|
| 1 | Demolition of reinforced cement concrete of any description ad in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed. |
| 2 | Material and Labour for reinforced cement concrete 1:2:4 type B1 using 20mm graded granite stone aggrgate as in Columns, pillars, piers, posts and struts and the like complete all as specified and directed. Note : Reinforcement and form work shall be measured and paid separately. |
| 3 | Dismantling floor, hearth or wall tilling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 4 | Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 5 | Material and labour for 40mm thick plain cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in as in leveling course including use of form work as necessary complete all as specified and as directed. |
| 6 | Material and Labour for 75mm thick Plain Cement Concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection, floors, pavings and hardstanding etc, finished even smooth without using extra cement etc including necessary forwork, complete all as specified and as directed. |
| 7 | Dismantling wrought iron or mild steel work of any description not otherwise specifically provided for complete all as specified and as directed. |
| 8 | M&L Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed. |
| 9 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed. |
| 10 | S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering /cladding to wall, fixed with self tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified. |
| 11 | S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering /cladding to wall, fixed with self tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified. |
| 12 | M&L for MS work as in Wind Tie in roof and MS structural works in trusses, etc with screwed ends including nuts, washers and mild steel plates for walls chimneys, roofs arches etc any kind rods and straining bolts conforming to Fe 410-0 or Fe 310-0 complete all as specified . |
| 13 | Material and Labour for vitrified ceramic tiles 8-10 mm thick polished area of each tiles not exceeding 0.36 sqm of any shade and any pattern (pattern consists combination of two or more tiles ) as in skirting etc jointed in neat cement slurry and pointed in colored cement to match colour tiles over and including 15mm thick screed bed in CM 1:6 and pointed in coloured cement to match coloured tiles complete complete all as specified and as directed. . Note:- (i) The colour, shade and pattern shall be approved by the GE during execution work. (ii) No extra cost shall be allowed for Removing and refixing and necesary cutting of door etc if any required during execution of work. |
| 14 | M&L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match ,light shade, incl 15 mm thick rendering in CM (1:6) complete all as specified and directed. |
| 15 | M&L for digital design glazed ceramic coloured tiles in vertical surface of size of each tile 300 x 450 mm /350x250 mm and 7 to 8 mm thick fixed to set and joint in neat cement slurry and pointed in white or coloured cement to match the same complete all as specified and directed. |
| 16 | Taking down cement plastering on concrete or Brick works surface racking out joints, hacking for key , scrubbing down with water, removing rubbish/debris etc complete all as specified and as directed. |
| 17 | Material and labour for rendering 10mm thick in Cement Mortar 1:6 on fair faces of brick walls or on concrete surfaces, finished even and smooth,without using extra cement complete all as specified and directed. |
| 18 | Material and labour for 15 mm thick rendering on brick/concrete surfaces in two layers in CM 1:4, finishing coat of 5mm thick, finished even and smooth without using extra cement complete all as specified and as directed. |
| 19 | Material and Labour for rendering 5 mm thick in cement mortar 1: 3 on fair faces of concrete surfaces of ceiling finished even and smooth with out using extra cement, complete all as specified. |
| 20 | Material and labour for preparation of of new plastered/concrete surfaces of walls and applying two coats of acrylic distemper of approved shade/tint over a coat of primer, over surface of wall all as specified and as directed. |
| 21 | Material and labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 22 | Material and labour for preparation of of new plastered/concrete surfaces of ceiling and applying two coats of acrylic distemper of approved shade/tint over a coat of primer, over surface of wall all as specified and as directed. |
| 23 | M&L for complete removal by Washing, rubbing down and stopping and preperation of distempered and painted surfaces of walls, pillars,cornices by brooming down etc including filling depressions of scrapped surfaces with wall care putty (1 mm thick) and preparation of surfaces for further treatment and applying two coats of distemper oil emulsion over a coat of primer complete all as specified & directed. |
| 24 | Material and labour for complete removal by Washing, rubbing down and stopping, preparing old external plaster surface of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 25 | Material and Labour for TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking,bending spirally for hooping ,for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 26 | M&L mild steel TMT bars 5mm dia and over up to 10mm for stirrups cut to length , bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia bars confirming to Fe-410-S or Fe-410-0 complete in all respect as specified and directed. |
| 27 | Supply and fix in repairs PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed. |
| 28 | S&F in repairs Waste coupling of PTMT (half or full threaded) . (Minimum weight of 32mm -45gms/ 40mm-60 gms) |
| 29 | Supply and fixing in repairs PVC waste pipe 32mm dia with 40mm dia reducer, 90cm long for WHB/urinal outlet with 4 Nos screws for fixing pipes, complete all as specified and directed. |
| 30 | Taking up or down steel tubing 20 mm bore including connections, cleaning for refixing or removal to store all as directed. |
| 31 | Supply and fixing galvanised steel water tubing medium grade 20 mm bore including all necessary fittings such as bends, L bows, short piece connections, backnuts, caps plugs, unions couplings, flanges, sockets etc, fixed to wall/floor/ceiling including necessary cutting/chauging in walls made of brick/concrete surface complete all as specified and as directed. |
| 32 | Taking up or down steel tubing 15 mm bore including connections, cleaning for refixing or removal to store all as directed. |
| 33 | Supply and fixing galvanised steel water tubing medium grade 15 mm bore including all necessary fittings such as bends, L bows, short piece connections, backnuts, caps plugs, unions couplings, flanges, sockets etc, fixed to wall/floor/ceiling including necessary cutting/chauging in walls made of brick/concrete surface complete all as specified and as directed. |
| 34 | Taking down existing unserviceable water tank after disconnecting water supply line and Supply and fix Rotational moulded Polyetheylene Water Storage Tank 500 Ltr capacity Triple Layer (Cylinderical verticle with closed top) including 20mm dia GI Medium Grade 450mm long overflow and wash out pipe each with all required fittings, Checknut, Stopper etc complete hoisted and fixed in position, including all incoming and outgoing connection of GI pipe complete and including 25mm PTMT Ball valves high pressure wiith epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete for 20mm dia pipe fixed on roof top complete all as specified and directed. |
| 35 | S&F in repairs Vitreous china wall/floormounted western toilet/commode, square/oval type deat in built in single pices European type water closet with flushing cistern, seat cover of size 780 x 375 x 700 mm, white complete including ‘P’ or ‘S’ trap , brackets, flushing pipe etc, complete all as specified.Make:Cera/Parryware/Hindware |
| 36 | Supply and Fix in repairs vitreous china wash down water closet Pedastal pattern white (excluding flushing cistren ) including trap set, seat cover and fixing of flushing cistern, brackets, flushing pipe etc, etc. with 'P' or 'S' trap, making good the floor to match with existing floor complete all as specified and as directed. |
| 37 | Supply and fix in repair 10 Ltr capacity PVC valveless, syphonic action type, flushing cistern low level, white, with inlet ball valve, float and handle including brackets, flushing pipe, 450mm long PVC Connection and connection to trap, and to flushing and making good to floor complete all as specified . |
| 38 | Supply and fixing in repairs vitreous China wash hand basin, white (flat back or angle back type or counter top) of size 600X480mm including 32mm brass chromium plated waste fitting, a pair of cast iron bracket duly painted including cutting and pinning in ends making good disturbed surfaces in CM 1:3 excluding pillar tap but chain , plug and porcelain stopper, brackets etc all as specified and as directed. |
| 39 | Supply and fixing in repairs Vitreous China full stall urinal bowl type (back or corner wall type), white , of size 465mm x 355mm x 265mm complete with chromium plated waste fittings including providing and fixing plugs,bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing arround urinal back in cement, (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) all as specified and as directed. |
| 40 | Supply and fixing in repairs 6 mm thick bevelled edge looking mirror of size 600 x 450 mm mounted on 6 mm thick AC Building board or commercial plywood/hard board backing and fixed to wooden plugs with CP Screws and cup washers all as specified and as directed. |
| 41 | Supply and fix in repair fancy type 15mm dia pillar tap, cast copper alloy, chromium plated, with capstan head screwed down high pressure with or without lettered hot or cold with long screw shank and fly nutt screw for iron pipe Make: CERA /Parryware/Hindware |
| 42 | Supply and fix in repairs stop valves 15mm bore, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 43 | Supply and fix in repairs 15mm dia bib taps cast copper alloy fancy type chromium plated with crutch or butterfly handle screwed down , screwed for iron pipe or union complete all as specified and directed. |
| 44 | Supply and fix in repairs Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 15 mm bore complete all as specified and directed. |
| 45 | Supply and fix in repairs Angle valve CP cast copper alloy, with capstan handle, screwed down, high pressure screwed both ends for 15 mm bore iron pipe or for unions and fixed complete all as specified and directed. |
| 46 | Supply and fix in repairs 2 way angle valves/2 in 1 angle cock, 15mm bore,quarter turn with wall flange, chromium plated, screwed down, high pressure with crutch or butterfly handle and fixed complete all as specified and directed. |
| 47 | Supply and fix in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 48 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 49 | Supply and Fix Aluminium Composite Panel(ACP) cladding using 3mm thick ACP panel of approved colour jointed as per manufacturer's instruction, fixed to existing frame work by using aluminium blind rivets with ss screw, filling the joint and voids with high quality sealant (silicon gel) complete all as specified and as directed. |
| 50 | Supply and fix PVC wall panelling of surface laminated any pattern and any shape of 7 to 10mm thickness and any colour at any position inclusive of solvent cement and fixing at over a grid of PVC frame installed on the wall, which works as a base to install the PVC wall panels. Each panel have to interlock with each other complet all as per manufactures instruction complete all as specified and as directed by Engineer in Charge. |
| 51 | Supply and fix PVC Supply and fix for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame, complet all as per manufactures instruction complete all as specified and as directed by Engineer in Charge. |
| 52 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm each complete all as specified and as directed. |
| 53 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 sqm each complete all as specified and as directed. |
| 54 | Supply and fix powder coated (minimum thickness of powder coating 50 micron) aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, and sliding tower bolt 150mm long anodised aluminium snap beading, screws etc. complete all as specified and as directed. |
| 55 | Supply and fix aluminium powder coated (minimum thickness of powder coating 50 micron), frame for doors,windows, ventilators with one or more rebates with joint clip and using rubber beading etc complete all as specified and directed.Note : Glass panel/particle board panel filling shall be measured and paid separately. |
| 56 | S&F anodised aluminium window and ventilator shutter, side hung type type without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleat, glazing clips, rubber neoprene packing, anodised aluminium snap beading, scews anodised aluminium fittings such as peg stay 150mm long (01 No), hinges type B-21 100mm long (02 No) suitable handle (01 No) complete all as specified and as directed. |
| 57 | Supply and fix Powder Coated aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum coating of grade AC 15) of DG 102 design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved aluminium standard section around the opening, all complete as per requirement complete all as specified and directed. |
| 58 | Supply and fixing aluminium alloy,anodised, sliding door bolt of length 250mm with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded section or cast-aluminium alloy complete all specified and as directed. |
| 59 | Supply and fixing floor door stopper aluminium alloy body and tongue, anodised with hard drawn steel spring, 150 mm over all length of cover plate complete all as specified and as directed. |
| 60 | S&F aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of operature 1.40mm and fixed with aluminium wire staples |
| 61 | Supply and Fixing 5.5mm thick glass, ordinary quality and glazing with oil and putty in square not exc 0.5 sqm in each pane complete all as specified and as directed. |
| 62 | Material and Labour for pre-laminated particle board 12 mm thick, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with rubber beading and screws as in aluminium works etc complete all as specified and directed. |
| 63 | S&F aluminium (Die cast body) Door closer hydraulically regulated, designation No 2, universal type, suitable for door shutters 701 to 850mm in width and of weight between 36 ro 60 Kg complete all as specified and as directed |
| 64 | Supply and fix anodised aluminium snap grid frame work for false ceiling with 605mm x 605mm size, consisting of main Tee of size 40 x 40 x 2mm, cross Tee of size 40 x 40 x 2mm and wall angle of size 40 x 40 x 2mm of approved make including all necessary cuttings, fixing of aluminium section firmly in position with and including steel hangers 6 mm dia G.I. wire (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansion hold fasteners 40 mm long in soffit of slab/walls complete all as specifed and as directed including provision of with 4mm thick Non Asbestos boards, ordinary type for fixing in 600 mm x 600mm grid, fixed in ceiling, flat or sloping, complete all as specified and directed.Note :- Rate quoted above shall be deemed to include for making holes, cutting chassis if any required and making good to existing walls in cement mortar 1: 3 to match with existing surface finish as directed at site. |
| 65 | Supply and fixing stainless steel letters polished to glossy finish, letter size of exceeding 10cm and not exceeding 25cm hight and not exceeding 10cm width and 1.6mm thick fixed on ACP sheet cladding with approved adhesive/ necessary fixing arrangement in Hindi/ and English complete all as specified and as directed. |
| 66 | Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators sockets etc. to be measured separately), removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors, etc. |
| 67 | M&L point wiring complete with 1.5 Sqm sincle core PVC insulated unsheathed FRLS cable 1100 volts grade (ISI marked) with multi stranded copper conductor drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI) marked concealed in wall/fixed to roof, ceiling etc and incl provn of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FRLS (ISI marked) as earth continuity conductor, fabricated sunken terminal box made out of 1.60 mm thick sheet steel duly painted concealed in walls, with 3mm thick bakelite/PVC sheet ISI marked top cover with brass/chromium plated screws and cup washers for housing switches, socket outlets, fan regulators etc, all as specified and as directed for the following :- (a)One light point or one light/ exhaust fan/ fan point controlled by one switch with cables 1.5 sqmm size |
| 68 | Supply and fixing in replacement of LED Panel square of size 600 x 600mm, slim compact, IRIS surfaces mounted downlight fixture panel fitting 40 watt, 220 V AC with high efficiency opal diffuser for soft glare free even light distribution with electronic driver, connecting up with Driver three core flexible copper conductor cable and fixture, complete all as specified and directed by Engr-in-Charge.Make-Havells/Philips/Bajaj/Crompton. |
| 69 | Supply and fixing in replacement of LED Panel Square of size 600 x 600mm, slim compact, aluminum die cast edge LED recess mounted downlight fixture panel fitting 40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free even light distribution with driver suitable for roof ceiling, connecting up with Driver three core flexible copper conductor cable and fixture, complete all as specified and directed by Engr-in-Charge.Make-Havells Model No. LHEBAEP7IZ1W040 or equivalent in Philips/Bajaj/Crompton. |
| 70 | Supply and fixing in replacement of LED Panel square, slim compact, IRIS surfaces mounted downlight fixture panel fitting 18 watt, 220 V AC with high efficiency opal diffuser for soft glare free even light distribution with electronic driver, connecting up with Driver three core flexible copper conductor cable and fixture, complete all as specified and directed by Engr-in-Charge.Make-Havells/Philips/Bajaj/Crompton. |
| 71 | Supply and fixing in replacement of LED Panel Square, slim compact, aluminum die cast edge LED recess mounted downlight fixture panel fitting 18 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free even light distribution with driver suitable for roof ceiling, connecting up with Driver three core flexible copper conductor cable and fixture, complete all as specified and directed by Engr-in-Charge.Make-Havells / Philips/Bajaj/Crompton. |
| 72 | Supply and fixing in replacement of LED light fitting 45 watt street light for building security lights, 230 Volts, outdoor type & Wide temperature operating range: -10 °C to +50 °C, with best in class design & roubst heat sink for better heat dissipation, electronic driver unit with IP 65/66 protection,lamp bracket with impact and corrosion resistant including two coat of silver coloured Mild steel angled pipe of suitable size for fixing of security light, necessary mounting bolts, nuts and washers, fixing on iron angle complete all as specified and directed by Engr-in-charge.Make: Crompton/Philips/Bajaj/Havells. |
| 73 | Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc, and cutting chases for concealed conduit wiring and making good, cutting not exc 10 cm girth,& as per site reqirement. complete all as specified and directed by Engineer in charge. |
| 74 | Supply and fix Distribution board (DB) made out of sheet metal enclosure (CRCA sheet), dust and vermin proof, TPN 8 way with 200 Amps rated copper bus bar double door protection, neutral bar,earth bar, triple pole and neutral 415 volts,MCBs used as incommer Double door, flush to wall complete all as specified and as directed. |
| 75 | Supply & fix MCB SPN 40-63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of single pole in the MCB DB complete with connection testing and commissioning complete all as specified and directed. Make: Indo Asian/ L&T/Crompton Greaves/Havells |
| 76 | Supply & fix MCB SP 6-32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of single pole in the MCB DB,IP 20 transparent lebel holder fully insulated safety shutters suitable for cable up to 35 Sqmm cross sectional area complete including suitable size copper Lugs complete all as specified and directed. Make: Indo Asian/ L&T/Crompton Greaves/Havells |
| 77 | Supply & fixing Distribution board (DB) made out of sheet metal enclosure (CRCA sheet), dust and vermin proof, SPN 8 way with 200 Amps rated copper bus bar double door protection, neutral bar,earth bar, single pole and neutral 240 volts, MCBs used as incommer flush to wall complete all as specified and as directed. |
| 78 | Material and labour for Sub main wiring using two runs of single core PVC insulated cable (FR) 6 sqmm copper conductor multi stranded and one run of 6 sqmm copper conductor insulated cable (FR)using as earth wire drawn through and including suitable size PVC casing caping including taking down old aluminium/Copper Sub main wirng complete all as specified and directed. Note- 3 run of 6 sq mm PVC copper wire and One run of PVC casing caping shall be measured and paid as one unit. |
| 79 | Material and labour for Sub main wiring using two runs of single core PVC insulated cable (FRLS) 4 sqmm copper conductor multi stranded and one run of 4 sqmm copper conductor insulated cable (FRLS)using as earth wire drawn through and including suitable size casing capping including taking down old aluminium/Copper Sub main wirng, complete all as specified and directed. Note- 3 run of 4 sq mm PVC copper wire and One run of PVC casing caping shall be measured and paid as one unit. |
| 80 | Supply & fixing Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 32 X 6 mm by means of nut, bolts, check nuts and washers of galvanised iron or steel and provision of charcoal dust and common salt packed all around the earth plate including necessary excavation and earth work in any type of soil and testing complete all as specified and directed and shown in electrical plate number 3 of MES SSR part-I(2009)Note: Unit rate quoted shall be deemed to be included the following (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 40 mm nominal bore medium grade GI protection pipe 7.5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing. Please Enable Macros to View BoQ information |
| 81 | Supply & fixing Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 32 X 6 mm by means of nut, bolts, check nuts and washers of galvanised iron or steel and provision of charcoal dust and common salt packed all around the earth plate including necessary excavation and earth work in any type of soil and testing complete all as specified and directed and shown in electrical plate number 3 of MES SSR part-I(2009)Note: Unit rate quoted shall be deemed to be included the following (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 40 mm nominal bore medium grade GI protection pipe 7.5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing. Please Enable Macros to View BoQ information |
