manufacturers instructions etc complete all as specified and directed by Engr-in-charge. Note:- (1) Primer and emulsion to be carried out through air less spray machine (Mechanical means).(2) repair of pot holes, cracks and undulation in surface with wall care putty as required. |
| 23 | M&L for providing & applying average 1mm thick of Birla/ JK wall care putty over prepared surface to achieve the surface even and smooth for painting, complete all as specified and as directed |
| 24 | M & L for preparation of old decorated surfaces of walls (plastered or unplastered) and cornices, by brooming down , scrapping down smoke soot, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of white wash on walls complete all as specified and directed. Note:- All pot holes/cracks to be filled. |
| 25 | All as per item above here in before but on ceiling surfaces one coat complete all as specified and directed. |
| 26 | M&L for applying one coat of synthetic enamel paint including preparation of old steel surfaces of any description over 10cm width or girth all as specified. |
| 27 | M&L for applying one coat of synthetic enamel paint including preparation of old painted wooden surfaces of any description over 10 cm width or girth all as specified. |
| 28 | M & L for preparation of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed. |
| 29 | M & L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified & directed. |
| 30 | S & F in repairs 600 x 450 mm beveled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers (In repairs) complete all as specified & directed. |
| 31 | S & F in repair PVC cabinet mirror size 350mm x 450 mm fixed with steel screws with rowel plug complete all as specified and directed |
| 32 | S & F rotational moulded polyethylene three layered water storage tanks 500 Litres capacity (cylindrical, vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I including taking down existing water tank complete all as specified & directed. |
| 33 | S & F rotational moulded polyethylene three layered water storage tanks 1000 Litres capacity (cylindrical, vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I including taking down existing water tank complete all as specified & directed. |
| 34 | S & F (in repair) 15 mm bore fancy type bib taps brass chromium plated screwed down, screwed for iron pipe or for brass ferrule including flench complete all as specified & directed. |
| 35 | S & F (in repair) 15mm bore pillar taps, brass chromium plated, screwed down high pressure with or without lettered, hot or cold with long screwed shanks and fly nuts, screwed to iron pipe complete all as specified & directed. |
| 36 | S & F (in repair) 15 mm dia chromium plated angle cocks/stop valves, brass, screwed down, high pressure with crutch or butterfly handle, flench screwed both ends for iron pipe or for union complete all as specified & directed. |
| 37 | S & F (in repairs) 15 mm bore concealed stop cock, chromium plated, cast copper alloy, screwed down with crutch or butterfly handle screwed both ends complete all as specified & directed. |
| 38 | S & F in repairs 20 mm bore PTMT ball valves, high pressure with polyethylene float and fly nuts complete, screwed for iron pipe or for brass ferrule complete all as specified & directed. |
| 39 | S & F in repairs bottle trap of PTMT having minimum water seal of 25mm (Minimum weight 32mm-260gms) |
| 40 | S & F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long. (Cat No. F5001114 or equivalent) |
| 41 | S & F in repairs vitreous china squatting pan of ‘Orrisa pattern’ size 580x440mm, white with integral foot rest including replacement of ‘P’ or ‘S’ trap, lime concrete bedding and making good floor complete all as specified and directed. |
| 42 | S & F in repair vitreous china wash down water closet pan (pedestal pattern), white, including plastic seat cover and flushing pipe complete all as specified & directed. |
| 43 | S & F in repairs PVC low level flushing cistern 10 Litre capacity, symphonic action type, white as approved including ball valve, float valve and handle, flush pipe complete all as specified & directed. |
| 44 | S & F in repairs vitreous china wash hand basin, white, size 550 x 400 mm including brackets, chromium placted waste coupling &PVC waste pipe of 32 mm dia complete all as specified & directed. |
| 45 | S & F in repairs 600mm long PVC connection, 15 mm bore complete all as specified & directed. |
| 46 | S&F in repair CP brass wall mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15mm bore complete all as specified and directed. |
| 47 | S & F in repair CP towel rail 600 mm long as a approved quality complete all as specified & directed |
| 48 | S & F in repairs 20 mm dia gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified & directed |
| 49 | S & F in repair plastic water closet seat cover closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device |
| 50 | S&F in repairs for Brass chromium plated waste couplings of dia 32 mm for WHB fixed complete all specified and directed |
| 51 | S&F in repairs 40 mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed |
| 52 | S&F in repairs aluminium peg set of Six complete all as specified and as directed. |
| 53 | Cutting Chases for concealed water tubing,shelves,chajjas,sunshades etc and making good disturbed surfaces, cutting not exceeding 10 cm girth, on brick walls complete all as specified & directed. |
| 54 | Taking up or down steel tubing and connections 15 mm bore pipe and removing from site complete all as specified & directed. |
| 55 | Taking up or down steel tubing and connections 20 mm bore pipe and removing from site complete all as specified & directed. |
| 56 | S & F 15 mm bore tubes, medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified & directed. |
| 57 | S & F 20 mm bore tubes, medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified & directed. |
| 58 | Refixing of 15 mm dia old steel tubing and connections in new or old position (Walls, ceilings, floors etc) |
| 59 | Refixing of 20 mm dia old steel tubing and connections in new or old position (Walls, ceilings, floors etc) |
| 60 | S & F in repair Kitchen plate rack of stainless steel of size 720mm x 600mm x 230 mm made out of 1 mm thick steel sheet complete all as specified & directed. |
| 61 | S & F in repairs stainless steel sink with draining board, made out of 1mm thick steel sheet for kitchen with waste pipe, CI cantilever brackets, connecting union overall size 915 x 460mm with bowl size 410 x 330 x 160mm complete all as specified & directed. |
| 62 | S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm all as spd and directed |
| 63 | Providing water proofing treatment to RCC sunken slab as specified and directed as under:- (a) Cleaning the existing RCC sunken slab and vertical wall/RCC beam and hacking the surface. (b) 15mm thick plastering over the floor & vertical surface in CM 1:4, mixed with liquid water proofing compound @ 200ml per 50 kg of cement trowelled to even and smooth finish without using extra cement .. (c ) filling the sunken portion with water for 72 hrs and carring out the ponding test.(Any leakage /seapage noticed shall be repaired). (d) Applying two coats of elastomaric acrylic water proof coating Make: Dr. Fixit of pidilite or equivalent per sqm in each coat with roller application.(Note: Each coat of elastomaric acrylic compound requires 6-8hrs to dry up itself second coat shall be applied on getting the first coat completely dried up.) |
| 64 | S & F in repairs PVC floor trap 75 mm bore including jointing to waste pipe in cement mortar complete all as specified & directed. |
| 65 | S & F in repairs 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls/floors with necessary fittings complete all as specified & directed. |
| 66 | S & F in repairs PVC (SWR) bends 110 mm bore complete all as specified & directed. |
| 67 | S & F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls/floors etc complete all as specified & directed. |
| 68 | S & F in repairs 75 mm bore PVC (SWR) bends complete all as specified & directed. |
| 69 | S & F in repairs 40 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls/floors etc complete all as specified & directed. |
| 70 | S & F in repairs 40 mm bore PVC (SWR) bends complete all as specified & directed. |
| 71 | M&L 4 mm thick E board tiles for insulation and accoustic purpose 60X60 cm with and including powder coated galvanium iron snap grid with 15X15X1.5 mm thick tee section and 32X25X1.5 mm thick angle section with all hanging /sopporting arragements as in false ceilling incl taking down old ceiling with frame and making good disturbed surface complete all as specified and directed . |
| 72 | M&L for repair to leadage /sepage from 'J' Hooks of CGI /AC/Galvalume roof sheets by replading cup washer and bitumen washer including necessary T & P complete all as specified and directed. |
| 73 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) n.exc 1.50 Sqm each complete all as specified & directed. |
| 74 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.50 Sqm and n.exc 4.00 Sqm each. complete all as specified & directed. |
| 75 | Taking down shutters of any description exc. 1 Sqm & n.exc 2 Sqm each complete all as specified & directed. |
| 76 | Taking down shutters of any description not exc. 1.00 Sqm each complete all as specified & directed. |
| 77 | Refixing of shutters of any description exc 2 Sqm each in same opening including taking down, easing and adjusting and also refixing builders hardware as required |
| 78 | Refixing of shutters of any description exc 1 Sqm but n.exc 2 Sqm each in same opening including taking down, easing and adjusting and also refixing builders hardware as required |
| 79 | S & F of second class soft wood (Sal) as in plain, solid , straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified & directed. |
| 80 | S & F wiremash door pvc providing 30mm thick factory made wire mesh solid pvc door shutter consisting of frame made out of M.S. Tubes of 19 gauge thickness and size of 19mm X 19mm for stiles and 15mm X 15mm for top , lock and bottom rails. M.S. Frame shall have a coat of metal primer of approved make and manufacturer 19mm X 19m M.S. square tubes shall be covered with heat moulded plain sheet ' C' channel made from 5mm thick PVC sheet manufactureed by an ISO-9001-2008 certified company , of size 30mm thickness and 90 mm width out of which 75mm shall be flat and 15mm shall be bent in 90 degree angle on either side forming stiles, one of the 90 degree bend edge is cut from stiles as well as rails to nails from inner side of door to hide wire mesh fixing steel screws. 5mm thick 115m wide PVC sheet out of which 100 mm shall be flat and 15 mm shall be bent in 90 degree on the inner side to form top and bottom rail and 130 mm wide pvc sheet out of which 100 mm shall be flat and 15mm shall be bent in 90 degree on both side to form lock rail . An additional 5mm thick pvc strip of 20 mm width is to be stuck on the interior side of the 'C' channel using pvc solvent cement adhesive. panel will be of SS wire mesh of 24 gauge and 1.4 mm aperture to be fitted inside area of stiles and rails. The wire mesh in top , bottom, and lock rail is sealed with 15mm X 15mm tube with steel screw of size 13/6 mm. 10mm thick (5mmX2nos) thick pvc strip of 25 mm width is to be stuck & nails on Both side of G.I. wire mesh interior at the top , bottom &lock rail. 10 mm thick (5mmX2nos), 20mm wide cross PVC sheet as gap insert for top rail & bottom rail door to be fixed to frame with 3nos. M.s powder coated butt hinges size 100 mm X 25mm X 2mm and 32 mm long steel screws drilled suitable to pass throug both the walls of the M.S. tube other hardwares should be fixed with 19X6mm size steel screws etc. complete all as specified and directed. |
| 81 | S & F 35mm thick second class hard wood glazed and skeleton door shutters (three panels), open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framming plain, chamfered or rounded fitted with cut and mitred beads or securing glass etc, size of members of shutters all as per clause No 8.20 (a) of SSR Part-I (2009). |
| 82 | S & F 28-30 MM mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on both side complete all as specified & directed. |
| 83 | S & F in repairs 3mm thick pin headed figured glass, ordinary quality, glazing with oil putty or fixed with wooden beads in steel/wooden windows in squares n.exc 0.50sqm each pane at any floor/hight complete all as specified & directed. |
| 84 | S & F in repairs 3mm thick pin headed ground or obscured or frosted, on one side, ordinary quality, glazing with oil putty or fixed with wooden beads in steel/wooden windows in squares n.exc 0.50sqm each pane at any floor/hight complete all as specified & directed. |
| 85 | M & L solid PVC door frames of size 50mm X 47 out of 5mm wood grain printed PVC sheets reinforced with MS Square tube supplying and fixing in openings as per manufacturers instructions. |
| 86 | S & F factory made hollow PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded wood grain print PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for tp rail & bottom rail, panelling of wood grain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to geter with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 87 | M&L providing factory made PVC internal door frame (PRELAM ) of size 100 mm x 45 mm with a wall thickness of 5 mm (+- 0.25 mm) made out of extruded 5 mm (+-).25 mm) thick PVC sheet manufactured by an ISO 9001-2008certified company and by joining 3 nos of heat bend PVC sheet section The inside section of size 90 x 30 mm shall be made from plain colour PVC sheet of 5 mm (+- o.25 mm) thickness the inside section will be covered by sticking two sections of size 30 x 35 mm and 70 x 45 mm made from (+-0.25 mm) thick plain PVC sheet The frame shall be mitered cut at two corners and joined with 4 nos of 150 mm longbrackets of 15 mm x 15 mm MS square tube The two vertical door frame are tobe reinforced with 40 mm x 20mm MS square tube of 19 guage through out the frame the door shall be fixed to the wall using anchor fastners A minimum of 4 nos of screw to be provided for each vertical members and min 2 nos for horizontal members etc complete as per manufacturers specification and direction of engineers-in-charge |
| 88 | M&L in providing 30 mm thick factory made internal PVC flush door shutter wood free consisting of frame made out of MS tube of 19 guage thickness and size 20 mm x 40 mm for stiles as well as top bottom and lock rail MS frame shall have a coat of primer of approved make and manufacturer The inside Panel shall consist of 20 mm thick multichamber hollow PVC section 1 mm thick wall thickness bonded using solvent cement/ cynoacrylate adhesive with 5 mm (+-0.25 mm ) thick plain / prelam PVC sheet manufactured by an ISO 9001-2008 certified company on both side of the inside panel ALl the four edged lipping to pe painted with PVC ink of matching colour of PLAIN/PRELAM moulded PVC sheet of door 0.20 mm thick (5 mm x 4 mm ) thick PVC sheet to be given for lock provision at lock height door to be fixed with frame with 3 nos SS butt hinges of size 100 mm x 25 mm x 25 mm and 50 mm long steel screw drilled suitable for to pass through both the wall of th MS tube other hardwares could be fixed with 25 mm x 8 mm size steel screw etc complete as per direction of engineer in cahrge manufacturer specification and drawings |
| 89 | S&F in repairs factory made PVC Cupboard frame of the size 75mm x 40mm with a wall thickness of 5mm, made out of extruded 5mm thick plain/prelam PVC sheet of density 600 kg/cbm, having bottom width of 50mm and thickness of 10mm. All four frame lengths reinforced with 15 mm x 15mm M. S. square tubes of 19 gauge thickness throughout the frame and mitre cut at two corners adjointed with 2 nos. of 15mm long brackets 0f 10mm x10mm M S square tubes. The door frame shall be fixed to the wall using 8/100 long M S screws through the frame by using PVC fasteners. A minimum of 4 nos. of screws to be provided for each vertical member and minimum of 2nos. of screws to be provided horizontal member etc. complete as per direction of Engr-in-Charge, manufacturer's specification and drawing. |
| 90 | S&F factory made PVC cupboard flush type shutter of 30mm thick consisting of frame made out M S tubes of 19 gauge thickness and size 19mm x 19mm for stiles and rails. The inside panel shall consist of 20 mm thick multichamber hollow PVC section of 1mm wall thickness, bonded using solvent cement/ cynoacrylate adhesive with 5mm thick plain/prelam PVC sheet, on both side of inside panel incliding necessary items to fix the shuter to frame such as 100mm stailess steel hinges, 100 mm long handles made of anodised aluminium and magnetic ball catch for each pair of shutter.All four edges of the panel to be sealed with lipping of 10mm thick and 20mm wide PVC sheet baton (made by sticking 2nos. PVC foam sheet of 5mm thickness using PVC solvent cement adhesive). complete as per direction of Engr-in-Charge. |
| 91 | S&F in repairs PVC boards 19/20 mm thick any colour as in cabinets incl sshelves and shutters, fixed with screws and adhessive as per direction of Engr-in-Charge and, manufacturer's instructions including piano hinges, magnet catcher, handles etc. |
| 92 | S&F mild steel work as in bands, straps, hold fast, wall ties, hooks for hanging fans, angle cleats & similar small articles conforming to Fe-410-0 or Fe-310-0 complete all as specified & directed. |
| 93 | S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.4 mm complete all as specified & directed. |
| 94 | S & F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.4 mm complete all as specified & directed. |
| 95 | S&F for Pressed steel frames for doors (125X60mm) with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified directed |
| 96 | S&F for Pressed steel frames for doors (105X60mm) with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified directed |
| 97 | S&F in repairs 300 mm long mild steel sliding door bolt plate type stove enameled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified & directed. |
| 98 | S&F continous (piano) hinges mild steel 30mm width of flaps ,bright fuinish or electrogalvanised complete all as specified and directed. |
| 99 | S&F aluminium anodized barrel tower bolts 150mm long, of extruded section complete all as specified & directed. |
| 100 | S&F aluminium handles 125 mm long, cast type, anodized complete all as specified & directed. |
| 101 | S&F 250mm Aluminium alloy anodised sliding door bolts with hasp,staple(bolt type)and fixing clips of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded section or aluminium alloy and fixed. |
| 102 | S&F Anodised aluminium powder coated (minimum thickness of powder coating 50 micron) window , ventilator shutters and kitchen cupboards, side hung type/ slidding type/Louvered Ventilator without sash bars, alumimium section weighing 0.55 kg/m including necessary joining cleats glazing clips, ruber packing, anodised aluminium snap beading screws anodised aluminium fittings such as ped stays 150mm long (1 No) hinges type B-21 100mm long (2 No) suitable handle (1 No) complete all as specified. |
| 103 | S&F Anodised aluminium powder coated (minimum thickness of powder coating 50 micron) frame and shutter for doors and frame for windows, ventilators and kitchen cupboards frame with one or more rebates including joining cleat for fixing etc. complete all as specified. Please Enable Macros to View BoQ information |
| 104 | S&F Anodised aluminium powder coated (minimum thickness of powder coating 50 micron) frame and shutter for doors and frame for windows, ventilators and kitchen cupboards frame with one or more rebates including joining cleat for fixing etc. complete all as specified. Please Enable Macros to View BoQ information |
