|
| 1 | Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 2 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diax40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @ 230 mm interval ,including fixing of gypsum board/calcium silicate board to ceiling section and perimetre channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers’ specification and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimetre channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part-I : 2011 (Board with BIS certification marks) 12.5 mm thick tapered edge gypsum moisture resistant board |
| 3 | Supplying chemical emulsion in sealed containers including delivery as specified. Chlorophriphos / Lindane emulsifiable concentrate of 20% |
| 4 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL antitermite treatmentTreatment of soil under existing floors using chemical emulsion (Chlorophriphos/Lindane E.C. 20% with 1% concentration) @ one litre per hole, 300mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floor: |
| 5 | Repair of Tiles by way of removing broken tile pieces and replacing it with new one along with mortar below, grinding and polishing complete job. Repair area less than 1.8 sqm. |
| 6 | Repair of Bed along with necessary ply changing/ legs replacement alon with necessary fixing with fevicol and nails etc complete job. |
| 7 | Repair of Side Table along with changing of drawer channels with necessary fixing with polishing, fevicol and nails etc complete job. |
| 8 | Labour engaged for cleaning of roofs & courtyard area of staff qtrs. By collecting leaves and other waste material and disposal of same within 50 mtrs. lead |
| 9 | Engaging carpenter for day to day repairs to woodwork like doors, windows etc |
| 10 | Engaging welder for day to day repairs like doors, windows etc |
| 11 | Engaging plumber for day to day sanitary repairs etc |
| 12 | Removing dry or oil bound distemper, waterproofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 13 | Repairs to plaster of thickness of 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of walls complete including disposal of rubbish to the dupming ground within 50 meters lead with cement mortar 1:4 (1 cement : 4 fine sand). |
| 14 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 15 | 1 mm thick |
| 16 | 2 mm thick |
| 17 | Providing and applying Plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete |
| 18 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface complete job |
| 19 | Painting with premium acrylic emulsion paint of interior grade having VOC content less than 150grams/litre of approved brand and manufacture, icluding applying additional coats wherever required. in patches two or more coats in approved colour and shade. |
| 20 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, one or more coats on old work. |
| 21 | Finishing wall with acrylic smooth exterior paint of repaired shade old work (two or more coats)applied @1.67 litre /10sqm on existing surface . |
| 22 | P/F overhead counter cabinets madeout of 19mm thick commercial board, 6mm thick ply on backside and all inside/outside surfaces fitted with sunmica and piano hinges of standard quality incld. Handles, tower bolts complete job. |
| 23 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately) First class kail wood. |
| 24 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws |
| 25 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead : Of area of 3 sqm. and below |
| 26 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class Kail wood. 35 mm thick shutter |
| 27 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : Second class Kail wood 35 mm thick shutter |
| 28 | Providing & fixing cupboard made out of 19mm thick commercial board & 6mm ply on back ISI marked of standard quality as approved) all inside surface finished in laminate 0.8 mm thick of approved shade & quality, slidding shutters running sliding fittings (hettich or equivalent) made up of 19mm thick board lipped with laminate on inside, outside and backside on almirah and complete in all respects including all hardware fittings as approved hettich or equivalent) |
| 29 | Providing and fixing of sanitary fittings , fixtures complete job. |
| 30 | Polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank terrace (at all floor levels) |
| 31 | European WC (Jaquar) singl piece with soft close seat and cover complete job. |
| 32 | Internal work-Exposed on wall |
| 33 | 15mm nominal bore(medium) jindal/ prakash/surya or equivalent |
| 34 | 20mm dia. Nominal bore medium ( Jindal/ prakash/surya or equivalent) |
| 35 | 25mm dia. Nominal bore medium ( Jindal/ prakash/surya or equivalent) |
| 36 | Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall: |
| 37 | 15mm nominal bore ( medium) Jindal, prakash |
| 38 | 20mm dia. Nominal bore medium ( Jindal/ prakash/surya or equivalent) |
| 39 | Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) |
| 40 | 15mm nominal bore(medium) jindal/ prakash/surya or equivalent |
| 41 | 20mm dia. Nominal bore medium ( Jindal/ prakash/surya or equivalent) |
| 42 | 25mm dia. Nominal bore medium ( Jindal/ prakash/surya or equivalent) |
| 43 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. Internal work exposed on wall |
| 44 | CPVC 1/2\\" |
| 45 | CPVC 3/4\\" |
| 46 | CPVC 1\\" |
| 47 | Providing and fixing PVC pipe embedded in 1: 5: 10 inclu. trenching and refilling and making good the floor and wall complete. |
| 48 | 110mm nominal bore (medium) supreme , prakash or equivalent |
| 49 | Providing and fixing PVC pipes including all fittings .supreme , prakash or equivalent(external work) |
| 50 | 110mm nominal bore (medium) |
| 51 | 75mm dia nominal bore(medium) |
| 52 | Long body bibcock (Jaguar or equivalent) |
| 53 | Angle valve |
| 54 | Waste pipe |
| 55 | Wall mixer (Jaguar ) |
| 56 | Wash basin mixer (Jaguar ) |
| 57 | Gate valve 1/2 '' |
| 58 | Gate valve 3/4'' |
| 59 | Gate valve 1'' |
| 60 | PVC connection 18 '' |
| 61 | PVC connection 24 '' |
| 62 | Shower ( Jaquar) |
| 63 | Shower rod ( Jaquar) |
| 64 | Pillar cock (Jaquar) |
| 65 | Health faucet (Jaquar) |
| 66 | Paper Holder |
| 67 | Cistern Syphon (Jaquar or equivalent) |
| 68 | Towel Ring |
| 69 | Soap dish |
| 70 | Washbasin Jaqaur |
| 71 | Bottle Trap ( Jaquar) |
| 72 | Providing and fixing hardware fittings |
| 73 | SS handle 6\\" |
| 74 | SS hinges |
| 75 | Godrej Door lock |
| 76 | Door Stopper (SS) |
| 77 | Door closer (Hardwyn, Godrej) |
| 78 | Almirah lock (Godrej) |
| 79 | SS hinges al bihari ( Hettich) |
| 80 | Channels ( Hettich) |
| 81 | SS hanger rods with brackets 3' (1\\") dia |
| 82 | Sliding reducer/Channel (hettich) |
| 83 | Cylindrical lock |
| 84 | Slding drawer channels |
| 85 | SS Hinges for glass door of Ozone Make |
| 86 | P/F 19 mm thick board in shelves, shutters with veneer and polishing complete job. |
| 87 | P/F 6mm thick plyboard incld. Nuts, fevicol etc. |
| 88 | Removal of waste by mechanical means and disposal of the same beyond municipal limits |
| 89 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time |
| 90 | Repair and adjustment of shower door by disengaging the glass door and refixing it by asdhjustment of hinges along with greesing complete. |
| 91 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.1 Hot finished welded type tubes |
| 92 | Providing & fixing wall panelling consisting of water proof 12 mm thick HDHMR (HIGH DENSITY HIGH MOISTURE RESISTANCE) board fixed on walls with the support of formwork made up of alumunium tube (25mm x 50mm) fixed on existing walls using screws complete with cutting for switch boards and other requirements as per design. |
| 93 | Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite Work |
| 94 | Providing and fixing 10 mm thick toughened glass of any size for table top, glazings for windows. |
| 95 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
| 96 | Repair of Chairs and sofas alongwith change of Upholstry Please Enable Macros to View BoQ information |
