|
| 1 | Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed. |
| 2 | M&L for brick work with modular fly ash bricks, straight or curved on plan exc 6m mean radius in CM 1:6 complete all as specified and directed. |
| 3 | Demolition of cement concrete (un-reinforced) any description and laid in any position complete all as specified and directed. |
| 4 | M & L for 75 mm thick cement concrete 1:3:6 type C-2, using 40 mm graded stone aggregate as in plinth protection laid to slop of 1:12, finished surface even and fair without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints through out the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed. |
| 5 | Demolition of cement concrete (reinforced) in ground floor and paving n.exc 15cm thick above or below ground level complete all as specified and directed. |
| 6 | Taking down cement or cement lime plaster including tiles if exists, from brick or stone walls / ceilings etc. including raking out joints, hacking for keys, scrubbing down with water etc. including removing of rubbish off the premises complete all as specified and directed. |
| 7 | M&L for rendering 15mm thick in CM 1:6 on brick work or concrete surface of wall and finished surface even and smooth without using extra cement all as specified and directed. |
| 8 | M&L for rendering 15mm thick in CM 1:4 on brick work or concrete surface of wall and finished surface even and smooth without using extra cement all as specified and directed. |
| 9 | Complete removal of existing treatment by scrapping with Wall Sander having mechanical vacuum mechanism having RPM not less than 1500, sanding pad of 80 Grit having dia of 7\\"/9\\" to make the surface free from dust loose paint etc complete all as specified and directed. NOTE: 1. The Item No 9, 10, 11 and 12 here-in-after shall by executed through authorised applicator of OEM under provision of a tri-party MoU (Contractor, authorsied applicator of OEM and manufacturer of materials)2. The above mentioned MoU shall be submitted to GE (through Engr-in-Charge) for Go-ahead before execution of work. 3. The work shall be executed up to height of approx 14 mtr, contractor shall arrange necessary scaffolding and saftey arrangements. 4. Please note that quoted unit rate shall be deemded inclusive and no extra cost shall be paid for above mentioned provisions. |
| 10 | M & L for waterproof cement based putty @ 1 Kg(undiluted) per sq mtr. of average thickness 1mm, over the plastered/old painted wall after scrapping to prepare the surface even and smooth complete and Sanding of the putty surface with wall sander having mechanical vacuum mechanism having RPM not less than 1500, sannding pad of 240 Grit or above having dia of 7\\"/9\\" to make the surface free from dust complete all as specified and directed. Step 1) Mix the putty powder by adding 40-50% water and mix it with mechanical Putty mixer having power min 1400 W and havinng mixer rod of industrial stell grade 45 with the mixing capacity of min 2.5 kg putty per minute).Step 2) Apply the first coat the prepared mixer with the help fully automatic airless spray putty application machine having a DC electric motor of 3.3 KW having flow speed of max 6 ltrs per minutes with a maximum pressure 230 bar having maximum tip size 0.041\\" Step (3) Allow 6-8 hrs time to dry the putty surface. NOTE: Ref Notes given under item No 9 above. |
| 11 | M & L for one coat of acrylic water based exterior grade primer @0.9 ltr(undiluted)/10 sq mtrs diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application having an electric motor of min 1 HP with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface for painting of subsequent quotes as per manufacturer instructions complete all as directed. NOTE: Ref Notes given under item No 9 above. |
| 12 | M & L for water based premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology ,Excellent Dirt Pick up Resistance with low VOC less than 50 G/L, Anti Algae properties in two coats @ 1.79 ltr (undiluted)/10 sqm diluted with water in 5:2 ratio applied over priming coat with fully automatic airless spray paint application machine having an electric motor of min. 1 HP with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI and allow 6-8 hrs to dry the surface before application of subsequent coats complete all as specified and directed. NOTE: Ref Notes given under item No 9 above. |
| 13 | M & L for preparation for surface of new plastered wall and distempering with 1st quality acrylic distemper (ready mixed) in two coats having VOC content less than 50 gms/litre of required shade and colour including over a coat of primer complete as per manufacturer's specification. |
| 14 | M & L for providing and applying white wall care putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed. |
| 15 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) and area exc 1.5 Sqm but n.exc 4 sqm each complete all as specified and directed. |
| 16 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) and area n.exc 1.5 Sqm each complete all as specified and directed. |
| 17 | S & F double rebated Factory made single extruded WPC (Wood Polymer Composite) solid door/ window / Ceosetory windows & other Frames/Chowkhat of size 65x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite / borer proof, water/ moisture proof and fire retardant complete all as specified and directed. |
| 18 | S & F double rebated Factory made single extruded WPC (Wood Polymer Composite) solid door/ window / Ceosetory windows & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite / borer proof, water/ moisture proof and fire retardant complete all as specified and directed. |
| 19 | S&F Factory made 30 mm thick 100% solid WPC (Wood Polymer Composite) solid both side prelem 0.14 micron Flush door shutter wit 10mm deep CNC moulding design of required size comprising of virgin PVC resin of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 20 | S&F 30mm thick factory made prelem 0.14 micron solid WPC (Wood plastic composit) moulded glzed door shuter with wire mesh in 08 number of division with brown wood grain texture including SS wire mesh (G-304) 0.36 mm minimum dia of wire and average width of aperature 1.4mm with XPM Aluminium alloy wire cloth of wire shall to be fixed with 15x15 square tube in side rails with screwing 8x28 heat metel zink coated screws can be remove of fix again after changing of wire mesh needed. The density not less then 780kg /Cum shall be as per manufacture instruction complete all as specified and as directed |
| 21 | Supply & fixing Factory made uPVC prelem colour three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 112 x 52mm & sash 42x 68 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi- chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. |
| 22 | S&F 12 mm thick toughened glass as in hinged doors, partitions, automatic doors and similar work including cutting to shape, drilling holes required and pivot at top fance type glass handle of size not less than 300 mm on both sides of shutter to match with colour of glass shutter top and bottom aluminium rail with suitable locking arrangement and all necessary fitting complete all as specified and directed. |
| 23 | M&L as for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, fixed in repairs, with & including replacement of floor tiles if any broken during repair work and making good disturbed surfaces matching to the existing surfaces complete all as directed. |
| 24 | S & F 18mm HDHMR boards and back of 10mm same boards laminated on both sides with 0.7mm thick mica on internal sides and 1 mm thick decorative mica on outer visible side complete all as specified and directed. |
| 25 | S & F Magnet Ball catches with 8mm dia steel ball, and brass body and striking plate for cup board / cabinet shutters complete all as specified and directed. |
| 26 | S & F 250 mm long stainles steel sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts all as specified |
| 27 | S & F for stainles steel barrel tower bolts 200 mm of extruded section and fixed. |
| 28 | S & F 125 mm size stainles steel handles fabricated type extruded section, ISI marked all as specified. |
| 29 | S & F auto concealed stainless steel hinges medium weight and fixed complete all as specified and directed. |
| 30 | S & F Butt hinges 125 mm stainless steel hinges medium weight and fixed complete all as specified and directed. |
| 31 | Dismantling of stone slabs and tiles of any description or thickness in floors, platform, aprons etc laid bedded and pointed in any mortar complete all as specified and directed. |
| 32 | M & L for 20 mm thick granite (of any type and colour ) work (table rubbed and polished ) in steps, Jambs, pillars, window cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust and admixture of pigment to match with shade of granite complete all as specified. |
| 33 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 34 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed. |
| 35 | M & L for vitrified ceramic tiles dark shade digital tiles/(double charged), 10mm thick (square/ rectanglar) polished, exceeding 0.42 sqm of each tiles not exceeding 1.00 sqm, in floors etc. laid over and including 15mm thick screed bed of cement mortar in 1:6, set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified |
| 36 | M & L for Non skid ceramic coloured tiles 7 to 8 mm thick(square/ rectanglar) area of each tiles exc 0.18 Sqm but not exc 0.38 Sqm in floor including screed bed 15mm thick or beding layer for laying floor finishes CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 37 | M & L for glazed ceramic tiles (coloured) in vertical surfaces 600x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to matchover 10mm thick rendering in cement mortar 1:3 complete all as specified and directed. |
| 38 | M&L for machine cut kota stone slab flooring 19-20mm thick over and including cement screed bed 15mm thick in CM 1:6, base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified. |
| 39 | M & L for exterior tiles(Heavy duty) of superior quility 400x400x10-12MM thick of approved size/design/shade set and jointed in neat cement slurry & pointed in white or coloured cement to match as in floor over and including 20mm thick screed bed in cm 1:4 complete all as specified and directed. |
| 40 | S & F in repairs Vitreous china wash down water closet pan (pedestal pattern) white (including fixing bolts, flush pipe, and excluding flushing cistern and seat cover ) and including connection to drain (or out going pipe) and flushing pipe etc complete all as specified and directed. |
| 41 | S & F in repairs plastic water closet seat cover coloured/white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device all as specified and directed. |
| 42 | S & F in repairs 10 Litres capacity PVC valveless syphonic action type flushing cistern low level, white with inlet ball valve float and handle including brackets connection to pipes and fixing of lever if any joint between flushing pipe and socket of WC complete all as specified and directed. |
| 43 | S & F in repairs Vitreous china (Counter type) WHB White (C, size 445x445x130 mm with including waste coupling and waste pipe of 32mm dia complete all as specified and directed. |
| 44 | S & F in repairs vitreous china urinal, Half stall type white (excluding flushing cistern but including flushpipe and waste pipe) compete including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60cm long brass screws pointing around urinal back in cement fixiing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe including connections to flushing pipe and outgoing pipes complete all as specified and directed. |
| 45 | S & F in repairs 110mm PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed. |
| 46 | S & F in repairs 110mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in trenches or wall complete all as specified and directed. |
| 47 | S & F in repairs 75mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in trenches or in floor/wall all as specified and directed by Engineer-in-charge. |
| 48 | S & F in repairs 110mm bore PVC (SWR) bends, any radius. |
| 49 | S & F in repairs PVC (SWR) bends any radius of 75 mm dia all as specified. |
| 50 | S & F in repairs PVC (SWR) 75/100 mm floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 51 | S & F in repairs 15mm dia fancy type chromium plated brass bib taps cast copper alloy with crutch or butterfly handle, scresed down screwed for iron pipe or for brass ferrule and fixed both ends for iron pipe or for unions complete all as specified and directed. |
| 52 | S & F in repairs 15 mm dia Pillar tap cast copper alloy chromium plated brass, fancy type with capstan head and cup screwed down screwed for G I pipe or for brass ferrule all as specified. |
| 53 | S & F in repairs of 15 mm bore fancy type, chromium plated stop valve, with long shank and cup (Concealed Type) cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 54 | S&F 15mm dia fancy type chromium plated brass angle valve/cast copper ally screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed to GI Pipe complete all as specified and directed. |
| 55 | S & F in repairs 15mm dia CP brass two way bib tap consisting angle valve to control water suitable for jet cleaner complete all as specified and directed. |
| 56 | S & F in repairs CP brass soap dish any type fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 57 | S & F in repairs CP brass towel rails 20 mm dia and 600 mm long fixed as in repair including chromium plated brass screw and wooden / cleats complete all as specified and directed. |
| 58 | S & F in repairs bevelled edge mirror of selected quality 5mm thick glass mounted on fixed to stainless steel fastener 50mm long spacer/wooden plugs with chromium platated brass screw and cup washers complete all as specified and directed. |
| 59 | S & F in repairs PVC connection of 15 mm bore 600 mm long with PVC coupling on both ends of superior quality all as specified.PTMT nuts fixed complete all as specified and directed. |
| 60 | S & F in repairs 32 mm dia Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm 45gms/40mm-60 gms) complete all as specified and directed. |
| 61 | S & F in repairs 32mm dia PVC waste pipe approx 900mm long for sink/WHB complete all as specified. |
| 62 | S & F in repair health faucet for EWC CP hand hold with flexible pipe 1.5m long complete set all as specified. |
| 63 | S & F in repair sink made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with dwarf wall, connecting union to pipe, overall minimum size 495mm x 420mm bowl size 410mm x 330mm x 160mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete all as specified and directed. |
| 64 | S&F stainless steel drapery curtain rods standard quality dia not less than 25mm with fancy type stainless steel latoo at both ends and Stainless Steel Bracket for middle support as required all as specified and direced as approved by GE. |
| 65 | M & L for prepration of surface of walls and rendering/plaster by using readymix mixture of thickness 15 mm with white cement based polymer modified self curing mortar including water proofing compound as per manufacturer's instructions complete all as specified and directed.Note : Cost of WPC shall be deemed inclusive in quoted unit rate. |
| 66 | M & L for preparation of newly plastered surfaces of wall and applying 2-3mm wall care putty Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade (Two coats applied @ 1.79 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) paint etc by mechanical means complete all as specified and directed. |
| 67 | S & F in repairs 150mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints fixed to wall incl clamp at equal intervals all as specified and directed. |
| 68 | S & F in repairs 150mm bore PVC (SWR) bends, any radius. |
| 69 | S & F of 1000 Litre capacity triple layared rotational moulded polythene water storage tanks (cylindrical vertical with closed top) of specifications as per MES Schedule 2009, Part – I and hoisted, fixed in position incl dismantiling of old unservicable water tank of any capacity complete all as specified and directed. |
| 70 | S & F in repairs 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density Plastic ball Screwed for iron pipe and fixed (Minimum weight -210 gms. |
| 71 | S & F in repair Gun-metal, globe or gate valves 20mm with iron wheel head, screwed both ends for iron pipe all as specified |
| 72 | S & F of 15 mm bore steel water tubing medium grade galvanised with and including all fittings and fixed to walls and ceilings or laid under floors including taking up or down 15mm bore steel water tubing and connection complete all as specified and directed. |
| 73 | S & F of 20 mm bore steel water tubing medium grade galvanised with and including all fittings and fixed to walls and ceilings or laid under floors including taking up or down 20mm bore steel water tubing and connection complete all as specified and directed. |
| 74 | Removing existing roof treatment and preparing surfaces to the entire satisfaction of Engr-in Charge /GE including taking down existing plaster,cleaning of all foreign material such as grass roots dust etc and roughening the concrete surfaces by wire brushes and washing down to remove dust etc . flushing at junction of parapets complete and removing the same to the places complete all as specified and directed. |
| 75 | M & L for providing plain cement concrete, type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges with and including necessary form work as required complete all as specified and directed. |
| 76 | M & L for prepration of concrete surface such as roof and similar and rendering/plaster by using readymix mixture of thickness 15 mm with white cement based polymer modified self curing mortar including water proofing compound as per manufacturer's instructions complete all as specified and directed.Note : Cost of WPC shall be deemed inclusive in quoted unit rate. . |
| 77 | M & L for application of high perfomance hybride polyurea elastomeric water proofing coating cold applied, liquid membrane at 1.5 kg/Sqm with an elongation minimum of 500+100% by airless spray machine and tensile strength of minimum 11-13 N/mm2 as per ASTM D2370, crack bridging ability minimum of 3 to 4 mm as per ASTM C1305, Shore Hardness of minimum 70+5 as per ASTM D2240 including final preparation / cleaning of the plastered surface etc and applying epoxy primer of approved make in two coats at a coverage of 0.40 kg/Sqm, all as per manufacturer specification and as directed. NOTE: 1. The water proofing work shall by executed through authorised applicator of OEM under provision of a tri-party MoU (Contractor, authorsied applicator of OEM and manufacturer of materials)2. The above mentioned MoU shall be submitted to GE (through Engr-in-Charge) for Go-ahead before execution of work. 3. The work of roof treatment shall be executed at height of approx14 mtr and roof is inaccessible type, No any type of stair cases are available for transportation of building materials to roof. 4. Please note that quoted unit rate shall be deemded inclusive and no extra cost shall be paid for above mentioned provisions. |
| 78 | M & L for point with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm and earth continuity conductor with 1.5 sqmm colour code drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken modular GI metal boxes 1mm thick and modular cover plate with frame of approved colour for mounting modular switches, sockets etc including taking down carefully surface aluminium or copper point wiring (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, regulators, sockets etc and making good disturbed surfaces even and smooth using CM 1:3 including white/colour wash to match the existing surface complete all as specified and directed. |
| 79 | All as per Item No 78 as above but for One 5 A socket outlet on independent Board |
| 80 | All as per Item No 78 as above but for One 5 A socket outlet on same Board |
| 81 | M & L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 sqmm and earth continuity conductor with 2.5 sqmm colour code drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken modular GI metal boxes 1mm thick and modular cover plate with frame of approved colour for mounting modular switches, sockets etc as required including taking down carefully surface aluminium or copper point wiring (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, regulators, sockets etc and making good disturbed surfaces even and smooth using CM 1:3 including white/colour wash to match the existing surface complete all as specified and directed. |
| 82 | Supply and fix Rigid non-metallic PVC conduit of 25mm dia exclusive of boxes (junction/terminal) but inclusive of all tees, bends,elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc for protection of cables all as specifid |
| 83 | Supply and fix Modular switch one way 6A 230V AC 50 HZ SP one module all as specified. |
| 84 | Supply and fix Modular switch one way 16A 230V AC 50 HZ SP one module all as specified. |
| 85 | Supply and fix Modular socket 2/3 pin combined 6A 230V AC 50 HZ SP two module all as specified. |
| 86 | Supply and fix Modular socket 6A/16A 2/3 pin combined 230V AC 50 HZ SP two module all as specified. |
| 87 | Supply and fix MCB SP 230V, 6-32 Amps capacity all as specified and directed. |
| 88 | Supply and fix MCB SPN 230V, 6-32 Amps capacity all as specified and directed. |
| 89 | Supply and fix Modular Regulator 230V AC 50 HZ SP two module all as specified. |
| 90 | Supply and fix in repair of MCB DB SPN 8 way 230 volts, double door type with minimum capacity of 200 Amps rated bus bar including necessary dummy plate and necessary civil works all as specified and directed. |
| 91 | S&F Ceiling rose PVC polycarbonate all as specified. |
| 92 | Supply and fixing of wall/surface mounted integrated batten LED light luminaire of 4ft length with a system wattage of 20-22W with a nominal system lumen output of 2000-2200 lumens and a minimum system efficacy of 100Lm/W. CCT shall be 6500K and CRI ≥ 80. Housing shall be extruded aluminimum with powder coating & with IP20 protection, The luminaire shall meet IP20 rating with surge protection of 2.5KVA, THD ≤10% and PF ≥ 0.95, complete all as specified and directed. |
| 93 | Supply and fixing recess mounting LED light fitting 2'x2' luminaire architectural recessed luminaire with CRCA housing and Molded PC diffuser with an unique angular optics for making the illumination easy on eyes for light comfort in office areas with UGR<=19. The luminaire should have a color consistency SDCM< 5, CRI > 80 and choice of CCT: 5700K. Luminaire shall be designed to emit at least 3000 lumens and an efficacy of atleast 120Lm/W and maximum system wattage of 36 Watt, designed for ambient temp 45 deg C. The metallic electronic driver shall have a power factor >0.95, THD <10%, 4KV internal surge protection and the Ripple factor should be <5% to minimise the Flicker and Stroboscopic effect Fixture should have an operating voltage range of 140-270VAC complete all as specified and directed. |
| 94 | M & L for submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable using colour coding drawing into and including concealed rigid non metallic PVC conduit 20 mm dia, medium grade, ISI marked ivory colour along with accessories of nominal sizes 2x4 sqmm + 1x4 sqmm earth wire including taking down of old unservicable sub main wiring complete all as specified and directed. Note : (i) Cost of cutting & chasing for concealltion of conduit and making good as existing to distrubed surface shall be deemed inclusive in quoted unit rate. (ii) Three runs of 4 sqmm copper conductor and 01 run of PVC conduit shall be measured as one unit. |
| 95 | Supply and fixing ceiling fans remote operated complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) with copper winding incl remote complete all as specified and directed. |
| 96 | S&F in repairs LED security light fixture 35/36 watt powder coated pressure die cast aluminum body with driver Input voltage: 140-270 Volt AC, 50 Hz, operating temp range -15 deg to 50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency > 85%,THD < 10% as per IEC 61000-3-2 , P. F.≥0.95, IP- 66,IK-10, CRI >80, System lumen efficacy ≥105 <120 lm/Watt output, under voltage and over voltage protection, EMIEMC as per CISPR -15, lenses for beam angle as per IESNA type I/II/III as per the requirement, life time (LED & electrical circuitry) of minimum 50000 burning hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and fixture shall be of relevant BIS standard complete in all respect including connections with suitable size FRLS, PVC insulated copper conductor cable complete all as specified and directed.Note:- Heat sink of aluminum housing should be such that LED junction temperature shall not rise above 90°C. |
| 97 | Material and labour for earthing complete with galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipe medium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete all as specified and directed. |
| 98 | Cutting chases in concrete wall/stone for laying PVC conduit and making good to facings where required and pointing in cement mortar 1:3, and making good, cutting not exc 20 cm girth and matching wall color. |
| 99 | M&L for Chemical earthing complete for earthing test point with copper earth plate electrode in ground (Earth pit not less than 2.25 metre below normal ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, connected and including copper strip 25mm x 4mm (upto the body of euipment ) by means of copper bolts, nuts, check nuts and washers, earth plate surrounded by picked layers of earthing chemical 15 cm thick, all ground top and bottom and watering pipe 20mm bore of GI pipe medium grade with funnel, testing on completeion including PCC chamber (1:3:6) using 20mm grade stone aggregate and 50mm thick cover with RCC 1:2:4 type B-1 using 20mm grade stone aggregate and 8mm dia deformed TMT bars @ 10 cm C/C both way including form work and MS frame using MS angle of size 45mm x 4 mm x 5mm complete all as shown in electrical plate No. 3 of MES schedule 1991 Part-I |
| 100 | M&L for Chemical earthing complete for earthing test point with copper earth plate electrode in ground (Earth pit not less than 2.25 metre below normal ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, connected and including copper strip 32mm x 6mm (upto the body of euipment ) by means of copper bolts, nuts, check nuts and washers, earth plate surrounded by picked layers of earthing chemical 15 cm thick, all ground top and bottom and watering pipe 20mm bore of GI pipe medium grade with funnel, testing on completeion including PCC chamber (1:3:6) using 20mm grade stone aggregate and 50mm thick cover with RCC 1:2:4 type B-1 using 20mm grade stone aggregate and 8mm dia deformed TMT bars @ 10 cm C/C both way including form work and MS frame using MS angle of size 45mm x 4 mm x 5mm complete all as shown in electrical plate No. 3 of MES schedule 1991 Part-I |
| 101 | M & L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required copper strip20x3mm complete all as specified and directed. |
| 102 | Supply and fix copper strip of size 20 x 3.15 mm with saddles and fixing screws etc for roof conductors and down conductors above ground level complete all as specified and directed. |
| 103 | Supply and fix Galvanized iron strip of size 32 x 6 mm with saddles and fixing screws etc for roof conductors and down conductors above ground level complete all as specified and directed. |
| 104 | M & L for test point terminal block made of gun metal or phosphorus bronze size 75X75X25 mm drilled and screwed including 03 Nos 8 mm dia 25 mm long hex. Head screw complete all as specified and directed. |
| 105 | Taking down existing split type air conditioner Of any capacity from wall/roof and refixing the same after servicing of AC Complete all as specified and directed. |
| 106 | Taking down existing LT Cable of any size from wall/roof and refixing the same with suitable size of clamp, nut, bol, Gutties etc complete all as specified and directed. |
| 107 | Taking down bldg security light of any capacity and refixing the same complete all as specified and directed. Please Enable Macros to View BoQ information |
