|
| 1 | Supplying and installation of automatic premium quality Boom Barrier, Boom length - 6 meter Model ASN601 - 1. Opening and closing time - ( 6 Sec )2. Electromachnical Boom Barrier3. Very Smooth Movement. 4. Double limit : Electronic limit and motor sensor memory limit for boom rising and falling. 5. Interface: Infrared photocell interface, Loop detector interface and IC system interface.6. Operated by : Radio Receiver with Remote Controller, Push button and Dual Channel Loop Detector including with the name of MLA with their constituency is to be written on SS plate/retro reflective sheet of suitable size on Boom Barrier or as directed by Hon'ble area MLA |
| 2 | Supply & Laying 2x4 sqmm XLP insulated & PVC Sheated Copper Conductor Armoured Power Cable of 1.1 KV Grade on Surface(per mtr). |
| 3 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil |
| 4 | Excavating holes more than 0.10 cum & upto 0.5 cum including gettingout the excavated soil, then returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m. All kinds of soil. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size) |
| 6 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes |
| 7 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 8 | Providing and fixing 3mm thick white acrylic plastic sheet with nut & bolts as per direction of Engineer in-charge. |
| 9 | Providing and fixing IRC fabric mesh 75x25mm having weight not less than 7.75 kg per/sqm welded in frame of made of MS Angle iron and welded to fencing frame for boundary wall railing including welding minimum 100mm per sqm of mesh inlcuding making necessary requirement and priming coat with approved primer all complete steel as per direction of Engineer in charge. |
| 10 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 11 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 12 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size). |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns |
| 14 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 15 | 12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand) with floating coat of neat cement punning. |
| 16 | Supply and fixing of 2 Seater See saw HPS-SAL-706: Arihant / Koochie / Hugo / Kompon. The See Saw consists of 2 poles of Dia 114mm and thickness of 2.5mm which balances the horizontal rod at the center which is of size 1614 mm length and Dia 114 mm. It consists of 2 seats which is made of LLDPE virgin plastic of size 363 mm X 250 mm X 155 mm.Each seat consists of a safety stand in the horizontal balance bar which is of 500 mm X 462 mm and a thickness of Dia 32 mm.Specialized connectors such as clamps and couplings are to be cast from aluminum which is pretreated, and cured, with a baked on powder coat finish.Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. ALL WELDING IS CARRIED OUT BY ROBOTS [SIMMILIAR TO THE ONES USED IN THE AUTOMOBILE INDUSTRY], WHICH GUARANTEES STRONG AND SMOOTH WELDS ELIMINATING ANY RAG, WELD SCARS AND ENSURES THE INTEGRITY AND STRENGTH OF THE WELDED AREAS. Size:( L x W x H 1.91 m x 0.5 m x 0.82 m All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines. |
| 17 | Providing and fixing 36mm thick EPDM (Ethylene Propylene Deine Monomer) Rubber flooring on existing surface in required color and shape. The EPDM Rubber flooring should be laid at site in dual color and pattern as per the direction of the Engineer-in-charge. All complete as per manufacturer specification. |
| 18 | Providing Retro-reflective regulatory sign board of size 1200x900 mm made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders, photos etc. will be as per IRC - 67 with required colour scheme on the boards and with the high intensity grade A. The aluminium sheet to be riveted to S.S. frame of size 20x20x1.6 mm Square tube. The boards will be fixed to 2 No. 50mm dia post 3 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge. Please Enable Macros to View BoQ information |
