Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each complete all as specified and directed. |
| 2 | Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 Sqm and not exc 4 Sqm each complete all as specified and directed. |
| 3 | M & L for Resecuring or easing and adjusting door shutters of any size and any description without taking down shutter from frame complete all as specified and directed. |
| 4 | Dismantling boarding of any discription fixed in any position with screws complete all as specified and directed. |
| 5 | Demolition of stone, brick masonry built in cement mortar incl quoins, arches, etc but exceeding ashlar facing dressed stone Work etc. complete all as specified and directed. |
| 6 | M&L for Brick work with Fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in half brick wall bulit in cement mortar 1:6 complete all as specified and directed. |
| 7 | M&L for Fromwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 8 | M&L for Reinforced cement concrete type M 25 (design mix) (20mm graded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves as complete all as specified and directed. |
| 9 | S&F Ball catches with 8mm dia steel ball and brass body and striking plates including letting in fixed complete all as specified and directed. |
| 10 | S&F Solid single PVC door frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of Plain colour PVC sheet reinforced with M.S. tube, edges will be painted to match with prelam sheet suppling & fixing in opening as per specification & drawing including all fixtures shown on drawing complete all as specified and directed. |
| 11 | S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. M S frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelam PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail; stile &rails having one side feathered edge and on other side 10mm 90^0 bent edge, Paneling of 2mm thick prelam PVC sheet on bothfaces i.e front face & back face with particle board core to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, and including all hardware necessary for a door supplying & fixing in the frame at site as per specification & drawing. given SSR 2010 complete all as specified and directed. |
| 12 | S&F pressed steel door frames of size 125 x 60mm, made of 1.25mm thick sheet, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified directed. |
| 13 | S&F pressed steel door frames of size 105 x 60mm, made of 1.25mm thick sheet, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified directed. |
| 14 | S&F Factory made, 35mm thick 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, 35mm thick complete all as specified and directed. |
| 15 | S&F Factory made, 2nd class hard wood, 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass/ gauge etc. (without sash bars) edges or framing plain, chamfered or rounded fitted with cut or mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I section 8.20 (a), complete all as specified and directed. |
| 16 | M&L for PCC 1:3:6 Type C1(20mm graded aggregate) as in bed block for holdfast and filling door frame complete all as specified and directed |
| 17 | S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed |
| 18 | S&F 100mm size of Butt hinges, medium weight cold rolled mild steel complete door etc complete all as specified and directed. |
| 19 | S&F aluminium anodised barrel tower bolts of extruded section with 200mm long bolt, complete all as specified and directed. |
| 20 | S&F aluminium anodised barrel tower bolts of extruded section with 150mm long bolt, complete all as specified and directed. |
| 21 | S&F Extruded aluminium alloy handles fabricated type anodised 150mm size complete all as specified and directed |
| 22 | S&F Extruded aluminium alloy handles fabricated type anodised 100mm size complete all as specified and directed. |
| 23 | M&L for floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, 140mm long, fixed in floor complete all as specified and directed. |
| 24 | M&L for preparation of new steel or iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, comlete, complete all as specified and directed. |
| 25 | M&L for preparation of new wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of filler coat with grey filler or liquid wood filler, transparent, and bringing forward surfaces to smooth even finish, complete all as specified and directed. |
| 26 | M&L for stainless steel wire cloth, 0.71mm nominal dia of wire and average width of aperture 1.20mm and fixed with tinned tacks, or stainless steel wire staples complete all as specified and directed. |
| 27 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45mm & sash 46 x 62mm both having wall thickness of 2.3 ± 0.2mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note : For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 28 | Supply and fixing factory made uPVC white colour Two track two panels sliding glazed window upto 1.50m height made of (small series) frame 52 x 44mm & sash 32 x 60mm both having wall thickness of 1.9 ± 0.2mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) comprising of uPVC multi-chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately)Note : For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 29 | Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50mm mullion 47 x 68mm both having wall thickness of 1.9 ± 0.2mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8mm size for fixing frame to finished wall, plastic packers,plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately).Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 30 | M&L for Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290. Gde-E-165 complete all as specified and directed. |
| 31 | S&F Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (where even required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 32 | S&F 10mm thick toughened glass on stainless steel railing with stainless steel clamps with rubber gasket to vertical post or sliding panel incl rubber lines clamps etc and apply silicon sealent complete all as specified and directed. |
| 33 | S& F 18mm thick factory made PVC sheet one side pre laminated sheet kitchen cabinet shutter/ cupboard shutter. The 18mm thick sheet shutter bent at 90 degree and finish all edges at level for making edge lipping bending for 0.5mm thick PVC sheet lipping at all four edges using bodning etc complete all as specified and directed. |
| 34 | S&F factory made PVC shelf/ partition of required size consisting of panel of 12mm thick celuka PVC ply and for supporting the hold of shelf/ partition and shall provide 3 edges in size 18mm x 18mm as per required length the front side of the edge visible in the fronth of the self/ partition to be edge lipped by 18mm width x 1mm thick PVC sheet of density 600kg/cum manufactured by ISO 9001-2015 Certified company using solvent cement etc complete all as specified and directed. |
| 35 | S&F factory made PVC shelf/ partition of required size consisting of panel of 18mm thick required size consisting of panel of 18mm thick celuka PVC ply and for supporting the hold of shelf/ partition and shall provide 3 edges in size 18mm x 18mm as per required length the front side of the edge visible in the fronth of the self/ partition to be edge lipped by 18mm width x 1mm thick PVC sheet of density 600kg/cum manufactured by ISO 9001-2015 Certified company using solvent cement etc complete all as specified and directed. |
| 36 | S&F stainless steel shelf closing hinges 75mm size for PVC door shutters complete all as specified and directed. |
| 37 | S&F 50 x 15mm size magnet door catcher for closing for PVC door shutter complete all as specifid and directed. |
| 38 | S&F 100mm size MS mat/ glossy finish handle complete all as specfied and directed. |
| 39 | S&F modular type stainless steel cutlery basket size 20 x 19 x 4 inches (dia of wire not less than 3.00mm) of any shape withside corrosion resistance telescopic drawer channel on both side fixed with steel screws incl all fixing arrangements complete all as specified and directed. |
| 40 | All as per Srl item No.39 above but cup and saucer basket size 20 x 17 x 4 inches complete all as specified and directed. |
| 41 | All as per Srl item No.39 above but plain basket size 20 x 19 x 6 inches complete all as specified and directed. |
| 42 | All as per Srl item No.39 above but grain basket size 20 x 17 x 6 inches complete all as specified and directed. |
| 43 | All as per Srl item No.39 above but thali basket size 20 x 19 x 8 inches complete all as specified and directed. |
| 44 | All as per Srl item No.39 above but plain basket size 20 x 17 x 8 inches complete all as specified and directed. |
| 45 | S&F in repair 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed. |
| 46 | S&F repair stainless steel curtain rod with brackets 25mm dia including necesary SS clamp complete all as specified and directed. |
| 47 | Demolition of cement concrete (including floor tiles, kota stone flooring etc) (un-reinforced) of any description and in any position not otherwise specifically provided for incl remoal the demolised materials to a distance exc 50 mtr and not exc 100 mtr complete all as specified and directed. |
| 48 | M&L for 75mm thick cement concrete 1:3:6, type C1 with using 20mm graded stone aggregate in floor/ plinth protection finish the surface even and smooth without using extra cement including forming constructions joints and filling the same with bitumen filler complete all as specified and directed. |
| 49 | M&L for cement concrete type D-2 1:4:8 using 40mm graded stone aggregate) in foundation filling the mass concrete complete all as specified and directed. |
| 50 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 40mm thick bed of crushed stone, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed. |
| 51 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing debrish and rubbish off the premises and stacking serviceable tiles complete all as specified and directed. |
| 52 | M&L for scratch free, double charged, vitrified ceramic tiles 9 to 10mm thick (square/ rectangular) of 1.20 x 0.60 m in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed |
| 53 | All as per Srl item No. 52.00 above but, on vetical surface such as skirting including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed |
| 54 | M&L for Non Skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured epoxy grout for tile joint incl 15mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 55 | M&L for Glazed Coloured ceramic tiles (textured and designed as required) in vertical surfaces size 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured epoxy grout for tile joint incl 10mm thick backing coat in CM 1:3 complete all as specified and directed. |
| 56 | M&L for machine cut kota stone slab flooring 20-25mm thick laid over and including 20mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing with beeswex polish complete all as specified and directed. |
| 57 | Mirror polish on kota stone wherever required to give high glossy finish complete all as specified and directed. |
| 58 | All as per Srl item No. 57.00 here in beforebut in skirting complete all as specified and directed |
| 59 | M&L for Granite slabs (of any type) 20mm thick machine cut bedded laid over cement screed 15mm thick in CM 1:4 laid and jointed with grey cement slurry and pointed with white/ coloured epoxy grout for tile joint with admixture of pigment to match the shade of slab and polishing complete all as specified and directed. |
| 60 | Rounding to edges of stone slab slab one edge such as in steps, cooking platform, and other similar situation complete all as specified and directed. |
| 61 | S & F Vitreous China wash down water closet pedestal pattern rimless single piece size 365 x 680 x 740mm, white (include fixing bolts, flushing cistern, seat cover and flush pipe) complete all as specified and directed. |
| 62 | S&F in repair vitreous china sqatting pan (orissa pattern) size 580mm x 440mm, white with integral foot rest, any pattern including provision of cement concrete bedding (excluding fulshing cistern and flush pipe) with S or P trap, Fixed in repairs, complete all as specified and directed. |
| 63 | S&F in repair of PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed. |
| 64 | S&F Vitreous China wash basin countersunk/ under mounted type, size 605 x 410 x 200mm white, excluding taps, waste, chain and plug and porcelain stopper including brackets complete all as specified and directed. |
| 65 | S&F Vitreous China wash basin, angle back, size 450 x 300mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed. |
| 66 | S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 67 | S&F in repair 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 68 | S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 69 | S&F angular stop valves, cast copper alloy, screwed down, high pressure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 70 | S&F Long body CP Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 71 | S&F Bib taps, cast copper alloy, with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 72 | S&F Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 73 | S&F Brass CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed complete all as specified and directed. |
| 74 | S&F chromium plated shower roses 125mm sizes with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed. |
| 75 | S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 76 | S&F in repair 5.5mm thick looking mirror of size 600 x 900mm rounded edge at each mirror of selected quality glass without frame, mounted/ fitted to wall projected stainless steel studs and SS screws (4 Nos on each glass) complete all as specified and directed. |
| 77 | S&F PVC mirror cabinet of size 600 x 450mm complete all as specified and directed |
| 78 | M&L for Health faucet (ABS Bpdy) mild steel chromium plated suitable for 15mm dia pipe 1.25 M long flexible tube and ABS wall Hook including making connection and fixed in position complete all as specified and directed. |
| 79 | Taking down old GI tubing ISI marked medium grade 15mm bore with all fittings including connection etc, complete all as specified and directed. |
| 80 | Taking down old GI tubing ISI marked medium grade 20mm bore with all fittings including connection etc, complete all as specified and directed. |
| 81 | Taking down old GI tubing ISI marked medium grade 25mm bore with all fittings including connection etc, complete all as specified and directed. |
| 82 | Supplying and laying of 20mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and directed. |
| 83 | Supply and laying of CPVC brass elbow 20mm dia SDR-11 on wall/ ceiling or laying in floor complete all as specified and directed. |
| 84 | Supply and laying of CPVC brass Tee 20mm dia SDR-11 on wall/ ceiling or laying in floor complete all as specified and directed |
| 85 | Supply and laying of CPVC brass Male brass Adeptor (MTA/ MBTA) 20mm dia SDR-11 on wall/ ceiling or laying in floor complete all as specified and directed |
| 86 | Supply and laying of CPVC Ball valve 20mm dia SDR-11 on wall/ ceiling or laying in floor complete all as specified and directed. |
| 87 | M&L for GI tubing ISI marked medium grade 20mm bore with all fittings and fixed complete to walls and ceiling or laid under floor including connection etc, complete all as specified and directed. |
| 88 | M&L for GI tubing ISI marked medium grade 25mm bore with all fittings and fixed complete to walls and ceiling or laid under floor including connection etc, complete all as specified and directed. |
| 89 | Cutting chases for concealed water tubing in brick wall and making good in CM 1:3 cutting n.exc 10cm girth. complete all as specified and directed. |
| 90 | S&F in repairs incl hoisting HDPE plastic water cylindrical vertical type tanks closed top of capacity 1000 Ltrs incl 20mm bore brass stop cock and 20mm bore brass float valve with polythene float including removing the existing one complete all as specified and as directed. |
| 91 | S&F in repairs incl hoisting HDPE plastic water cylindrical vertical type tanks closed top of capacity 500 Ltrs incl 20mm bore brass stop cock and 20mm bore brass float valve with polythene float including removing the existing one complete all as specified and as directed. |
| 92 | S&F SS Sinks with drainage board in repair made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm and including waste pipe complete all as specified and directed. |
| 93 | S&F SS Sinks with drainage board in repair made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm and including waste pipe complete all as specified and directed. |
| 94 | M&L for stainless steel plate rack of size 900 x 750 x 250 made up of of 1mm thick steel complete all as specified and directed. |
| 95 | S&F in repair CP toilet paper holder complete all as specified and directed. |
| 96 | S & F in repairs PVC (SWR) Floor trap/ Nahani trap of size 140 x 140mm plain or multi with stainless steel matt finish grating with locking type, fixed to epoxy solvent cement joint dia of outlet 75mm bore complete all as specified and directed. |
| 97 | S & F in repairs 110mm bore PVC (SWR) pipes single socket in any length with rubber ring joints fixed to walls or floor or in trench complete all as specified and directed. |
| 98 | S & F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 99 | S & F 110mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 100 | S & F 75mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 101 | S & F 110mm bore PVC (SWR) bend any radius complete all as specified and directed. |
| 102 | S & F 110mm bore PVC (SWR) bend with acess door complete all as specified and directed. |
| 103 | S & F in repairs 75mm bore PVC (SWR) pipes single socket in any length with rubber ring joints fixed to walls or floor or in trench complete all as specified and directed. |
| 104 | S & F 75mm bore PVC (SWR) bend any radius complete all as specified and directed. |
| 105 | S & F 75mm bore PVC (SWR) bend with acess door complete all as specified and directed. |
| 106 | S & F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 107 | Dismantling of cast iron/ PVC pipes jointed in cement mortar 110/ 75mm bore complete all as specified and directed. |
| 108 | S & F 75mm PVC reducers PVC (SWR) complete all as specified and directed. |
| 109 | S & F 110mm PVC reducers PVC (SWR) complete all as specified and directed. |
| 110 | S & F in repairs CP 32/ 40mm Bottle trap for wash basin of having minimum water seal of 25mm. (Minimum weight 32mm-260gms/ 40mm-270gms) complete all as specified and directed. |
| 111 | S & F PVC waste pipe fixed to any type of coupling of 32/ 40mm threaded complete all as specified and directed. |
| 112 | M&L for provide PVC spout pipe of 25mm bore & 45 cm length in sunken floor cutting holes in brick walls built cement mortar and making good the dismantled portion in PCC (1:2:4), type B1 with (using 20mm graded stone aggregates) with wall finish at the disturbed portion of external surfaces complete all as specified and directed. |
| 113 | S & F in repair CP WHB mixer for mixing hot & cold water screwed down for iron pipe 15mm bore complete all as specified and directed. |
| 114 | Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 115 | M&L for 15mm thick cement plaster in cement mortar 1:6 on brick or concrete surface etc. on wall finished even and smooth without using extra cement, complete all as specified and directed. |
| 116 | M&L for rendering 15mm thick in CM 1:4 on brick or concrete surfaces finished even and smooth without using extra cement all as specified incl mixing with water proofing compound as per manufacturers instruction complete all as specified and directed. (WPC shall be measured and paid separately). |
| 117 | M&L for 10mm thick cement plaster in cement mortar 1:3 on brick or concrete surface etc. on ceiling finished even and smooth without using extra cement, complete all as specified and directed. |
| 118 | M&L for complete removal of existing treatment and preparation of old surfaces and applying two coat Acrylic emulsion with roller over applying primer and including minimum 1mm thick white wall care putty over prepared surface to achieve the surface even and smooth for painting complete all as specified and directed (Note:- primer and emulsion paint shall be carried out through air less spray machine (Mechanical means) |
| 119 | M&L for preparation of newly plastered surfaces and applying two coat Acrylic emulsion with roller over applying primer and including minimum 1mm thick white wall care putty over prepared surface to achieve the surface even and smooth for painting complete all as specified and directed. (Note:- primer and emulsion paint shall be carred out through air less spray machine (Mechanical means) |
| 120 | M&L for preparation new plastered surfaces of ceiling surfaces and applying three coats of white wash etc. complete all as specified and directed. |
| 121 | M&L for complete removal of existing treatment on ceiling surfaces including washing rubbing down and stopping of old surfaces and applying two coats of white wash etc. complete all as specified and directed. |
| 122 | M&L for complete removal of existing treament and preparation of wall, washing, scrubbing down and stopping old treatment and painted surface of plastered/ decorated surface and applying two coat of Premium Acrylic smooth exterior paint and including priming coat of exterior primer and incl one coat of wall putty complete all as specified and directed. (Note : Rate shall be included for necessary scaffolding and safety measures where required at site and painting will be done by brush/ spray/ roller). |
| 123 | M&L for newly plastered/ decrated surfaces and applying two coat of Premium Acrylic smooth exterior paint and including priming coat of exterior primer and incl one coat of wall putty complete all as specified and directed. (Note : Rate shall be included for necessary scaffolding and safety measures where required at site and painting will be done by brush/ spray/ roller). |
| 124 | Supply only liquid water proofing compound complete all as specified and directed. |
| 125 | M&L for cutting holes in brick walls built cement mortar at the starting point of down take soil/ waste pipe at any floor, fill the joint of down take pipe & trap with thick mortar in CM 1:3 and making good the dismantled portion in PCC (1:2:4), type B1 with (using 20mm graded stone aggregates) with wall finish at the disturbed portion of external surfaces complete all as specified and directed. |
| 126 | Demolition of reinforced cement concrete of any description and in any position not otherwise described complete all as specified and directed. |
| 127 | Formwork to sides and soffits of coping beam finished surfaces fair. complete all as specified and directed. |
| 128 | M&L for RCC 1:2:4 type B1 (using 20mm graded aggregate) as in Chajjas & roof slabs complete all as specified and directed. |
| 129 | M&L for taking down/ dismantled existing waterproofing treatment such as tar felt/ concrete tiles of any description from roof surfaces and removing rubbilsh to a distance not exc 100 mtrs complete all as specified and directed. |
| 130 | M&L for PCC 25mm thick (1:2:4) type B0 using 12mm graded stone aggregates mixed with integral waterproofing chemical mixed in proportion of 200ML/50Kg cement as in padding on roof surfaces for correcting/ making proper slope on roof/ chhaja and roof kerbs/ benching complete all as specified and directed. |
| 131 | M&L for cement concrete 25mm thick type B-1, 1:2:4 (12.5mm graded aggregate) using polymer triangular fibre and waterproofing compound as in roof top etc complete all as specified and directed. |
| 132 | M&L for cement concrete tiles 20cm x 20cm x 20mm thick machine pressed, set jointed neat cement slurry as on roof sarface incl cut and polished etc incl 15mm thick cement plaster in CM 1:4 complete all as specified and directed. |
| 133 | Supply & providing water proofing roof treatment with polymeric standard water proofing membrane, having 10 years gurantee for water tightness complete all as specified and described as under:-(a) Preparation of RCC roof surface and cleaning surface all as per manufaturer's specification complete all as specified and directed.(b) Supply & providing water proofing with 3mm thick APP polymeric proofing membran of 3Kg/Sqm HYPERPLAS STANDARD/ MULTIPLAS STANDARD consisting of 100micron HMHDPE film centre core including coating the surface with compatible primer and torch application of membrane with 10cm overlaps as required thereof, complete all as specified and directed. (c) Aluminium bituminous paint @1.10 Kg/Sqm shall be applied over the APP membrane surface. Note:- The work of water proofing treatment shall be got executed through expert team of manufacturers or authorised applicator of manufacturer. |
| 134 | M&L for repair to sunken floor surfaces of RCC slab by the following specifications as specified and directed:- (a) Applying acrylic cementicious polymer modified elastomeric waterproofing & protective coating like brush of fosroc or pidifin 2K (pidilite) equivalenton floors and walls as manufacturer instructions over and including 15mm thick rendering on fair faces of concrete surface in CM 1:4 in sunken portion (sides and floors) mixed with water proofing liquid and finishing the surfaceseven and smooth without using extra cement complete all as specified and directed. (Note : Water proofing liquid shall be measured and paid seperately). |
| 135 | M&L for 150mm thick PCC type B-2 (1:2:4) (using 40mm graded aggregate) as in floor finishing and making cement concrete surface even and smooth without using extra cement complete all as specified and directed. |
| 136 | Identify the cracks and construction joints, honeycomb areas in slabs/ beams/ columns, shall be chased open into 'U' groove shape and sealed with High strength, fiber based cementitious mortar, Fosroc Renderoc SP40. Providing and fixing 6-8mm dia nozzle along the joints and honeycomb areas after proper surface preparation. The injection of conbextra EP10 through the nozzle till the refusal of the grouting materials. |
| 137 | M&L for Reinforced cement concrete type B-1 (1:2:4) (20mm graded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves as complete all as specified and directed. |
| 138 | M&L for Fromwork rough finish to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 139 | M&L for concrete surface should be thoroughly abraded to remove all loose dust, dirt, laitance. Any trace of loose plaster, oil grease and any other material that might affect adhesion is to be removed by grinding/ wire brushing the surface. The entire surface shall then be washed thoroughly with plenty of water and then allowed to dry. All the dust, dirt, loose particles etc shall be removed. |
| 140 | M&L for Cleaning as directed & specified all rust/ scales/ corrosion from reinforcement bars using rust remover Reebaklens RR- Rust remover, cleaning and etching agent or equivalent, having Specific Gravity 1.16 - 1.22 @ 25°C. Reebaklens RR cleaning agent is a combination of acid based material, corrosion inhibitors and dispersing agents and is supplied as a clear green solution. Application of Reebaklens RR with brush for complete wetting of rusted metal surface and allowed to react it for 16-24 hours followed by cleaning the surface with wire brush and washing surface with fresh water as required to exposed reinforcement bars complete all as specified and directed. |
| 141 | M&L for Providing & applying inhibition coats/ system to exposed reinforcement bars after drying & also new bars after cleaning & removing scales and rust completely as specified. Nitozinc Primer Std- Two component epoxy zincrich primer or equivalent supplied in 1 and 5 Litre pack, two component system based on metallic zinc and epoxy resin which on mixing gives a grey coloured liquid. An Anti corrosive coat contents Active 'Zinc-rich' system which combats corrosion by electro chemical means. The zinch rich primer shall have specific gravity of 1.75, Solid content- 60 %, 40 microns DFT, Fully dry/ Recoatable- 45 minutes to 1 hour shall be applied at 40 microns dry film thickness and shall have salt spray resistance of <5 mg for 96 hours as per ASTM B-117 and adhesive bond strength > 1.5 MPa as per ASTM D4541. Typical application includes surface preparations by cleaning steel surface to a bright condition paying particular attention to the back of exposed steel bars, mixed two components slow speed heavy duty drill fitted with a paddle, applying unbroken coat with suitable brush and allow to dry, after 30 mins apply second coat to ensure complete cover to exposed steel/ rebar etc complete. |
| 142 | M&L for Providing and applying bond coat on the prepared surface to receive polymer modified mortar/polymer modified micro concrete, with two component epoxy based bonding coat Nitobond EP Standard- Epoxy resin concrete bonding agent or equivalent supplied in 4 Litre packs, having specific gravity 1.15 to 1.2 gm/cc, Compressive strength (BS 6319 Pt.2)- 50 Mpa at 7 days, Flexural strength strength (BS 6319 Pt.3)- 35 Mpa at 7 days, Tensile strength (BS 6319 Pt.7)- 20 Mpa at 7 days, Shear Strength (BS 6319 Pt.4)- 10 Mpa at 7 days, having an over lay time of 6 hrs and 30 ̊C, High bond strenght High bond strength : Bond strength is more than the tensile strength of good quality concrete, Barrier coat : Acts as a ‘barrier coat’ to the migration of chloride ions from host concrete. Laying of reinstatement polymer modified mortar or micro concrete shall be completed within the overlay time of bonding coat. The bond coat act as a bonding coat between old and new concrete. Typical application includes cleaning all loose dust, dirt, grease from host concrete surface by suitable means, mixing both components of bond coat by heavy duty slow speed mixer until a uniform consistency, apply unbroken coat of Nitobond EP with stiff brush covering complete area of patch repair before placing mortar or micro concrete. Item rate is inclusive of materials all labour, tools and tackles, scaffolding and transportation etc. complete as per specification and as directed by Engg.-in-charge. |
| 143 | M&L for Providing and laying Renderoc HS Xtra or equivalent - shrinkage controlled polymer modified single component, alkaline resistant fibre reinforced, thixotropic, cementitious patch repair mortar supplied in 25 kg moisture resistant bag when mixed with clean water at w:p ratio 0.18, achieves compressive strength (BS 1881 Pt.116) -> 20 Mpa at 1 day & > 45 Mpa at 28 days, Tensile Strength(BS 6319 Pt.7) > 2.5 Mpa at 28 Days, Flexural Strength (BS 6319 Pt.3)>7 Mpa at 28 days, Drying shrinkage to ASTM C 157-93, 28 days < 1000 microstrain. Typical application inclues mixing entire bag with clean water about 4.25L to 4.5 L, mixed in suitable container with heavy duty slow speed mixer machine to achieve uniform lump free mortar consistency, placing and finishing the same with trowel carefully compacting the same around the rebars and finishing to bring it in line with existing concrete surface on the beams, slabs, piles etc., where the thickness of application is less than 50mm in patches as per specification after applying bonding coat. Item rate is inclusive of materials all labour, tools and tackles, scaffolding and transportation etc. complete as per specification and as directed by Engg.-in-charge.HSE Guidelines : Recommended to wear tight-fitting, dust-resistant, chemical splash goggles and mask if airborne dust is generated, Wear protective gloves. Wear appropriate clothing to prevent any possibility of skin contact. |
| 144 | M&L for Providing and applying of single component aliphatic acrylate protective coating for concrete structures, Dekguard S or equivalent in 2 coats using suitable brush or roller on the Entire concrete surface to provide UV resistant properties & to protect concrete surface from attack by carbon di oxide, chloride ions, sulphates & water. |
| 145 | Providing & applying Nitotile EPW or equivalent hygienic, stain-resistant, with a high degree of resistance to chemical attack, abrasion and impact. Nitotile EPW is a grouting material of highest quality that provides aesthetic effect and durability, it perfectly prevents stains, spillage chemical attack to filled joints of tiles & stones (size of joints -2/3/4mm width x thickness of tiles). Compressive strength (ASTM 579)> 75 N/mm2 (7 days),Shrinkage % (ASTM D 955) < 0.1%,Tensile strength (BS 6319) >10 N/mm2 (7 days), Pot life @ 27oC 45 mins. Maximum & Light Foot traffic 24 hrs. |
| 146 | S&F facfory made single extruded WPC (Wood polymer composite) solid door/window/ceosetory windows & other frames/chowkhats size 50x100mm comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fibres (wood fibre/rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with minter joints after applying PVC solvent cement and screwed with full body threaded star headed ss screws having minimum frame density of 750 kg/cum, screw withdrawl strength of 2200N (Face) & 1100N (Edge), minimum compressive strength 58N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A catagory with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS holdfast/lugs/ss dash fastners of required dia and length complete as per direction of Engr-in-Charge. |
| 147 | S&F Facory made single extruded WPC (Wood polymer composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (suspension grade), calcium carbonateand natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kgs/cum and screw withdrawl strength of 1800N (Face) & 900N (Edge), minimum compressive strength 50N/mm2, modulus of elasticity 850N/mm2 and resistance to sread flame of class A catagory with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with SS but hinges of required size with necessary full body threaded star headed countersunk SS screw, complete all as specified and directed. |
| 148 | Supply only polyester triangular fibres as secondary reinforcement in all types of concrete and mortars complete all as specified and directed. |
| 149 | Dismantling of Pain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof coverings etc. complete all as specified and directed. |
| 150 | M&L Pre- painted galvalume aluminum zinc coating GI based profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa, hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150gm/ sqm of coating (total both surfaces) as in roof covering/ cladding to wall, including flashings, ridges valley etc fixed with self tapping screws complete all as specified and directed. |
| 151 | M&L Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa, hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150gm/ sqm of coating (total both surfaces) as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 152 | Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and directed. |
| 153 | S&F Steel work in tubular trusses, purlins etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 1979 grade St.-240 etc. complete all as specified and directed. |
| 154 | S&F Anodized aluminium Decogrille with and including suitable aluminium anodized 25 to 30 micron E/H section frame, 1.5mm thick as required with aluminium revited/ screwed attachment complete all as specified and directed. |
| 155 | M&L for 4mm thick sheet glass ordinary quality and glazing with beading/ leaping/ oil putty in square n. exc. 0.5 sqm in each complete all as specified and directed. |
| 156 | S&F Anodised aluminium frame for window and ventilator with one or more rebates including joinig cleat for fixing etc. complete all as specified and directed. |
| 157 | S&F Anodised aluminium window and ventilator shutters, fixed/ sliding/ top hung type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws all complete as per architechtural drawings and the directions of Engineer-in-charge |
| 158 | Dismantling posts or struts embedded in concrete, brick work masonry, etc. (wood, steel or RCC) any section, including taking out embedded protion and making good disturbed ground complete all as specified and directed. |
| 159 | Dismantling fencing wire mesh of any type complete all as specified and directed. |
| 160 | S & F stainless steel cloth hangers of size 29.50 x 3 x 3.5 cm with 6 No's hooks in each set fixed to wall/ doors etc with steel screws of adequate length complete all as specified and directed. |
| 161 | Excavating in trenches, soft/ loose soil n. exc 1.5m wide and n. exc1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. nexc 10sqm on plan and n exc 1.5m in depth and getting out. In soft/ loose soil complete all as specified and directed. |
| 162 | M&L for cement concrete type D-2 1:4:8 using 40mm graded stone aggregate) in foundation filling the mass concrete complete all as specified and directed. |
| 163 | M&L for Reinforced cement concrete nominal mix (1:2:4) (20mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concret, complete all as specified and directed. |
| 164 | M&L for Reinforced cement concrete nominal mix (1:2:4) (20mm graded aggregate) in columns, pillars, piers, posts and struts complete all as specified and directed. |
| 165 | M&L for Reinforced cement concrete nominal mix (1:2:4) (20mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span etc. complete all as specified and directed. |
| 166 | M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter fair finished surface complete all as specified and directed. |
| 167 | Formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete, square, rectangular or polygonal in shape, complete all as specified and directed. |
| 168 | Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc |
| 169 | Returning, filling in, soft/ loose soil including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed. |
| 170 | Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed. |
| 171 | M&L for 40mm thick 1:2:4 type B0 damp proof course in horizontal or vertical surfaces including necessary frame work complete all as specified and directed. |
| 172 | S&F TMT bars 8 to 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. |
| 173 | All as per Srl item No.172.00 herein before but 5mm dia and over and including 10mm dia in stirrups, spacers and binders. |
| 174 | M&L for Precast Cement concrete 1:2:4 Type B0 (Using 12.5mm graded stone aggregate) in 35mm thick Jallies or louvers including all mouldings complete and set in Cement Mortar 1:4 complete all as specified and directed. |
| 175 | M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces and finishing surfaces even and smooth without using extra cement complete all as specified and directed. |
| 176 | M&L for thick PCC 1;3;6 type C-1 (using 20mm graded stone aggregate) as in copping like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 177 | M&L for preparing newely plastered surface of wall and applying finishing walls with acrylic smooth exterior paint of required shade. New work two or more coat applied @ 1.67 ltr/10 Sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified and directed. |
| 178 | M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed. |
| 179 | S&F Fe 410 -W (Gde- E- 250) quality- A framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed. |
| 180 | S & F 1.60mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, weded to steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required. |
| 181 | M&L for two coats of synthetic enamel paint over primer incl preparation of steel surfaces complete all as specified and directed. |
| 182 | M&L for 20mm thick Granite (of any type) tiles machine cut in skirting/ dado laid over cement screed bedding layer or mortar 15mm layer of mortar 15mm thick for laying floor finishes in CM 1:4 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified and directed. |
| 183 | Demolition and breaking up drain pipes 150mm dia (Salt Glazed ware, AC or reinforced concrete) set in cement motar etc. comlplete all as specified and directed. |
| 184 | Demolition of cement concrete (un-reinforced) of any description & in any position not specifically provided for comlplete all as specified and directed. |
| 185 | Demolition of reinforced cement concrete (reinforcemen cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and directed. |
| 186 | M&L for TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. |
| 187 | M&L for Pre-cast cement concrete (1:2:4) type B-1 using 20mm graded stone aggrgates) set in CM 1:4 as in landing, cover slab (for manholes etc) chulla hoods, chajjas, water trough, mangers, shelves and similar article with plain faces including form work complete all as specified and directed. |
| 188 | M&L for cement concrete (1:2:4) type B-1 using 20mm graded stone aggrgates as in coping, chajja kerbs, roof padding/ staging of water tank etc. including necessary fromwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 189 | M&L for cement concrete type D-2 1:4:8 using 40mm graded stone aggregate as in foundations and mass concrete complete all as specified and directed. |
| 190 | M&L for 150mm dia salt galzed stone ware (SGSW) drain pipe, grade 'A' laid in trenches and jointed complete all as specified and directed. |
| 191 | M&L for cement concrete type B-2 1:2:4 using 20mm graded stone aggregate as in surface channels and drains complete all as specified and directed. |
| 192 | M&L for cement concrete 1:3:6 type C-2 for 150mm dia in bed to drain pipes including packing under, and haunching against the sides of pipes etc complete all as specified and directed. |
| 193 | Removing excavated material/ Debries obtained from demolition to a distance not exc. 50 m and depositing where directed etc. complete all as specified and directed. |
| 194 | Taking down carefully copper/ aluminium point wiring (light, fan, sockets or power) complete including all fitings and fixtures such as switches, sockets, ceiling roses, pendens, regulators, light fittings etc, removing matrials to store for taking credit and making good disturbed surfaces complete all as specified and directed. |
| 195 | Taking down carefully copper/ aluminium sub-main wiring any type and making good the disturbed surface of walls and floors etc complete all as specified and directed. |
| 196 | Taking up/ down existing single phase electric energy meter of any capacity after disconnecting all necessary electrical connections and re-fixing after work complete all as specified and directed. |
| 197 | Taking down existing ceiling fan and exhaust fan of any size and re-fixing the same after B/R work including servicing/ overhauling, winding of the fan, replacement of defective parts, painting of the complete fan with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and writing MES Number in black paint with skilled painter and providing three core flexible copper cable for connection from ceiling rose/ connector complete all as specified and directed. |
| 198 | Taking down existing geyser any size in position and re-fixing the same after B/R work including painting of the same with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and writing MES Number in black paint with skilled painter, with and including providing three core flexible copper cable for connection from ceiling rose/ connector complete all as specified and directed by Engr-in-Charge. |
| 199 | M & L for Point wiring with 1.5 Sqmm (nominal cross sectional area), single core, PVC insulated with multistranded PVC unsheathed FRLSH copper conductor cable in and including rigid non- metallic PVC concealed conduit of suitable size medium grade ISI marked complete, including one continuity earth wire of PVC insulated, unsheathed 1.5 Sqmm (nominal cross sectional area) FRLSH copper conductor connected to all fittings, common earth and connected to earth dolly including modular flush box with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches and blank plates of suitable size all fittings and accessories and making good disturbed surface of walls and floors etc., complete all as specified and directed for the following:- |
| 200 | One light/ fan/ bell controlled by one, one way switch 5/6 Amps |
| 201 | One light/ fan/ bell controlled by one, two way switch 5/6 Amps |
| 202 | One 3 pin, 5/6 Amps socket outlet point on independent board controlled by one, one way 5/6 Amps switch |
| 203 | One 3 pin, 5/6 Amps socket outlet point on same board controlled by one, one way 5/6 Amps switch |
| 204 | M & L for Point wiring with 2.5 Sqmm (nominal cross sectional area), single core, PVC insulated with multistranded PVC unsheathed FRLSH copper conductor cable in and including rigid non- metallic PVC concealed conduit of suitable size medium grade ISI marked complete including one continuity earth wire of PVC insulated, unsheathed 2.5 Sqmm (nominal cross sectional area) FRLSH copper conductor connected to all fittings, common earth and connected to earth dolly for one three pin 15/16 Amps socket out-let point on an independent board including modular flush box with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches and blank plates of suitable size and making good disturbed surface of walls and floors etc. complete all as specified and directedNote:- Make of GI flush box should be same with switch/ socket |
| 205 | S&F for Ceiling rose, surface bakelite with three terminals ISI marked, AC, 50 HZ, 230V, complete all as specified and directed. |
| 206 | S&F modular switch 1 way 6 A, 1 module, complete all as specified and directed. |
| 207 | S&F modular switch 2 way 6 A, 1 module, complete all as specified and directed. |
| 208 | S&F modular socket 6 Amps 2/3 pin combined 2 module, complete all as specified and directed. |
| 209 | S&F switch modular type 16 A, 1 module, complete all as specified and directed. |
| 210 | S&F socket modular type multipurposes 6/16 A, 2 module, complete all as specified and directed. |
| 211 | S&F modular bell push flush type, 5 Amp complete all as specified and directed. |
| 212 | S&F lamp holder insulated body with back plate for batten fittings, complete all as specified and directed |
| 213 | S&F Buzzer Ding Dong AC 230 Volt single pole, complete all as specified and directed |
| 214 | Supply and fixing Inverter LED batten 20 watt with squre profile and polycarbonate channel. Lithium lon battery with charging time 8 hourse -10 hourse and back up time upto 3 hours. with extruded environmental friendly, energy efficient with three core flexible copper conductor cable of suitable size from ceiling rose complete with all connected accessories complete all as specified and directed. |
| 215 | S & F for Energy saving new generation environmental friendly long life versatile LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including necessary mounting arrangements and provision of 2.5 Sqmm three core copper conductor cable multi stranded from ceiling rose to light fitting and necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts including taking down old unsv complete all as specified and directed. |
| 216 | Supply and fixing 10W LED 6500K lights fitting Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient with three core flexible copper conductor cable of suitable size from ceiling rose complete with all connected accessories, complete all as specified and directed. |
| 217 | S&F for Decorative wall mounted luminaire made out of polycarbonate with unbreakable globle suitable for LED bulb and provision of LED bulb 10 watts including taking down old unsv complete all as specified and directed. |
| 218 | S&F LED bulb of 7 watt, of base B-22, 6500 K suitable for fixing in lamp holder, complete all as specified and directed. |
| 219 | S&F LED light fitting 1 x 9W/ 1 x 10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including taking down old unsv, complete all as specified and directed. |
| 220 | S&F of TPN DB 4 way dounle door with 200 Amp rated bus bar, 415 volts 50 Hz including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonary etc including taking down old unsv and making good of disturbed surface to match with existing colour of wall complete all as specified and directed. |
| 221 | S&F of TPN, 63 Amp 415V 10KA 'C' curve, mainiature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning by using lugs including taking down old unsv, complete all as specified and directed. |
| 222 | S&F of MCB DB SPN 8 way dounle door with 200 Amp rated bus bar, 415 volts 50 Hz including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonary etc including taking down old unsv and making good of disturbed surface to match with existing colour of wall complete all as specified and directed. |
| 223 | S&F in replacement 32 Amp rating 240V 10KA 'C' curve, mainiature circuit breaker (MCB) of SPN 32 Amps and current carrying capacity in the MCB DB complete with connection testing and commissioning by using lugs, complete all as specified and directed. |
| 224 | S&F in replacement 240V 10KA 'B' curve, mainiature circuit breaker (MCB) of single poles current carrying capacity 5 to 32 Amp in the MCB DB complete with connection testing and commissioning by using lugs, complete all as specified and directed. |
| 225 | M&L for single pole and earth encolsure with a two pin and earth plug with socket 240 volts 50 Hz complete with one single pole MCB SP 20 Amps including taking down old unsv complete all as specified and directed. |
| 226 | M&L for Sub main wiring with 04 runs of 6 Sqmm main wire along with 02 run of 06 Sqmm earth wire (green in colour) single core FRLSH PVC insulated unsheathed 1100 volts grade, ISI marked multistranded copper conductor cable, drawn through and including adequate size rigid non-metallic PVC concealed/ surface conduit (medium grade) wherever necessary with all fittings & accessones including cutting chases for conduits as required, sinking for terminal box, making good the same including taking down old unsv sub main wiring complete all as specified and directed.Note:- Four runs of main copper conductor, two run of earth wire and one run of PVC conduit shall be measured as one unit length. |
| 227 | M&L for Sub main wiring with 02 runs of 4 Sqmm main wire along with 01 run of 04 Sqmm earth wire (green in colour) single core FRLSH PVC insulated unsheathed 1100 volts grade, ISI marked multistranded copper conductor cable, drawn through and including adequate size rigid non-metallic PVC concealed wherever necessary with all fittings & accessones including cutting chases for conduits as required, sinking for terminal box, making good the same including taking down old unsv sub main wiring complete all as specified and directed.Note:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length. |
| 228 | S&F for exhaust fan, steel body AC single phase 230 volt of size 300mm sweep complete with blade, frame and louver including taking down old unsv exhaust fan and deposit the same in the AGE E/M-III store complete all as specified and directed. |
| 229 | Supply & Fix plastic body exhaust fan AC single phase 230/ 240 V of size 200mm sweep with louver, white in colour including cutting of wall and duly connection with copper wire from ceiling rose, including taking down and old unserviceable exaust fan deposit to E/M Store complete all as specified and directed. |
| 230 | S&F of ceiling fans complete with blades, down rods 15mm/ 12mm upto two mtr, run with electronic regulator or remote with battery and complete accessories, 230 V, 50Hz, 1200mm sweep and rated power 26W (+ 10%) and rate speed 350 RPM (+ 10%) Min air delivery 210 CFM with service value shall not be less than 8.00 BEE as per BIS. Five star rated with brushless direct current motor (BLDC), painting to match with existing surfaces including taking down old unsv fans and deposit the same in the MES store complete all as specified and directed. |
| 231 | S&F for electric water heater storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 ltrs, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV connection pipe etc. necessary electrical connection including taking down and safe deposit of old unsv Geyser to E/M store complete all as specified and directed. |
| 232 | M&L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6mm thick, buried directly in ground vertically to a depth not less than 2.25 meters deep below ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level connect to galvanised earth lead wire of 4.0 Sqmm size by means of bolts, nuts, check nuts and washers of galvanized iron or steel up to 7.5 meter length including connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber, 40mm thick RCC cover 1:2:4 mix with 6mm dia nominal reinforcement @ 150mm c/c both ways etc complete all as shown in electrical plate No.5, connected to earthing test point complete including testing on completion all as specified. incl taking down old unsv earthing complete all as specified directed. |
| 233 | Supply & laying and testing commisioning cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 core laid in pipes, trenches/ ducts on poles including taking down old unsv XLPE cable, complete all as specified directed. |
| 234 | Supply and laying jointing GI pipe light grade 50mm bore trenches/ under floor or roads/ along poles/ on walls incl clamps for protection of cable incl fittings complete all as specified and directed. |
| 235 | Excavation in trenches not exc. 1.5m wide and not exc 1.5m deep in hard/ dense soil and getting out complete all as specified and directed. |
| 236 | M&L for filling approved fine crusted sand in trenches as cable cushion to the full width of excavated trench, under and over cable complete all as specified and directed.(Note : Punned thickness of sand shall be measured) |
| 237 | M&L for bricks slightly over burnt (kiln burnt), modular bricks, best quality, locally available, laid flat, dry, laid in trenches along the length of cable transvarsally with width equal to length of brick for cable protection complete all as specified and directed. |
| 238 | S&F in repair for modular fan regulator step type, 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and directed. Please Enable Macros to View BoQ information |
| 239 | S&F in repair for modular fan regulator step type, 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and directed. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
| 6 | Click here to download tender document | Tender Documents |
| 7 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
