|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.-All kinds of soil |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.-All kinds of soil |
| 3 | SSupplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering --All work upto plinth level:1:4:8 ( 1 Cement: 4 fine sand : 8 graded well burnt brick aggregate 40 mm nominal size) |
| 5 | First class brick work in foundation and plinth including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 6 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.-All kinds of soil= Quantity same as item no 2 |
| 7 | Centering shuttering including struttings, propping etc. and removal of form work for: A)Lintels, beams, plinth beams, girders, bressumers and cantilevers with wooden plank |
| 8 | Suspended floors, roofs,landings, balconies and access platform with timber planks -Chajja |
| 9 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size)For Plinth Bend |
| 10 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto floor five level.Thermo-Mechanically Treated bars of grade Fe-500 D or moreQuantity |
| 11 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 12 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ).Including Extra for brick masonry work in triangular, square and rectangular pillars including cost of all materials as required complete. |
| 13 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ).P/wall for bath room |
| 14 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 15 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63mm thick with zinc coating not less than 275gm/m2 |
| 16 | Providing ridges or hips of width 60 cm over all width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers including a coat of approved steel primer and two coats of approved paint complete.0.63mm thick with zinc coating not less than 275gm/m2 |
| 17 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.-Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominalsize) |
| 18 | Providing and fixing factory made UPVC door frame made of UPVC extruded, section having an overall dimension, as below (tolerance +/- 1mm) with wall thickness 2.0mm+/- 02mm. corners of the door frame to be jointed with galvanized brackets and stainless screws, joint mitred and plastic wilded. The hinge side vertical of the frames reinforced by galvanized MS tube of size 19 × 19 mm and 1 mm +/- 0.1 mm wall thickness and 3 nos stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-In-Charge.Extruded section Profile size 48x40 mm. |
| 19 | Providing and fixing to existing door frames. 24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of M.S. galvanised /plastic brackets of size 75×220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserying galvanised MS tube of size 20×20 mm and 1 mm ± 0.1 mm wall thickness. The lock rail made up of \\"H\\" Section, a UPVC hollow section of size 100×24 mm and 2 mm ± 0.2 mm wall thickness fixed to the shutter styles by means of plastic /galvanized MS \\"U\\" cleats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm ± 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontaly 6 mm galvanised MS rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-In-Charge. (for W.C. and Bathroom door shutter). |
| 20 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size) |
| 21 | Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wireincluding centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits.-40 mm thick |
| 22 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : |
| 23 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete |
| 24 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.Fixed to openings /wooden frames with rawl plugs screws etc. |
| 25 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required |
| 26 | 15 mm cement plaster including neat cement punning on the rough side of single or half brick wall of mix:- cement mortar 1 : 4 ( 1 cement : 4 fine sand. |
| 27 | 12 mm cement plaster of mix including neat cement punning- cement mortar 1 : 4 ( 1 cement : 4 fine sand ) For plinth |
| 28 | 12 mm cement plaster of mix-cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 29 | 15 mm cement plaster on the rough side of single or half brick wall of mix:-cement mortar 1 : 4 ( 1 cement : 4 fine sand )Inside Room |
| 30 | 6 mm cement plaster of mix :In cement mortar 1 : 4 ( 1 cement : 4 fine sand )Toilet Room |
| 31 | Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position :-Local Teak Wood |
| 32 | Providing and fixing plain Multipurpose Cement board (High Pressure steam cured) as per IS : 14862 : 2000 with suitable screws for fibre cement board in ceiling etc. complete (frame work to be paid separately) :i) 6mm thick cement board |
| 33 | Providing and fixing plastic beading 38 mm in size with screws of approved quality for ceiling |
| 34 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering --All work upto plinth level:1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 35 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :-White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 36 | Providing and Fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :-One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 37 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :-White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 38 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required:-Kitchen sink without drain board |
| 39 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.-450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms |
| 40 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms. |
| 41 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 42 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:-Single socketed pipe75 mm OD |
| 43 | 110 mm OD |
| 44 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion 75 mm |
| 45 | 110 mm |
| 46 | Single equal tee with door |
| 47 | 110x110x110mm |
| 48 | Bend 87.5°i)75mm |
| 49 | 110mm |
| 50 | Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete.i)75mm |
| 51 | 100mm |
| 52 | Providing and laying cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded well burnt brick aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips etc. complete.40 mm thick with 20 mm well burnt brick aggregate. |
| 53 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 ( thickness to be specified by the manufacturer ) of approved make in all colours, shades of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1 : 3 ( 1 cement : 3 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. |
| 54 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622 - 2017, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick Cement Mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc.complete. |
| 55 | Providing and fixing G.I. pipes of medim class as per IS : 1239 with latest amendment complete with G.I. fittings and clamps, including cutting and making good the walls etc. complete as per CPWD specification and direction of the Engineer - in -charge.-Internal work - Exposed on wall20 mm dia. nominal bore |
| 56 | 25 mm dia. nominal bore |
| 57 | 40 mm dia. nominal bore |
| 58 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete as per CPWD specification and direction of the Engineer - in - charge.(New work)i)20 mm nominal bore |
| 59 | 25 mm nominal bore |
| 60 | 40 mm nominal bore |
| 61 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 62 | Providing & fitting fixing of tank nipple of approved quality as per direction of Engineer-in-charge.a) 25mm dia nominal bore |
| 63 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete :i)20 mm nominal bore |
| 64 | 25 mm nominal bore |
| 65 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):i) 40 mm nominal bore |
| 66 | Providing & installation of 1 HP motor 220 volt of single phase (make:- kirloskar, Crompton, CRI, Calema, or any approved ISI Brand) complete as per direction of Engineer-in-charge |
| 67 | Drilling and boring of 40 mm dia pilot hole by any suitable method and dismantling then after selection of acquitter as per direction of Engineer-in-charge |
| 68 | Providing and lowering UPVC strainer of approve quality with suitable steel cutter/threading/painting etc. complete as directed by Engineer-in-charge. |
| 69 | Providing and lowering 40 mm dia UPVC pipe in/call necessary fitting of approved quality for shallow tube well as per direction of Engineer-in-charge |
| 70 | Providing and installation of hand pump of approved quality with washing as per direction of Engineer-in-charge |
| 71 | Applying Priming Coat. -With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard or soft wood). |
| 72 | Painting with synthetic enamel paint of required colour of approved brand and manufacture to give an even shade. -Two or more coats on new work |
| 73 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade)-New work ( two or more coats) over and including water thinnable priming coat with cement primer |
| 74 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture -New work ( two or more coats applied @ 3.28 litre/10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete. |
| 75 | Hiring charge for vehicle Maruti Omni/Maruti Wagon R/ Maruti Eco etc. (Haltage and milege) will be recorded and signed by both the Engineer-in-charge and the agency. |
| 76 | Transportation charge for work supervision by Maruti Omni/Maruti Wagon R/ Maruti Eco (As needed time by the Engineer-in-charge the agency will arrange vehicle as mentioned above at his own cost and risk Please Enable Macros to View BoQ information |
