|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 mtr in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 mtr, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 mtr. |
| 2 | Excavating in post holes (or similar holes) each not exc 0.5 Cu.m, getting out in soft soil returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm all as specified and directed. |
| 3 | M&L for Hardcore of guage exc 63mm but not exc. 100mm, deposited, spread and levelled in layers not exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified. |
| 4 | M&L for PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in foundations filling in mass concrete all as specified. |
| 5 | M&L for PCC (1:3:6) type C2 using 40 mm graded stone aggregate as in foundations filling in mass concrete all as specified. |
| 6 | M&L for PCC 1:2:4 type B2 using 40 mm graded stone aggregate as in floor 150 mm thick complete all as specified |
| 7 | M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in floor 100 mm thick complete all as specified. |
| 8 | Returning, filling in and including spreading, levelling, watering and well ramming in layers not exc 25 cm all as specified. |
| 9 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified & directed. |
| 10 | M&L for approved good earth filling in floors or pavings, laid in layers not exc. 15 cm thick, spread, levelled and rammed including watering all as specified. |
| 11 | M&L for brick work with sub-class 'B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) all as specified |
| 12 | M&L for 40mm thick Damp Proof Course in Cement concrete (1:2:4) Type B0, using 12.5mm graded stone aggregate to horizontal or vertical surfaces including necessary formwork complete all as specified |
| 13 | S&F steel work in tubular tursses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st -240 complete all as specified. |
| 14 | S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 15 | S&F Structural steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment, Fe-410-W (Gde- E-250) quality-B, with riveted, bolted or welded atachment complete all as specified. |
| 16 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified. |
| 17 | M&L for False ceiling with 'E' board \\"Classic\\", reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on anodised aluminium snap grid to support the boards/files with aluminium anodised main 'T' section 36mm x 25mm x 1.40mm cross tee 23.50mm x 23.50mm x 1.40mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides including hanging arrangements complete all as specified and as directed |
| 18 | M&L for Rendering 15mm thick on fair faces of brick or concrete surfaces in CM (1:6) finished even and smooth without using extra cement all as directed by Engineer in Charge. |
| 19 | M&L for rendering 15mm thick on fair faces of brick or concrete wall surfaces in cement mortar 1:4 finished surfaces fair & even using WPC (Water Proofing Compound) as per manufacturers instructions complete all as specified and directed.Note : WPC measured and paid separately. |
| 20 | Supply only Integral waterproofing compound complete all as specified and directed. |
| 21 | M&L for preparation of newly plastered wall surfaces and applying two coats of Oil Bound Distemper over a coat of chalk whiting (preparatory to distemper) applied over 1 to 2 mm thick BIRLA/ JK (or equivalent) water-proof wall care putty complete all as specified and directed by Engineer -in-Charge. |
| 22 | Material & Labour for Preparing new plastered or unplastered surfaces and applying two coats of 100% Premium acrylic emulsion paint (camouflage paint) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed. |
| 23 | M&L for preparation for new steel untreated surfaces of any description, over 10 cm in with of girth, not otherwise described two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified. |
| 24 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild steel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated). (Note: The unit rate quoted by contractor includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 25 | Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor includes all other connected accessories. Net Opening will be measured for payment purpose.)(A) Area not exceeding 2.00 sqm each |
| 26 | S&F of Anodised aluminium grill (Min thickness 5.2mm and of 2.4Kg/Sqm weight) of approved design/ pattern, with approved standrad section and fixed to existing window frame with CP brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in Charge. |
| 27 | S&F for Aluminium Mortice lock, vertical type of size 75mm, 4 lever, complete all as specified and as directed by Engineer-in-Charge. |
| 28 | Supply & fixing 5.5 thick sheet glass, odinary quality exc 0.5 Sqm in each pane complete all as specified and directed. |
| 29 | M&L for RCC M25 grade (Design mix) (with 20 mm graded stone aggregate) as in foundation, footing & plinth beam etc complete all as specified and directed. |
| 30 | M&L for RCC M25 grade (Design mix) (with 20 mm graded stone aggregate) as in column complete all as specified and directed. |
| 31 | M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surface all as specified & directed by Engineer in Charge. |
| 32 | Rough finished Formwork to sides of pillars, posts, struts, columns and stanchions circular on plan |
| 33 | M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 for backing of Dado/ Skirting. |
| 34 | M&L for TMT steel bars 10mm dia and over cut to length bent to shape required, incl cranking bending spirally for hooping for columns, hooking ends and binding with MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as directed by Engineer in Charge. |
| 35 | All as per item no 34.00 here in above but 5mm dia & over upto and incl 10mm dia in stirrups, spacers and binders. |
| 36 | Supply and fix of Steel rolling shutters thickness of laths in 1.25 mm, gear operated type with chain wheel and hand chain and electric gear box with provn of suitable motor , as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated and as directed. |
| 37 | Supply and fix for Safety lever locks mild steel with 4 levers for rolling shutters . |
| 38 | M&L for 75mm thick PCC (1:3:6) type C2 using 40mm graded stone aggegate as in plinth protection, surface finished even and smooth complete all as secified & directed by Engineer in Charge. |
| 39 | S&F mild steel flat iron 40x3mm as in valley gutter and wind tie and similar work including securing botl and necessary drilling work conforming to Fe 290 Gde-165 |
| 40 | M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed. |
| 41 | S&F of Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 42 | S&F for Anodised aluminium Powder coated (thickness of powder coating not less than 50 micron) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. |
| 43 | S&F for 12mm thick Particle board for insulation purposes , fixed with screws to aluminium frame work complete all as specified and directed. |
| 44 | S&F in repair mild steel mortice lock 4 levers, vertical type, size 100mm complete, all as specified and directed. |
| 45 | S&F for Anodised aluminium Powder coated (thickness of powder coating not less than 50 micron) window and ventilator shutters, sliding type with sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinges type B-21 100 mm long (2 no.) suitable handle (1no.) complete all as specified |
| 46 | Material and labour for Point wiring with 1.5 Sqmm FR PVC insulated and sheathed multi stranded (FRLSH) copper conductor cable in and incl rigid PVC conduit concealed for one light or one fan controlled by one switch incl 1.5 Sqmm (FRLSH) PVC insulated and unsheathed multi stranded copper conductor cable as earth wire (green colour) to common earth dolly complete all as specified and directed by Engr-in-charge. Note: (a) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc(b) On RCC roof ceiling PVC conduit shall be provided on surfaces for fan etc with proper fixing clips all as directed |
| 47 | All as per serial item No 46.00 here in before but for one 3 pin 5 Amp socket outlet on independent board. |
| 48 | All as per serial item No 46.00 here in before but for one 3 pin 5 Amp socket outlet on same board. |
| 49 | Material and labour for Point wiring with 4.0 sqmm FR PVC insulated and sheathed multi stranded (FRLSH) copper conductor cable drawn in and including rigid PVC concealed conduit medium grade of suitable size with sunk cast iron/pressed steel terminal boxes of adequate size with suitable thickness plastic laminated sheet, cover for one 3 pin socket outlet 15 Amp on independent board including continuous 4.0 sqmm copper conductor cable (FRLSH) (multistranded) PVC insulated and unsheathed Cable as earth wire to common earth dolly, complete all as specified and directed by Engr-in-charge |
| 50 | Material and labour for ceiling rose surface bakelite two to three terminal isolated body fixed on PVC round block, 6A, Pilot 2 Plate, complete all as specified and directed by Engr-in-charge |
| 51 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. |
| 52 | Supply and fix in repairs of DB 8 way MCB SPN double door, glazed type, IP 43 protection,Glazed door, isolated neutral bar,insulated bus bar assembly,mechanical strength of IK09, complete all as specified and directed. |
| 53 | Supply & fix in repair of MCBs single pole (SPN) 6 to 32 Amps with 10 KA breaking capacity of 'C' series in distribution boards confirming to IS/IEC 60898-1 (ISI marked) complete all as specified and directed. |
| 54 | Supply & fix in repair of MCBs single pole (SP) 6 to 32 Amps with 10 KA breaking capacity of 'C' series in distribution boards confirming to IS/IEC 60898-1 (ISI marked) complete all as specified and directed. |
| 55 | M&L for Type 1+2 AC Surge Protection Device 1P+N (2 Pole) 320 volt, 15KA, without Remote Signaling, complete all as specified and directed. |
| 56 | M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of SSR Part-I (2009) including filling of charcoal dust , common salt all around Earth plate upto 150mm, 20mm bore GI medium grade watering pipe, 15 mm bore light grade earth lead protection pipe upto main board, funnel with wiremesh, 40mm thick RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate reinforced with suitable handle and angle iron frame and necessary excavation and earth work in any type of soil etc. complete all as specified and as directed including testing on completion. (Note: The rate quoted shall inclusive of GI wire 4 mm dia with GI pipe protection 15 mm, light grade up to 7.5 m) |
| 57 | S&F Metal flush Box 1/2 Module, complete all as specified and directed by Engr-in-charge |
| 58 | S&F Metal flush Box 3 Module, complete all as specified and directed by Engr-in-charge |
| 59 | S&F Metal flush Box 6 Module, complete all as specified and directed by Engr-in-charge |
| 60 | S&F Metal flush Box 12 Module, complete all as specified and directed by Engr-in-charge |
| 61 | S&F Modular Plate 2 module White cover plate with frame, complete all as specified and directed by Engr-in-charge |
| 62 | S&F Modular Plate 3 module White cover plate with frame, complete all as specified and directed by Engr-in-charge |
| 63 | S&F Modular Plate 6 module White cover plate with frame, complete all as specified and directed by Engr-in-charge |
| 64 | S&F Modular Plate 12 module White cover plate with frame, complete all as specified and directed by Engr-in-charge |
| 65 | M&L for Modular type 5 step Fan Regulator - 2 M oro white, complete all as specified and directed by Engr-in-charge |
| 66 | M&L for Modular switch 6 A One way switch white, complete all as specified and directed by Engr-in-charge |
| 67 | M&L for Modular 6 A, 5 pin socket, complete all as specified and directed by Engr-in-charge |
| 68 | M&L for Modular 6 A/16 A socket, complete all as specified and directed by Engr-in-charge |
| 69 | M&L for Modular 16 Amp One way switch white, complete all as specified and directed by Engr-in-charge |
| 70 | M&L for Dummy Plate - 1 Module Oro (White), complete all as specified and directed by Engr-in-charge |
| 71 | Supply and fixing ceiling fans complete with three blades, down rods, with modular electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed by Engr-in-Charge |
| 72 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450m sweep with, blades, and frame and louvers complete all as specified and directed by engineer in charge. |
| 73 | Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 Sq mm 4 core all as specified and directed. |
| 74 | Excavating in trenches not exc 1.5m wide and not exc 1.5m deep and getting out in soft / loose soil complete all as specified and directed |
| 75 | Removing excavated materials (soils) to a distance not exc 50.00 mtr and depositing where directed at a level not exc 1.50 mtr above the starting point , complete all as specified and as directed. |
| 76 | M&L for sand cushioning for protection of lT under ground cable with screen wash sand and punning to proper reqd cover all as specified and directed. |
| 77 | M & L for brick protection with old size sub class ‘B’ brick for PVC under ground cable protection in trench with width equal to length of brick laid dry and flat joining each other with gap between adjacent brick not exceeding 10mm over LT under ground cable all as specified and directed. |
| 78 | S&F Sheet metal enclosure having single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp. |
| 79 | S&F LED Highways light of capacity 100 W with toughened glass round in PDC housing, with minimum luminaire efficiency up to 125 lm/W, 10 KV SPD & ingress protection of IP66 with additional safety chain all as specified and directed. Please Enable Macros to View BoQ information |
