|
| 1 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area not exc 1.5 Sqm each and removing from the site including making good the disturbed surfaces of wall etc to match with existing adjoining surfaces complete all as specified and directed. |
| 2 | All as per Item No 01 above, but exc 1.5 sqm but not exc 4 sqm each complete all as specified and directed. |
| 3 | Taking down shutter of any description not exc 1 Sqm and removing from site complete all as specified and directed. |
| 4 | All as per ser item No 03 above, but area exc 1.00 Sqm and not exc 2 Sqm each complete all as specified and directed.. |
| 5 | Resecuring or easing and adjusting with out taking out of wooden shutters not exc 1 Sqm and complete all as specified and directed. |
| 6 | All as per ser item No 05 above, but area exc 1.00 Sqm and not exc 2 Sqm each complete all as specified and directed. |
| 7 | M&L 2nd class hard wood plain solid straight chowkhat or frame, wrought, framed, rebated on the solid, put together with glue and pinned at joint complete all as specified and directed. |
| 8 | M&L pressed steel frames for doors with one or more rebates including necessary fixing lug, hinge, lock strike plats etc complete size of frame 105mm X 60mm complete all as specified and directed. |
| 9 | M&L pressed steel frames for doors with one or more rebates including necessary fixing lug, hinge, lock strike plate etc complete size of frame 125mm X 60mm complete all as specified and directed. |
| 10 | M&L Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings. (Confirming to FE-410W(Gde-E250 Quality B) complete all as specified and directed. |
| 11 | M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 12 | M&L 40mm thick factory made designer door shutters, solid core construction with particle board core and covered with decorative face veneer with lipping on both sides and fitted to chowkats complete all as specified and directed. |
| 13 | M&L 2nd class hard wood 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed. |
| 14 | M&L factory made 35 mm thick flush shutters , solid core construction with block board core and plywood face panel commercial type on both faces complete all as specified and directed. |
| 15 | M&L 2nd class hard wood 30mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. Note: Glass panes & Wire mesh in panels shall be measured separately. |
| 16 | M&L Powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 17 | M&L Powder coated aluminium (minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing not less than 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, powder coated aluminium fittings such as handles - 02 Nos, 100mm long hinge - 03 Nos, sliding bolt - 01 Nos, tower bolt - 02 Nos in each door, powder coated aluminium snap beading and rubber gasket, screws etc complete all as specified and directed. Note: Glass shall be measured separately. |
| 18 | M&L Powder coated aluminium (minimum thickness of powder coating 50 micron) window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less than 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading and rubber gasket, screws, powder coated aluminium fittings such as peg stays 150mm long - 01 Nos, telescopic hinge 75mm long - 02 Nos, suitable handle - 01 Nos etc in each shutter complete all as specified and directed. Note: Glass and wire mesh shall be measured separately. |
| 19 | M&L powder coated aluminium sliding window shutters with frames (consisting of 02 Nos glazed shutters and 01 No gauge shutter) Series -D (25mm), 3 track sliding shutters, duly fitted with neoprene beading, glazing clips, locking device, aluminium alloy handles, heat absorbing glass 5.5 mm nominal thickness in glazed shutters, stainless steel wire mesh of 0.254mm nominal dia of wire and 0.95 mm average width of aperture in gauged shutter, Powder coated aluminium ornamental grill 8 mm dia, 75 X 75 mm aperture fixed in powder coated aluminium snap beading/ 'C' channel in outer surface of the window frame complete all as specified and directed. |
| 20 | Servicing and greasing of aluminium door including replacement of nuts, screws, rubber gaskets, pivot, taper clip etc including taking down carefully of door shutter of replacing unserviceable parts/components by new parts/components for smooth functioning of door and refixing the same in existing opening/position complete all as specified and directed. |
| 21 | S&F Solid PVC Double door frame of size 50mm x 95mm made out of 5mm Plain colour PVC sheet reinforced with M.S. tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed. |
| 22 | M&L Solid PVC door frame of size 50mm x 45mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed. |
| 23 | M&L Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded wood grain colour PVC `C' channel heaving a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wire gauzed (i.e. panel will be of stainless steel wire gauze in lieu of wood grain printed PVC sheet panel). The wire gauze shall be wrapped on an additional square 8mm M.S Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed. Note: Wire mesh in panels shall be measured separately. |
| 24 | M&L Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face ,supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. |
| 25 | M&L factory made plastiwood of 18 mm thick of any shape in cupboard/almirah fixed on wall with necessary cleats/angles on walls/plastiwoods including shutter complete all as specified and directed. |
| 26 | S&F for 100mm long Stainless steel butt hinge, medium weight, complete all as specified and directed. |
| 27 | M&L Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails suitable PVC sheet beading, and jointed together with solvent cement , supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed. |
| 28 | S&F 150mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed. |
| 29 | S & F 300mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing with complete all as specified and directed. |
| 30 | S&F aluminium anodised barrel tower bolt of extruded section 200mm long complete all as specified and directed. |
| 31 | S&F 75mm long Stainless steel butt hinge, medium weight complete all as specified and directed. |
| 32 | S&F 75 mm hasp & staple, safety type, aluminium anodised with steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 33 | S&F 100mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed. |
| 34 | S&F aluminium anodised barrel tower bolt of extruded section 100mm long complete all as specified and directed. |
| 35 | M&L in repair, stainless steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. |
| 36 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. |
| 37 | M&L in repair, 4 mm thick sheet glass, ordinary quality and glazing with oil putty/ wooden beadings complete all as specified and directed. |
| 38 | M&L in repair, 4mm thick Figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sq.m in each pane complete all as specified and directed. |
| 39 | M&L for post construction termite treatment in vertical and horizontal surfaces in joineries, cupboard etc complete including necessary drilling operation to insert anti termite chemicals and making it good complete all as specified and directed. |
| 40 | M&L Steel hold fast made of flat iron conforming to Fe-290 Gde E-165 of size 25 x 5mm bent to shape required with splitting end and drilling holes for fixing nuts & bolts (including nuts & bolts) including treating the steel surfaces with tar or coal tar black paint and sanding neatly newly tarred surfaces with clean sharp sand all complete all as specified and directed. |
| 41 | M&L for PCC type C1,1:3:6 (using 20 mm graded aggregate) for holdfast blocks complete all as specified and directed. |
| 42 | M & L for Preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer complete all as specified and directed. |
| 43 | Demolition of brick work built in Cement mortar or cement lime mortar incl all quoins, arches , pillar etc complete all as specified and directed. |
| 44 | M&L for Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 45 | M&L for Brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed. |
| 46 | Taking down cement plaster of any description on brick work or stone masonry walls including rackingout joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 47 | M&L 10mm thick rendering cement mortar (1:3) on ceiling , soffit of slab or concrete surfaces finished the surfaces even and fair without using extra cement complete all as specified and directed. |
| 48 | M&L 15mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and fair without using extra cement complete all as specified and directed. Please Enable Macros to View BoQ information |
| 49 | M&L 15mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and fair without using extra cement complete all as specified and directed. Please Enable Macros to View BoQ information |
