|
| 1 | Providing and laying cement concrete 1:2:4 (1 cement : 2 sand :4 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work including carriage of materials within all leads and lifts.: In Foundation and plinth |
| 2 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations cement mortar 1:4 (1 cement : 4 coarse sand) |
| 3 | 15 mm cement plaster on the rough side of single or half brick wall of mix including carriage of materials in all leads and lifts.(i) 1:4 (1 cement: 4 fine sand) |
| 4 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(i) Hot finished welded type tubes |
| 5 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In beams joists, chanels, angles, tees, flats with connection plates or angle cleats as in main and cross beams, hip and jack rafter, purlins connected to common rafters and the like including carriage of materials in all leads and lifts. |
| 6 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 7 | Providing and fixing 0.37mm thick prepainted TATA steel sheet liner in partition with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with self drilling screw 55mm size with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge. |
| 8 | Providing and fixing polycarbonated tranparent sheet 2.0 mm thick in roofing with galvanised J or L hooks bolts and nuts with G.I. Limpet and bitumen rubber washer complete with all accessories as required as per direction of Engineer-in-Charge. |
| 9 | Providing and fixing M.S. BP Sheet 2.00 mm thick in eaves board/ facia/ soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in charge (Base members of steel work shall be measured and paid separtely) including carriage of materials within all leads and lifts. |
| 10 | Providing and fixing M.S welded mesh 25mmx25mmx3mm thick as per approved design welding with electric plant complete including applying priming coat of red lead paint as per HP.PWD. Specification 1990 Volume-1 including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. |
| 11 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.(i) Size of Tile 600x600 mm |
| 12 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.(i) Size of Tile 450x300 mm |
| 13 | Painting with synthetic enamel paint on previously painted wood or steel surface of approved brand and manufacture of required colour to give an even shade one or more coats on old work including carriage of materials in all leads and lifts. Please Enable Macros to View BoQ information |
