|
| 1 | EXCAVATION in foundation in ordinary Soil ( Loam, clay or sand ) including lift upto 1.5m and lead upto 30m and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal & disposal of surplus earth as directed by the Engineer-In-Charge upto a distance of 30 m.from foundation trenches by hydraulic excavator/manual means. For building/drain work only SI No 251 |
| 2 | Cement concrete with 4cm gauge stone ballast, course sand of 1.25 F.M & cement in propotion of 10:5:1 in foundation & under floors including supply of all materials , labour, tools & plants etc. Required for proper completion of the work |
| 3 | M-100 Brick work in 1:4 ( one cement& four coarse sand) mortar One Brick thick in Super Structure including supply of all materials, labour, Tools & plants etc. Required for proper completion of the work SI No 6.4.1 Page 30 SOR-2022 |
| 4 | M-100 Brick work in 1:4 ( one cement& four coarse sand) mortar Half Brick thick in Super Structure including supply of all materials, labour, Tools & plants etc. Required for proper completion of the work SI No 6.13.2 Page 30 SOR-2022 |
| 5 | Providing and laying in position specified grade of R.C.C. 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 stone aggrigrate ) including the cost of shuttering centering finishing and exculding reinenforcment all work .LINTEL |
| 6 | Providing and laying in position specified grade of R.C.C. 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 stone aggrigrate ) including the cost of shuttering centering finishing and exculding reinenforcment all work .BEAM & COLUMN |
| 7 | M.S. (tor steel or plain) in plain work such as R.C.C. Or R.B. Work including bending for proper shape & including supply of steel & its wastage, bend, hooks and authorised overlaping shall be measured and including cost of binding wire. |
| 8 | M.S Iron Work For Heavy Size and Section |
| 9 | 12 mm plaster 1:4 cement & coarse sand on brick work with cement mortar.SI No 13.4.1 Page 55 SOR-2022 |
| 10 | 15mm thick plaster with cement and course sand For Rough Face of 1.25 fineness modulus in 1:4 over brick work minimum thickness not be less than 1 cm including supply of all material ,labour tools and plants etc required for proper completion of work.SI No New(i) Page 55 SOR-2022 |
| 11 | Supply and Fixing of 35 mm thick flush door commercial quality including fixing of wooden cleats and stopper and including fixing and adjustment of hinges bolt lock handle spring fitting with necessary screw to be supplied departmentally SI No 9.21.1 Page 35 SOR-2022 |
| 12 | Providing and laying vitrified floor tiles in different sizes with water absorption less than 0.8% and confirming to IS: 15622, of approved make in all colours and shades laid on 20mm thick cement motar 1:4 (1 cement: 4 coarse sand ), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc, complete.Page 59 |
| 13 | Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 14 | Providing and fixing, in position concealed G.I. section for wall paneling using board of required thickness fixed on the ‘W’ profile (0.55 mm thick) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. Board is fixed to the ‘W’ profile with 25 mm countersunk ribbed head screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-in-charge, the joints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish . (Acoustic wall panneling) |
| 15 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mmfor Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for :(i) Sites with basic wind speed > 45 m/sec as per IS 875 – Part 3 (ii) Sites with structure height more than 20m for all wind speeds (Fixed window / ventilator with mullion / transom)Using R3 series with frame (55 mm & above )x (45 mm & above) & mullion (55 mm & above)x (65 mm & above). (Height upto 2.5 metre) |
| 16 | Supply and Fixing of 6 mm thick china white glazed tiles on wall or dado laid with 1:3 cement and approved coarse sand mortar finished with white cement jointed and polishing complete including supply of all material labour required for proper completion of work.SI Nos 628 SOR 2022 Page 60 |
| 17 | Providing and Applying white cement based putty of average thickness 2 mm of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete including cost of all material Labour T&P etc. Complete required for proper completion of the work.DSR No 13.26 SOR 2022 Page 61 |
| 18 | Wall painting ( Two Coat )with plastic emulsion of approved brand and manufacture on decorative wall surface to give an even shade including thoroughly brushing the surface clean of all dirt grease loose pieces and prapare smooth surface including cost of all material labour T&P etc. complete requird for proper completion of work. SI.No 17 +18New SOR 2022 Page 63 |
| 19 | Finishing wall (Two Coat ) with exterior paint (Apex) of approved brand and manufacture and of required shade on undercoated wall surface to give even shade including one coat of primer applied curing cost of all material labour T&P etc.SI.No (21 New) SOR 2022 Page 63 |
| 20 | Painting two coat or including preparing the surface by thoroughly clearing the surface of all dirt dust and scrapping and papering Including cost of all material labour T&P etc required for proper completion of work.SI.No (2New+4New) SOR 2022 Page 61 (33+125)=158 |
| 21 | Providing and Fixing of 15mm dia GI pipe complete.Page 83 |
| 22 | Providing and Fixing of 110mm dia PVC pipe complete.Page 87 |
| 23 | Providing And Fixing of 15 mm nominal bore C.P brass long body bib cock approved quality confirming to IS standard and weighing not less than 690 gm SOR 2022 Page No 86 |
| 24 | Providing and Fixing of water closet squitting pan European Type WC PAN with 100mm sand cast iron P or S Trap ,10 litre low level white P.V.C flushing cisten including flush pipe with manually controoled device with all fitting and fixture complete. SI No 2 PAGE 89 SOR 2022 |
| 25 | Providing and Fixing 600x450 mm beveled edge mirror Page 77 SOR 2022 page 91 |
| 26 | Providing And Fixing of 15 mm nominal bore C.P brass stop cock approved quality confirming to IS standard and weighing not less than 690 gm SOR 2022 Page No 86 |
| 27 | Supply And Fixing of LED Tube Light1x22 watt, 2200 system lumens 100lm/watt PF>0.95 THD<10%,CRI>80,Tube with aluminium heat with 3 year warrantee with polycarbonate tube light complete including tube suitable for both surface and suspended complete in all respect. SI No 1413 (ii) (ELECTRICAL WORKS SOR 2018) |
| 28 | Supply and Fixing Door closer SOR-2022 page 39 |
| 29 | Providing and Fixing window blinds of waterproof suitable material as required window size (including 1 x Roller Shade, 1 x Plastic Cord/Chain, 2 x Brackets (Can be fixed to the wall ), 4 x Screws and 4 x Fishers) with functionality convenience for any home or offices, provide excellent UV protection, complete room darkening and enhanced privacy all complete as per drawings, specification and direction of the Engineer in Charge. |
| 30 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). |
| 31 | Wiring point for light with 1.50 Sq mm FRLSH PVC insulated multistrand copper conductor cable in heavy gauge rigid steel conduit pipe concealed in the wall, complete Electrical SOR-2018 SI No 131 c |
| 32 | Wiring point for two ways light with 1.50 Sq mm FRLSH PVC insulated multistrand copper conductor cable in heavy gauge rigid steel conduit pipe concealed in the wall, complete Electrical SOR-2018 SI No 132 |
| 33 | Supply and wiring of submain with two number 16 sqmm PVC insulated 1100V gradeMultistrand single core copper conductor cable in 25mm dia heavy gauge Electrical SOR-2018 SI No 214(C) |
| 34 | Supply and Fixing of Switch box 200x250x65 mm size of approved smake made up of 1.0 mm thick ISI marked GP sheet all 4 corners folded and spot welded for screws Electrical SOR-2018 SI No 163 |
| 35 | Supply and Fixing of 63 Amp 415 V metal clad TPn rewireable type switch fuse unit on angle iron bracket complete in all respect.Electrical SOR-2018 SI No 316 |
| 36 | Supplying And Fixing of 16 Sqmm 4 core aluminium cable |
| 37 | Supply and Fixing of 16 Sqmm plain or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connection etc.Electrical SOR-2018 SI No 504(d) |
| 38 | Supplying And Fixing of 6Amp to 32 Amp SP MCB (10KA) C Curve Electrical SOR-2018 SI No 1002 |
| 39 | Supply and Fixing of Ceiling Fan Dust Fighter 1200mm Sweep (Sanctioned Rate) |
| 40 | Supply and Fixing of Exhaust Fan 250mm Sweep (Sanctioned Rate) Please Enable Macros to View BoQ information |
