Tender For Renovation Of 5 No. Rooms (Room No. 01 To 05) With Electrical Installation Works, Furnishing Alongwith Up-Gradation Of Kitchen At Pehowa Tourist Complex, Kurukshetra., Pehowa-Haryana

TDR : 55185563

Tender Notice
BOQ

20 Days Left

Pehowa , Haryana

Tender Brief : Tender For Renovation Of 5 No. Rooms (Room No. 01 To 05) With electrical installation Works, Furnishing Alongwith Up-Gradation Of Kitchen At Pehowa Tourist Complex, Kurukshetra.

Document Fees
₹ 1180 /-

EMD
₹ 364100.0 /-

Tender Value
Refer document

Submission Date
13-05-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	P/F shower basket small (ACN-CHR-1177N) complete in all respect as per satisfaction of EIC.
2	P/F exposed part kit of single lever basin mixer wall mounted consisting of operating lever, cartidge sleeve, wall flange, nipple and spout (compatible with ALD-233N and ALD-235N) (OPP-CHR-15233NKPM) complete in all respect as per satisfaction of EIC.
3	P/F Dorset make Nika Model-handle on rose of SS comp. in all respects, P/F mortice latch of SS Dorset make Art. No. ML 103 comp. in all respect.
4	P/F door stopper dorset make DSHT-door mounted hanging type comp. in all respects.
5	P/F coat double hook cat. No. AKB 35761 (Jaquar make KUBIX F series) comp. in all respect as per satisfaction of EIC.
6	P/F door back rubber complete in all respect as per door set.
7	P/F C.P. brass extension piece 15 mm (heavy) i/c cutting and wastage etc.
8	P/F jet spray set for regular constellation cascade multi jet art no.-7016 size 15x900 mm of viking complete in all respect.
9	Pdg. rubbing and polishing on Kota stone on existing flooring complete in all respect
10	P/F 35 mm thick factory manufactured flush doors shutter of century/green ply make with both sides laminated complete in all respect.
11	P/F CP brass odonil container with wall flange high lifemake KUBIXF series complete in all respect
12	Dismantling of wall tiles, scraping of plaster, removing of old G.I and H.C.I. pipes, sanitery wave, CP fittings, door and windows with chowkets and dispose off disablemented material etc. complete in all respect.
13	provision for shower curtains as per drg. and design including MS Rod
14	Providing and fixing of paris false ceiling with GI suspenders using fasteners and frame work with GI members using best quality wire meh (23 gauge with 12 squares per inch) with 12 mm POP Plaster approved quality Sakarni odhar shri make cornice, beading, if any including two coats of plastic emulsion after preparation of surface, priming coat to the full satisfaction of the EIC (i) main member will be of 20 gauge @ 2’-0” (ii) secondary member will be of 24 gauge 3’-0” (iii) cutting of holes for electric fitting as per drawing and design (iv)work will be executed as per drawing and design (v) floor area of false will be measured, no extra area will be paid of offsets and Dome etc.)
15	P/F SS bearing hinges Dorset make of SB Art. No. HG 1151 (102x76x3.5x12) comp. in all respects as per satisfaction of EIC.
16	Providing and fixing P/F Concealed body for single lever basin mixer wall mounted but without exposed parts (ALD-CHR-233N) Jaquar make complete in all respect as per satisfaction of EIC.
17	P/F Dorset make Nika model-handle 10” CY of SS comp. in all resects, P/F Doorset cylinder of SS both side key 60mm Art. No. CL200 and Doorset Art. No.ML 110 comp. in all respect as per satisfaction of EIC.
18	P/F Elena prime vertical (manual) 25ltr.(EPM-WHT-V025) Geyzer `Jaquar make` Complete in all respect .
19	P/F Angular stop cock with wall flange (OPP-CHR-15053PM) Complete in all respect (N.S) (Jaquar Make).
20	P/F 450 MM long Braided hose with Two nuts and Rubber Washers Without Nipple (Suitable for geysers) (ALD-CHR-805B) Complete in all respect (N.S) Jaquar make
21	P/F Shower arm 20mm dia and 300mm long round shape with 900 bend for wall mounted showers with stainless steel flange (SHA-479L300s) Complete in all respect (N.S) Jaquar make
22	P/F Over head shower 120 mm Round shape Single Flow (ABS Body Chrome Plated with Grey Face Plate) with Rubit Cleaning System(OHS-CHR-1789) Complete in all respect (N.S) Jaquar make
23	P/F Concealed body for single lever high flow diverter with button assembly, but without exposed parts (ALD-CHR-079N) Complete in all respect (N.S) Jaquar make
24	P/F Single lever exposed parts kit of hi- flow (OPP-CHR-15079NKPM) Diverter Consisting of Operating Lever, Cartridge Sleeve, Wall Flange( with Seals),Button Assembly Sleeve and Button (Compatible with ALD-079) Complete in all respect (N.S) Jaquar make
25	P/F Towel Rack 600mm long with lower hangers,Stainless steel (AKP-CHR-35781PS)Complete in all respect (N.S). Jaquar make
26	P/F Corner glass self with bracket (ACN-CHR-1173) Complete in all respect (N.S) Jaquar make
27	P/F Single piece slim concealed cistern body with installation Kit and `S- Type` drain pipe connection set for Wall Hung WC (without Flush Control Plate) (JCS-WHT-2400S) Complete in all respect (N.S)Jaquar make
28	P/F Control Plate Opal (JCP-CHR-152415) Complete in all respect (N.S) Jaquar make.
29	P/F Rimless, Blind Installation Wall Hung WC in white Matt With UF Soft Close Slim seat cover, Hinges and Accessories Set,(SLS-WHM-6953 BIUFSM) Size-375x520x400 mm Complete in all respect (N.S) Jaquar make
30	P/F 2 way Bib Cock with wall flange (OPP-CHR-15041PM) Complete in all respect.(Jaquar make)
31	P/F Hand Shower (Health Faucet) with 8mm dia, 1.2 meter long flexible tube and wall hook (ALD-573) Complete in all respect.(Jaquar make)
32	P/F Toilet roll holder with stainless steel Flap (ACN-CHR- 1153S) Complete in all respect (N.S) Jaquar make
33	P/F Regular body of Concealed stop cock Suitable for 15mm Pipe Line with Protection Cap (without Exposed Parts) (ALD-CHR-083) Complete in all respect (N.S) Jaquar make
34	P/F Table top basin Size 485x370x150mm (SLS-WHT-6901) Complete in all respect (N.S) Jaquar make
35	P/F Waste coupling 32 mm full thread with 80 mm height (ALD-CHR-705) Complete in all respect (N.S) Jaquar make.
36	P/F Bottle Trap 32 mm size with 300mm and 190mm Long Wall -connection Pipes and wall flange (ALD-CHR-769L300X190) Complete in all respect (N.S) Jaquar make
37	P/F Towel ring square with Round Flange (ACN-CHR-1121N) Complete in all respect (N.S) (Jaquar make)
38	S/E of CATA exhaust fan with existing fan point complete in all respect as per satisfaction of E.I.C. (Make Havells vento jet , Crompton, Bajaj, Orient).
39	S/E of mirror light with lamp required labour and material complete in all respect as per satisfaction of E.I.C. (BASIC cost : Rs 2500/- as approved by architect)
40	S/I/T/C of 9 Fin. 2000 Watt PTC Room Oil Based Heater with Fan including making connection with required labour and material complete in all respect as per satisfaction of E.I.C. (Make Havells, Bajaj, usha).
41	S/E of strip/Rope light IP65 including driver etc required labour and material complete in all respect as per satisfaction of E.I.C. (make : havells, wipro, Philips)final
42	Deep Cleaning of floors and tiles area complete in all respect as per satisfaction of EIC.
43	S/I/T/C of Advanced R.O with RO plus UF plus TDS control plus UV LED Tank of capacity 8 L and 20 LPH flow with 1 year complete warranty. complete in all respect as per satisfaction of EIC (Make - Kent, Aquaguard, LG)
44	P/F of Hard Top Deep Freezer (500 Litres) BEE 5 star rating, double door, convertible deep freezer, dual heavy duty condensor, 70mm PUF thickness, 4 years comprehensive warranty . complete in all respect as per satisfaction of EIC (Make - Haier, Blue Star, Western Model- HFC-500DM5
45	S/I/T/C of Air Curtain with Sensor and Remote - 410 W (Size 3 Feet) Capacity 0.9 cubic metres, Special Feature Remote Controlled, Product Dimensions 23D x 90W x 22H Centimeters BEE Star Rating 3 Star complete in all respect as per satisfaction of EIC Make: DOLPHY, Eureka, Mitsubishi
46	S/I/T/C of Air Curtain with Sensor and Remote - 700 W (5 Feet) Capacity 1520 litres, Cooling Power 700 Watts, Special Feature Remote Controlled, Product Dimensions 22D x 150W x 23H Centimeters complete in all respect as per satisfaction of EIC Make: DOLPHY, Eureka, Mitsubishi
47	Curtains as per approved colour scheme. PLEATED Curtain cloth as per approved colour scheme (fixed with channel) Lining cloth of superior quality . Width of the curtain should be 1’-6”after pleating and finished height 8’-6” ht. complete in all respect.
48	New Runner above Bed CoverApp. Size 98” x 30” with foam quilting. Cloth as/app. Colour scheme. Lining cloth of superior quality. Stitching lines as approved
49	Cushions as/app. Colour scheme with polyfill fillers of superior quality make Recron Certified Microfibre and Ultra Fine Polycot.16”x16” size Cushion cloth As/app. Colour scheme...
50	P/F Table lamp. Readymade to be selected as per the décor of the room.
51	P/F Wall Painting with framing (Modern art/Nature theme prints with frame as/selected design and concept. Size: 1’-6”x2’-0”..
52	P/F Hotel DND sign panel -Dimensions ( LW H) 150215*15mm millimeter complete in all respect.
53	P/F MIFARE RFID card lock system Japanse lock motor ( HSN Code-8301409,8523599 and 85235100 ) as per satisfaction of EIC complete in all respect with mechanical key Silver Finish.
54	NS Item -Center Table with quartz Top Size:- 2`x2’x1½” T.W. frame of required section out of 2 ½”x1 ½” all around and duly polished as/app colour scheme. Leg as per design using teak wood sections out of 3”x3” as required to give proper shape and strength. Melamine Polish in semi matt finish as per approved colour scheme.Teak wood frame out of 3”x1 ½” fixed with legs on four side finish as/app. complete in all respect .
55	NS Item -Wooden Study ChairMade of Teak wood member of required section finish as approved. 3`th foam of 40 density over 1/2`th ply on seat and 1 plus 1/2`th foam of 32 density with necessary required material. Teak wood frame members below the seat should be out of 3`x1/2` with triangular corners inside.Teak wood legs, arms and back supports as required to given proper shape as per drawing.Framework to be furnished with melamine/semi matt polish complete in all respect.
56	NS Item -Supply of LED pendent light with black/white powder coated aluminium housing and pressure die-cast heat sink having high efficiency.THD (10% (minimum 2 Year warranty)complete in all respect with required labour and material as per satisfaction of Engineer-in-Charge. make havells, Phillips, Crompton.(Ref Model: Havells UNECOPENDDLP8WLED830S24BLK-G2)8 W
57	`NS Item - Supply of LED pendent light with black/white powder coated aluminium housing and pressure die-cast heat sink having high efficiency.THD (10% (minimum 2 Year warranty)complete in all respect with required labour and material as per satisfaction of Engineer-in-Charge. make havells, Phillips, Crompton.(Ref Model: Havells UNECOPENDDLP8WLED830S24BLK-G2)20 W `
58	`NS Item -Supply of LED Surface COB Downlighter surface light with black/white powder coated aluminium housing and pressure die-cast heat sink having high efficiency.THD (10% ((minimum 2 Year warranty) complete in all respect with required labour and material as per satisfaction of Engineer-in-Charge make havells, Phillips, Crompton,halonix. (REF MODEL: UNECOSURFDLS8WLED830S24BLK-G2)8 Watt `
59	`NS Item -Supply of LED Surface COB Downlighter surface light with black/white powder coated aluminium housing and pressure die-cast heat sink having high efficiency.THD (10% ((minimum 2 Year warranty) complete in all respect with required labour and material as per satisfaction of Engineer-in-Charge make havells, Phillips, Crompton,halonix. (REF MODEL: UNECOSURFDLS8WLED830S24BLK-G2)15 Watt `
60	`NS Item -Supply of LED Recessed COB Downlighter energy saving, aesthetically designed, recessed mounted down light with 15° tilt pressure die-cast aluminum heat sink and high efficiency long life COB LED mounted on MCPCB with high efficacy for enhanced lumen output. THD (10% (minimum 2 Year warranty) complete in all respect with required labour and material as per satisfaction of Engineer-in-Charge make havells, Phillips, Crompton, halonix. (REF MODEL: UNECOSURFDLS8WLED830S24BLK-G2)8 Watt `
61	`NS Item -Supply of LED Flood light and street light energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. Having Lumen output)= 120 Lumen/per watt and efficiency of 0.9 make havells, Phillips, Crompton, Halonix.100 W street Light `
62	`NS Item -Supply of LED Flood light and street light energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. Having Lumen output)= 120 Lumen/per watt and efficiency of 0.9 make havells, Phillips, Crompton, Halonix.200 W Flood Light `
63	`NS Item - S/E of heavy duty 380mm exhuast fan (minimum 2 Year warranty) complete in all respect with required labour and material as per satisfaction of Engineer-in-Charge make havells, bajaj, crompton (ref model : havells Turbo force 1P) `
64	`NS Item -S/E of BLDC DECORATIVE Ceiling Fan 1200 MM with required labour and material in existing fan point complete in all respect as per satisfaction of E.I.C. (Make Havells enticer BLDC or same in Crompton, Bajaj). `
65	`NS Item -S/E of decorative Single wall braket light with lamp required labour and material complete in all respect as per satisfaction of EIC. (Basic cost: Rs. 1000/- as approved by architect). `
66	`NS Item -Supply of POST TOP Luminare of 40 W energy saving, environment friendly, long life aesthetically designed with symmetrical light distribution, die-cast aluminium landscape luminaire with high power LED as light source. Unique ring shape LED Engine ensuring soothing, glare free light distribution complete in all respect with required labour and material as per satisfaction of Engineer-in-Charge make havells, bajaj, crompton (Equilant to model : havells IMBOLPT40WLED730SYMPCGRYCMP) `
67	P/Fixing Cupboard with lugage rack plus fridge unit plus Tea Kettle Shelf. As/Drg. Size:8’-3” x2’-0”x6’-9”. ½” HDHMR board for back, top and bottom finish with 1 mm th. laminate as/app on all exposed area. 1 mm Th. laminated top on luggage rack and fridge unit as/app shade over ¾” HDHMR Board below it finished with teak wood member/ lipping as/app. Front shutters, internal partitions, internal shelves and other visible portions/Shelves to be finished with 1 mm laminate. All necessary hardware of Hafele, Hattic and Dorset make. S.S. handle should be 18” long of superior quality as approved. Provision of automatic light with sensor on the cupboard shutters. Shelf in ¾” Th. Board with laminate finish with teak wood lipping on edges. As/drg. One shelf in ¾” Th. Board with provision of wooden Holders for glasses as/drawing. Above 6’-9” ht. HDHMR board should be of century/green/ Action Tess.
68	Double Bed with Bed Head plus bed platform with footrest. (mattress size 36”x75”) 9’-8”x3”x4’-6” (bed head size) 6`-2`x6`-3`x1`-2` (Bed platform size) 5 mm th. Teak Ply as per approved colour scheme over ¾ ” thick HDHMR Board with melamine polish in semi mat finish and teak wood lipping on edges. Finish as/approved. Upholstery as approved on the Bed Head over 1” th. foam over Ply/Board finish as/approved. Foot rest made of ¾” th. HDHMR board with 5 mm th. teak ply as per approved colour scheme plus teak wood lipping on edges with melamine polish in semi mat finish as/app. Platform to have 12mm thick HDHMR ply of with 1 mm th. laminate on it over Hollock wood frame out of section 3`x1 ¾” finish as/approved shade. Side members 11”x ¾” made of Board with teak ply finish with teak wood beading on edges and Teak wood leg support out of 3” X3” finish
69	Bed side table 1’-6”x1’-4”x1’-9” Made of ¾” th. of HDHMR Board of century/green/Action Tessa make with teakwood beading on edges fixed over as/app design teak ply on all exposed faces and 1 mm laminate on internal faces. Table to have two drawer with soft touch channels of Hafele, Hattic and Dorset make. Front facia of drawers in Teak ply polish as/approved with S.S Handle on the board. Teak wood leg supports out of 2”x 1 ½”finish as/app. Design to match the bed as per approved. Polish melamine in semi mat as /app shade and finish.
70	Easy Chair With arms and with round back. 2’-6”x2’-5”x2’-9” seat height should be 1’-5”. Upholstery as per approved colour scheme. 4” thick foam of 40 density on seat and 2 ½” thick of 32 density on back over required spring base for seat and back over frame work made of soft wood leg as per design using teak wood sections for outer/exposed members required to give proper shape and strength. Polish as per approved complete in all respect.
71	P/F of stainless steel triple sink unit Grade 304 food grade for kitchen in Tourist Complexes complete in al respect as per satisfaction of EIC.
72	P/F of Flying insect killer mild steel body high-voltage fly insect killer machine, machine body, mild steel, fitting wall/ceiling, power used:55W U.V Tubes: 2 Nos. 2 Feetx 18w, open area: 300 SQ. Ft Closed Area: 600 SQ FT Dimension:630 x 120 x 360 mm complete in all respect as per satisfaction of EIC. Make: PESTOP.
73	P/F of stainless steel plain (food grade SS-304) water cooler, having cooling capacity of 40 ltrs per hour and storage capacity of 80 L voltage overload protection, silent operation and comprehensive warranty of 1 year complete in all respect as per satisfaction of EIC Make: Blue star, Model 4080B.
74	P/F of wall mounted water heater of 25L capacity, glass coasted anti rust tank and heavy duty heating element with warranty of 5 years on tank . complete in all respect as per satisfaction of EIC. Make: Haier, Havells, Jaquar, Model- Monza.
75	P/F of commercial hand blender low noise power-7000 wattage complete in all respect as per satisfaction of EIC. Make Sujata, Havells, Philips
76	B0647 SS Mosquito Jali (12x26) grade 304................
77	B0979 MS Plates, angles, channels etc. i/c fabrication..................
78	P/F OPAL prime bath tub spout with flange (SPJ-CHR-15429PM) Jaquar make complete in all respect as per satisfaction of EIC......
79	P/F fancy looking mirror (Modigulard) beveled edges comp. in all respect as per satisfaction of EIC......
80	P/F tower bolt of SS round dia-10 (TBR 4`) comp. in all respects as per satisfaction of EIC. (dorset make).
81	P/L vitrified tiles 6`-0` x 4`-0` of Kajaria/Nitco/Johnsons/Somany make premium quality with adhesive 3 mm thick using 5KG adhesive per sqm i/c fitting joints complete in all respect as per satisfaction of EIC. (floor tiles for room ) ( Design drawing will be got priorly approved by EIC................
82	P/L vitrified tiles 4`-0` x 2`-0` of Kajaria/Nitco/Johnsons/Somany make premium quality with adhesive 3 mm thick using 5KG adhesive per sqm i/c fitting joints complete in all respect as per satisfaction of EIC. ( wall tiles for bath ) ( Design drawing will be got priorly approved by EIC............
83	P/F CP jali chilli make complete in all respect as per satisfaction of EIC................
84	New Long Mirror (Size 2’-0”x4’-6” ht.) Teak wood frame out of 2 ½” x 1 ½” section duly polished in melamine / semi matt finish cornice, 4 mm thick mirror, over 12 mm thick HDHMR Ply duly fixed on wall as shown in the layout plan...............
85	P/F Channel for curtains of high standard quality approved by authorities. complete in all respect. (Channel for main Curtains and Sheer Curtain)................
86	6” Th. pocketed Spring Mattress of size 36”x75” Sleepwell/Spring fit, Kurl on and Peps foam make. Complete in all respect ...............
87	Persian Carpet for Drawing room to be selected by Architect 2`-6` x 5`-0`
88	Providing and Fixing of Juicer Mixer Make-Hamilton/JTC commercial Heavy Duty Juicer complete in all respect as per satisfaction of EIC.
89	P/F of Heavy duty 4 slice Popup toaster, power min 1350 Watts. complete in all respect as per satisfaction of EIC (Make Russel Hobbs/ Havells/Morphy Richards).....
90	P/F of commercial sandwich griller jumbo (4 bread slice) minimum 1800 watts stainless steel and warranty of 2 years complete in all respect as per satisfaction of EIC (Make Havells, Prestige, wonderchef).
91	P/F of Advanced 5 stage filter R.O for water cooler with 1 year complete warranty complete in all respect as per satisfaction of EIC Make: OEM.
92	[10.100.1]Cement Concrete 1:8:16 Flooring 1. Cement Concrete 1:8:16 with Over burnt (Jhama) Brick Aggregate: 90 mm to 40 mm size in foundation and plinth. [Through Rate]
93	[10.37.1]Providing and fixing of Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 1. 25 mm thick [Through Rate]
94	[10.50.1]Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 1. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. [Through Rate]
95	[10.58]Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. [Through Rate]
96	[10.63.2]Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 2. Size of Tile 600x600 mm [Through Rate]
97	[10.7]Providing and laying of conglomerate floor 50mm thick cement concrete topping 1:2:4 [Through Rate]
98	[10.70.2]Extra for grouting the joints of floor tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. 2. Size of Tile 600x600 mm [Through Rate]
99	[10.9]Providing and laying of Conglomerate floor 25 mm thick cement concrete 1:2:4 on 100 mm cement concrete 1:8:16 and 100 mm sand or stone filling. [Through Rate]
100	[10.93]Providing and Laying of P.O.P on floors with polythene sheet, cleaning, wiping floor and mixing of POP with water on the polythene sheet and removing it after completion and disposing off the same complete in all respects as per direction of Engineer-in-Charge. [Through Rate]
101	[11.17]Providing and fixing of chicken wire mesh for avoiding cracks in plaster with necessary nail/screws etc. complete in all respect to the entire satisfaction of engineer-in-charge [Through Rate]
102	[11.5.4]12 mm cement plaster of mix : 4. 1:6 (1 cement: 6 fine sand) [Through Rate]
103	[11.52]Cement rendering on plaster 1 mm thick [Through Rate]
104	[11.6.1]15 mm cement plaster on the rough side of single or half brick wall of mix : 1. 1:4 (1 cement: 4 fine sand) [Through Rate]
105	[11.60]Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. [Through Rate]
106	[11.67.1]Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 1. Water thinnable cement primer [Through Rate]
107	[11.71.1]Wall painting on a cement plaster surface with acrylic emulsion paint of approved brand and manufacture to give an even shade : 1. Two or more coats on new work [Through Rate]
108	[11.82.1]Painting the wooden / metal surface with synthetic enamel paint of approved brand and manufacture to give an even shade : 1. Two or more coats on new work [Through Rate]
109	[11.91]Melamine polishing on wood work (one or more coat). [Through Rate]
110	[11.95.1]Finishing walls with Acrylic Smooth exterior paint of required shade : 1. New work (Two or more coat applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) [Through Rate]
111	[12.1.1.1]Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or dash fastener shall be paid separately). 1.1. Second class teak wood [Through Rate]
112	[12.12.1]Providing and Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1. 1.5 mm thick [Through Rate]
113	[12.136.4]Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape and size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) crescent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame and sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware`s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing and direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 4. Three track three panels sliding door with fly proof S.S wire mesh (Two Nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm up to 5.00 sqm) [Through Rate]
114	[12.157.1.2]Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : 1.2. For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) [Through Rate]
115	[12.157.1.3]Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : 1.3. For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) [Through Rate]
116	[12.157.2.2]Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : 2.2. For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) [Through Rate]
117	[12.158.2]Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. 2. Pre-laminated particle board with decorative lamination on both sides [Through Rate]
118	[12.159.2]Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 2. With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) [Through Rate]
119	[12.160.2]Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight up to 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. 2. With brass cover plate minimum 1.25 mm thickness [Through Rate]
120	[12.167.2]Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge 2. Powder coated minimum thickness 50 micron aluminium [Through Rate]
121	[12.169.1]Filling the gap in between aluminium frame and adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. 1. Up to 5mm depth and 5 mm width [Through Rate]
122	[12.172.2]Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F and ISO 11600 2. Up to 10 mm depth and 10 mm width [Through Rate]
123	[12.173]Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge. [Through Rate]
124	[12.177.1]Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 1. With toughened glass panes of 6 mm thickness (weight not less than 15 kg/sqm) [Through Rate]
125	[12.3.3.2.2]Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 3.2.2. Kiln seasoned and chemically treated Hollock wood 50x20 mm [Through Rate]
126	[12.36.1]Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 1. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws [Through Rate]
127	[12.78.1]Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 1. 250x10 mm [Through Rate]
128	[12.82]Providing and fixing bright finished brass night latch of approved quality including necessary screws etc. complete. [Through Rate]
129	[12.86]Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. [Through Rate]
130	[12.88]Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight up to 35 kg and door width up to 700 mm), with necessary accessories and screws etc. complete. [Through Rate]
131	[12.97.1]Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 1. 125x75x4 mm [Through Rate]
132	[13.21.2]Supply and fixing Windows frames (Chowkhats) including mullions consisting frame fabricated from sheet roll formed out of 1.2mm thick galvanized sheet as per IS:277 (Base steel as per IS 513) with zinc of 120 gm/sqm and Powder coated with pure Polyester powder up to 50 microns (as per approved colour), 3 Nos. 100mm butt - hinges 2mm thick, 6 Nos. 1.2mm thick CRCA electroplated stiffner, 6 Nos. M.S hold fast with split and tail welded to stiffner plate 200mm long, receiver for aldrop, weld less corner assembly with brackets and screws, M.S tie rod 50mm x 25mm to be fixed at bottom finished with powder coated total thickness of coating 0.6mm of approved shade, fixed in position including the cost of cement concrete for 1:2:4 for fixing lugs complete in all respects as per drawing, design, specification and entire satisfaction of Engineer-in-charge. 2. Door Frame of size 125mm x 60mm with 37mm wide double rebate for 35mm door shutter [Through Rate]
133	[20.36]Making connection with the existing G.I. branch main up to 40 mm size including cutting and threading pipe etc., complete excluding cost of tee and long screw, but including cartage of material to site. [Through Rate]
134	[20.71.2]Supply, erection, testing of Ceiling fans IS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer-in-charge 2. 56\\" (1400mm) [Through Rate]
135	[20.72]Supplying, errection, testing of Exhaust fan (as per IS code 374) having a capacity of 45 cubic metre per minute complete with suitable G.I sheet ducting in structure confirming to latest IS specifications complete in all respect to satisfaction of Engineer-in-charge. [Through Rate]
136	[21.38.11]`Lowering salt glazed stoneware pipes and specials into trenches for all depths and laying out the same to correct alignment gradient, level etc in trenches including all dressing and trimming of bed and sides of trenches, if required, trimming and cutting of concrete beds and joint holes, supporting the pipes and specials, in correct position in a suitable rigid manner while the same are being jointed and until the surrounding benching hunching and envelopes are completed. The sewer shall rest on the bed at every point throughout its length and to ensure this, it shall be grouted in without extra charge by the contractor with lime surkhi mortar, in the case of lime concrete beds and 1:3 cement sand mortar in the case of cement concrete beds including cartage from Divisional Store or nearest Railway station to site of work.The internal diameter of sewer being :-` 11. 450 mm internal diameter of sewer [Through Rate]
137	[21.93.1]Providing and fixing SFRC MANHOLE COVERS AND FRAMES MARKED WITH IS: 12592 including setting the same to correct lines and levels in 1:3 cement sand mortar over manhole including carriage loading unloading stacking handling re-handling etc. complete in all respects to the satisfaction to the Engineer-in-charge. 1. Type:- Extra Heavy Duty Set (EHD-35) 560MM Clear Opening [Through Rate]
138	[22.103.3]Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 3. 25 mm nominal bore [Through Rate]
139	[22.105.1]Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 1. 15 mm nominal bore [Through Rate]
140	[22.108.1]Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 1. 15mm nominal bore [Through Rate]
141	[22.14.2.2]Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 2.2. Flexible pipe 40 mm dia [Through Rate]
142	[22.16]Providing and fixing 40mm i/d G.I. waste pipe embedded in walls up to floor level including cost of union and plumber joint [Through Rate]
143	[22.181]Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. [Through Rate]
144	[22.222.2.2]Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. 2.2. Single Socket Type B 110mm o/d SWR UPVC pipe lines laid complete [Through Rate]
145	[22.222.2.3]Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. 2.3. Single Socket Type B 90mm o/d SWR UPVC pipe lines laid complete [Through Rate]
146	[22.23.1]Providing and fixing white vitreous chinaware pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 1. W.C. pan with ISI marked white solid plastic seat and lid [Through Rate]
147	[22.25.2]Providing and fixing white vitreous chinaware flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 2. One urinal basin with manually operated 5 litres PVC cistern and manually operated stop cock/ angle valve [Through Rate]
148	[22.88.3]Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 3. 25 mm dia nominal bore [Through Rate]
149	[22.89.1]Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 1. 15 mm dia nominal bore [Through Rate]
150	[22.89.2]Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 2. 20 mm dia nominal bore [Through Rate]
151	[22.92.1]Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 1. 25 to 40 mm nominal bore [Through Rate]
152	[22.94.1]Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 1. 15 mm nominal bore [Through Rate]
153	[22.94.2]Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 2. 20 mm nominal bore [Through Rate]
154	[22.94.3]Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 3. 25 mm nominal bore [Through Rate]
155	[22.98.1]Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 1. 25 mm nominal bore [Through Rate]
156	[22.98.2]Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 2. 20 mm nominal bore [Through Rate]
157	[23.21]Fixing of LED Down lighter 7 to 28 Watt on ceiling or in false ceiling , including cutting/making hole in ceiling including making connections etc as required [Through Rate]
158	[23.22.1.10]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.10. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 125 to 160 amp, 25 KA [Through Rate]
159	[23.22.1.9]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.9. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp , 25 KA [Through Rate]
160	[23.22.2.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 2.1. MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings MCCB up to 125 A FP [Through Rate]
161	[23.22.4.11]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.11. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. Vertical TPN DB Double Door 8 way ( 8 incoming 3phase*8 outgoing) [Through Rate]
162	[23.22.4.2]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.2. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 8 way ( 2 incoming and 6 outgoing) [Through Rate]
163	[23.22.4.3]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.3. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 12 way ( 2 incoming and 10 outgoing) [Through Rate]
164	[23.22.4.4]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.4. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 16 way ( 2 incoming and 14 outgoing) [Through Rate]
165	[23.22.4.5]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.5. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 4 way ( 8 incoming and 3phase*4 outgoing) [Through Rate]
166	[23.22.5.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole [Through Rate]
167	[23.22.5.3]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.3. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Double POLE [Through Rate]
168	[23.22.5.4]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.4. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. Double pole [Through Rate]
169	[23.22.5.6]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.6. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. MCBs TRIPLE POLE [Through Rate]
170	[23.22.5.7]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.7. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp MCBs FOUR POLE [Through Rate]
171	[23.22.5.8]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.8. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. MCBs FOUR POLE [Through Rate]
172	[23.22.8.2]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 8.2. SITC Four pole ON LOAD Manual change over switch in SS enclosure of following Ratings 100 amp 415 volts [Through Rate]
173	[23.22.8.3]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 8.3. SITC Four pole ON LOAD Manual change over switch in SS enclosure of following Ratings 200 amp 415 volts [Through Rate]
174	[23.23.1.3]MISCELLANEOUS 1.3. Supply and fixing Galvanised Iron flexible pipe complete with socket nipples and check nuts etc. at both ends (Up to length of one metre):- Size 25 mm dia [Through Rate]
175	[23.23.6.1]MISCELLANEOUS 6.1. Supply and erection of MS cable tray , duly pained as required including erection of the same on wall or ceiling with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. MS perforated cable tray painted with powder coating 100 X 50 X 2 mm [Through Rate]
176	[23.23.8.1]MISCELLANEOUS 8.1. Supply and laying of multicore telephone cable conductor size 0.51 mm bright annealed copper conductor PVC insulated and sealed in existing pipe/channel and making necessary connection complete in all respect up to the entire satisfaction of the Engineer-in charge of the work. 2 pair telephone wire [Through Rate]
177	[23.23.9]MISCELLANEOUS 9. Supplying and drawing of 1 no UTP 4 pair CAT 6 LAN Cable in the existing surface/recess MS/PVC conduit as required [Through Rate]
178	[23.24.3.3]MS STAND, BUS BAR CHAMBER AND PANELS 3.3. Supply and erection of metal clad bus bar chamber made from 1.6 mm thick M.S. sheet and fixing with rag bolts on wall or on existing pedestal/angle iron frame including bonding, detachable top and bottom including painting and necessary connection etc. (Aluminium bars). 100 amp 4 bars of 100 cm each (cross section 25 mm x 6 mm) chamber over all size 1.10 m x 45 cm x 18cm [Through Rate]
179	[23.27.5]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 5. M.S. pedestal of size 1200 mm wide ,1500 mm high ,450 mm deep and bottom totally open , duly embeded in cement concrete block of size 1350 mm x 600 mm x 200 mm above ground level , having a base of size 1500 mm x 750 mm x 250 mm below ground level . 0 0 [Through Rate]
180	[23.4.1.1]COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT (SURFACE/RECESS) 1.1. Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. Group A [Through Rate]
181	[23.4.2.1]COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT (SURFACE/RECESS) 2.1. Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. Group A [Through Rate]
182	[23.4.3.1]COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT (SURFACE/RECESS) 3.1. Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe, without separate control switch Group A [Through Rate]
183	[23.4.4.1]COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT (SURFACE/RECESS) 4.1. Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required Group A [Through Rate]
184	[23.4.5.1]COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT (SURFACE/RECESS) 5.1. Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required Group A [Through Rate]
185	[23.5.6.2]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.2. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 2.50 Sqmm(1.1.80mm) [Through Rate]
186	[23.5.6.3]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.3. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 4 Sqmm(1/2.24mm) [Through Rate]
187	[23.5.6.4]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.4. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 6 Sqmm(1/2.80mm) [Through Rate]
188	[23.5.6.5]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.5. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 10 Sqmm(1/3.50 mm) [Through Rate]
189	[23.8.1.6]FITTING AND ACCESSORIES 1.6. Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Call bell 220/230 volts musical type [Through Rate]
190	[23.8.10.1]FITTING AND ACCESSORIES 10.1. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 1 & 2 Modules including combined plate for Telephone and data [Through Rate]
191	[23.8.10.3]FITTING AND ACCESSORIES 10.3. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 4 Modules [Through Rate]
192	[23.8.10.6]FITTING AND ACCESSORIES 10.6. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 12 Modules [Through Rate]
193	[23.8.11.1]FITTING AND ACCESSORIES 11.1. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 1 way switch [Through Rate]
194	[23.8.11.11]FITTING AND ACCESSORIES 11.11. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. RJ 45 Computer DATA socket outlet for CAT 6 or CAT6e cable Modular type [Through Rate]
195	[23.8.11.3]FITTING AND ACCESSORIES 11.3. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp 1 way switch [Through Rate]
196	[23.8.11.4]FITTING AND ACCESSORIES 11.4. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp Socket [Through Rate]
197	[23.8.11.5]FITTING AND ACCESSORIES 11.5. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp 6 pin Socket [Through Rate]
198	[23.8.9]FITTING AND ACCESSORIES 9. Supply and erection direct reading LCD Display Digital Ammetre/Voltmetre ( without CT or PT ) on wall/existing penal complete in all respect with necessary connections [Through Rate]
199	[24.1.1]EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. [Through Rate]
200	[24.1.13]EARTHING AND LIGHTENING ARRESTOR 13. Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop earthing as required. [Through Rate]
201	[24.1.2]EARTHING AND LIGHTENING ARRESTOR 2. Extra for using salt and char coal/coke for pipe earth electrode as required. [Through Rate]
202	[24.11.18]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING AND ERECTION/LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR CABLE 0.75 METER BELOW GROUND LEVEL COVERED WITH SAND AND BRICKS INCLUDING EXCAVATION AND REFILLING OF TRENCHES 18. 10 Sq mm 4 core (Arm.) [Through Rate]
203	[24.11.24]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING AND ERECTION/LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR CABLE 0.75 METER BELOW GROUND LEVEL COVERED WITH SAND AND BRICKS INCLUDING EXCAVATION AND REFILLING OF TRENCHES 24. 16 Sq mm 4 core (Arm.) [Through Rate]
204	[24.11.32]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING AND ERECTION/LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR CABLE 0.75 METER BELOW GROUND LEVEL COVERED WITH SAND AND BRICKS INCLUDING EXCAVATION AND REFILLING OF TRENCHES 32. 25 Sq mm 4 core (Arm.) [Through Rate]
205	[24.11.40]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING AND ERECTION/LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR CABLE 0.75 METER BELOW GROUND LEVEL COVERED WITH SAND AND BRICKS INCLUDING EXCAVATION AND REFILLING OF TRENCHES 40. 35 Sq mm 4 core (Arm.) [Through Rate]
206	[24.12.48]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING AND ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR CABLE 0.75 METER BELOW GROUND LEVEL COVERED WITHOUT SAND AND BRICKS INCLUDING EXCAVATION AND REFILLING OF TRENCHES 48. 50 Sq mm 4 core (Arm.) [Through Rate]
207	[24.14.24]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE ONSURFACE/ EXISTING CABLE TRAY COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 24. 16 Sq mm 4 core (Arm.) [Through Rate]
208	[24.14.32]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE ONSURFACE/ EXISTING CABLE TRAY COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 32. 25 Sq mm 4 core (Arm.) [Through Rate]
209	[24.14.46]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE ONSURFACE/ EXISTING CABLE TRAY COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 46. 50 Sq mm 3.5core (Arm.) [Through Rate]
210	[24.2.2.2]LT CABLE 2.2. Laying of underground cable 0.75 metre below ground level covered with sand and bricks including excavation and refilling of trenches.:- 16 Sq mm to 35 sqmm 2 to 4 Core [Through Rate]
211	[24.4.1.2]STREET LIGHT 1.2. 3 metres long 50 mm dia pole duly embedded 0.6 m below ground level. 4.5metres long 50 mm dia pole duly embedded 0.75 m below ground level. [Through Rate]
212	[24.4.11.1]STREET LIGHT 11.1. Erection of MS/GI/Swaged ( excluding Octagonal ) metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.Above 2.5 metre and up to 4 metre [Through Rate]
213	[24.4.2.3]STREET LIGHT 2.3. Supply and erection of GI bracket made of 32 mm dia medium class GI pipe, having 15 deg angle from horizontal, suitable for fixing on top of Street Light pole 120 cm long, with 30 cm high suitable size pole cap [Through Rate]
214	[24.4.4.1]STREET LIGHT 4.1. Erection of street light fitting on the pole including the cost of petty material required (irrespective of height/length of bracket) At Pole up to the height of 4.5 metres [Through Rate]
215	[24.4.4.3]STREET LIGHT 4.3. Erection of street light fitting on the pole including the cost of petty material required (irrespective of height/length of bracket) At Pole above 7 metres but up to the height of 9 metres. [Through Rate]
216	[24.4.5]STREET LIGHT 5. Supply and erection of Single Phase weather proof M.S. box of size 20 cm x 15 cm x 10 cm with hinged cover made of 2 mm thick MS sheet, locking arrangements, housed in wall/fixed on pole , including the cost of 1 no 4 way 16 A Bakelite connector, 1 no. 6 amp SP MCB and 1 Nos. 16 amp. neutral links fixed on Bakelite sheet in the M.S. box including painting and necessary connections. [Through Rate]
217	[24.4.6]STREET LIGHT 6. Supply and erection of Three Phase weather proof M.S. box of size 30 cm x 20 cm x 15 cm with hinged cover made of 2 mm thick MS sheet, locking arrangements, housed in wall/fixed on pole , including the cost of 1 no 4 way 16 A Bakelite connector, 1 no. 16 amp TP MCB and 4 Nos. 16 amp. neutral links fixed on Bakelite sheet in the M.S. box and necessary connections. [Through Rate]
218	[24.4.7.2]STREET LIGHT 7.2. Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required. 40 mm dia [Through Rate]
219	[24.4.8.7]STREET LIGHT 8.7. Supply and erection of Hot Dip Galvanized octagonal pole of 3mm thickness, with base plate including cost of nut and bolts , earthing studs, Integral Cable termination arrangement 5 mm thick Bakelite base plate on suitable welded MS/GI bracket 32 A four way connector 2 no 10 A SP MCB , end cover and all accessories as supplied by the manufacture including Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 9 Metre Long pole with top dia 100 mm and bottom 200 mm with base plate of size 350 x 350 x 20 mm. [Through Rate]
220	[28.16]Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken up to 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately). For the purpose of measurement the entire treated surface will be measured. [Through Rate]
221	[28.39]Water proofing of roof terraces, Basements, Retaining Walls, Water tanks etc with Zydex Zycoprime / Elastobar / Equivalent solution so as to form a water-resistant cementitious bonding coat and to form on-site seamless cross-linked elastomeric membrane on the concrete surface to reduce its porosity. Creating a cementitious elastomeric polymeric membrane of 2 coats of Elastobar and Zycoprime/Equivalent after application of Zycosil and Zycoprime Solution in New Construction. Take equal parts of Elastobar and Cement and form a paste. Add little water to the paste to make it brush able. Apply the paste on surface with brush. Leave the surface for drying for at least 4 - 6 hours to get elastomeric membrane. After this application, make one more layer of rough cementitious membrane using mixture of 1 Part of Zycoprime plus 1 Part of Cement plus 1 Part of fine sand. Apply paste on the surface with a brush to make a rough texture. Now your surface is ready to bond well with tiles/screed. [Through Rate]
222	[30.17]Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge. [Through Rate]
223	[30.22]Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. [Through Rate]
224	[30.52.1]Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of malba/ debris/rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in-Charge. 1. For door/ window/ clerestory window [Through Rate]
225	[30.88.1]Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 1. For pipes 100 to 250 mm diameter [Through Rate]
226	[4.40.5]Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : 5. Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same. [Through Rate]
227	[5.25]Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. [Through Rate]
228	[5.29.1]Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 1. Of area 3 sq. metres and below [Through Rate]
229	[5.29.2]Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 2. Of area beyond 3 sq. metres [Through Rate]
230	[5.42]Dismantling cement conglomerate / terrazzo floors 25 mm to 50 mm manually/ by mechanical means and disposal of material within standard lead as per direction of Engineer- in-charge. [Through Rate]
231	[5.43.1]Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 1. For thickness of tiles 10 mm to 25 mm [Through Rate]
232	[5.43.2]Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 2. For thickness of tiles above 25 mm and up to 40 mm [Through Rate]
233	[5.45]Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. [Through Rate]
234	[6.16]Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). [Through Rate]
235	[6.34.6]Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect above plinth level Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. 6. Thermo-Mechanically Treated bars of grade Fe-500D or more. [Through Rate]
236	[7.22.1]Brick work with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : 1. Cement mortar 1:4 (1 cement : 4 coarse sand) [Through Rate]
237	[8.29]Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete. [Through Rate]
238	[9.33]Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm ( plus 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. [Through Rate]
239	[9.57.1]Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 1. 75 mm diameter [Through Rate]
240	[9.57.2]Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 2. 110 mm diameter [Through Rate]
241	[9.57.3]Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 3. 150 mm diameter [Through Rate]
242	[9.59.1]Providing and fixing Unplasticised -PVC pipe clips of approved design to Unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 1. 75 mm [Through Rate]
243	[9.59.2]Providing and fixing Unplasticised -PVC pipe clips of approved design to Unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 2. 110 mm [Through Rate]
244	[9.59.3]Providing and fixing Unplasticised -PVC pipe clips of approved design to Unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 3. 150 mm [Through Rate] Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents

Also Visit

Tenders

Haryana Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Renovation Of 5 No. Rooms (Room No. 01 To 05) With Electrical Installation Works, Furnishing Alongwith Up-Gradation Of Kitchen At Pehowa Tourist Complex, Kurukshetra., Pehowa-Haryana

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Renovation Of 5 No. Rooms (Room No. 01 To 05) With Electrical Installation Works, Furnishing Alongwith Up-Gradation Of Kitchen At Pehowa Tourist Complex, Kurukshetra., Pehowa-Haryana

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us