|
| 1 | Dismantling Asbestos cement (corrugated, semicorrugated, etc.), sheet in roof coverings including Naintal or similar pattern roof covering complete all as specified and directed. |
| 2 | M&L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa, as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 3 | M&L Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa, as in ridges, roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 4 | Excavation in post hole each, not exc. 0.50 cum, getting out hard/ dense soil as, returning filling, in ramming earth or broken rubble mixed with earth around in layers not exc. 25 cm, watering and removing surplus soil, complete all as specified and directed. |
| 5 | M&L for cement concrete type D-2 1:4:8 using 40mm graded stone aggregate) in foundation filling, bed blocks the mass concrete complete all as specified and directed. |
| 6 | M&L Poly carbonat sheet (Transparent) plain corrugated sheeting 10mm thick as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 7 | S&F Steel work in tubular trusses, including special shaped washer etc. as in posts, main and cross beam, hip and jack rafters, purlins, where connected to common rafters (beam, tee, channel pipes tubes and flat sections etc) including distances pieces, cleats etc. cutting half brick thick wall and fixing with cement mortar of grade FE-410, (gde-E-250) quality complete all as specified and directed. |
| 8 | S&F Rolled sections as in posts, main and cross beam, hip and jack rafters, purlins, where connected to common rafters (beam, tee, angle, channel pipes, tubes, plates and flat sections etc) including distances pieces, cleats etc. cutting half brick thick wall and fixing with cement mortar of grade FE-410, (gde-E-250) quality complete all as specified and directed. |
| 9 | S&F MS plates (plain or chequred) channel square cut to or notched forming hole with riveted bolted welded attachment for Fe-410W complete all as specified and directed. |
| 10 | S&F Mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, earth screwed end to be fitted with washers and one hexagonal or square nut, length of bolt etc 22.5 cm & n.exc 30 cm long dia of shank 16 to 20mm complete all as specified and directed. |
| 11 | M&L for preparation of new steel surfaces of any description, over 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, comlete, complete all as specified and directed. |
| 12 | S&F ventilator fans for sheds specialize high powered or passive device designed to expel hot, humid and stale air while drawing in fresh air to regulate temperature, reduce moisture and improve air quality, essential for proteching equipment from dust, rust, managing dust and reducing odors, installed on wall or roofs complete all as specified and directed. |
| 13 | S & F 110mm bore PVC (SWR) pipes single socket in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 14 | S & F 110mm bore PVC (SWR) bend any radius including all fitting complete all as specified and directed. |
| 15 | S & F 150mm bore PVC (SWR) half gutter pipes single socket in any length with rubber ring joints including all fitting complete all as specified and directed. |
| 16 | Taking down cement plaster on wall built in cement mortar including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 17 | M&L for rendering 15mm thick on fair faces of concrete/ brick interior surfaces in cement mortar 1:6 finished fair and even without using extra cement at any height of bldg complete all as specified and directed. |
| 18 | M&L for preparation of new wall surfaces & applying birla/ JK wall care white putty 2mm thick for levelling in surfaces and applying two coat of interior emulsion distemper over a coat of wall primer including preparation of surfaces of wall etc. at any height of bldg complete all as specified and directed. |
| 19 | M&L for rendering 15mm thick on fair faces of concrete/ brick exterior surfaces in cement mortar 1:4 finished fair and even without using extra cement at any height of bldg complete all as specified and directed. |
| 20 | M&L for preparation of new surfaces and applying two coat of 100% Premium Acrylic emulsion paint having VOC less than 50 gm/ litrs and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over applying and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over new surfaces at any height of bldg complete all as specified and directed. |
| 21 | Demolition of brick work of stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 22 | M&L for brick work with modular size kiln well burnt sub-class 'B' bricks, strength or curved on plan exceeding 6 m in mean radius built in CM (1:4) complete all as specified and directed. |
| 23 | M&L for Fromwork to sides and soffits of lintel/ lintel band for flat and rough finished surface of concrete complete all as specified and directed. |
| 24 | M&L for RCC Nominal mix type A1 1:1.5:3 (using 20mm graded aggregate) as in lintels, roof, beams, bands including necessary from work complete all as specified and directed. |
| 25 | M&L for Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. |
| 26 | M&L for Mild steel TMT bars 6mm dia to 10mm dia length, bent to shape as required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. |
| 27 | Demolition of stone slabs of any description or thickness in floors/ walls laid bedded and pointed in any mortar etc. complete removal of debris outside MD land complete all as specified and directed. |
| 28 | M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing including 15mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 29 | All as per Srl item No. 28.00 above but, on vetical surface such as skirting including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed |
| 30 | M&L for cement concrete type C-1, 1:3:6 using 20mm graded stone aggregate as in copping etc. including necessary fromwork complete all as specified and directed. |
| 31 | M&L for PCC 75mm thick type B-2 (1:2:4) (using 40mm graded stone aggregate) in plinth protection, joints should be filled with bitumen primer etc. complete all as specified and directed. |
| 32 | S&F 4mm thick wire mesh welded or woven into square, rectangular opening. Renowned for high strength, corrosion resistance and duribility used for heavy duty applications like security fencing, machine guards, construction reinforcements and industrial cages complete all as specified and directed. |
| 33 | Providing precast cement concrete louvres and jallies, 35mm thick type B0 1:2:4 (using 12.5mm graded stone aggregate) set in cement mortar (1:4) mea-sured solid) including all mouldings but excluding frame complete all as specified and directed. |
| 34 | S & F of Powder coated aluminum three track sliding shutters two Glazed shutters and one guazed shutters (with wire mesh), each shutter width one half of the length of window with the following specifications and making good the adjacent surfaces.(i) Three way track for sliding shutters of cross section 91.80mm x 31.75mm x 1.50mm thick.(ii) Sliding shutter frame of cross section 40 x 18 x 1.30mm.(iii) Aluminium glazing strip of size 18.2 x 16.66mm.(iv) 4 to 5mm thick float glass superior quality make Modi float for two shutters.(v) IDPE rubber gasket for fixing glass.(vi) Locking cleat per shutter - 01 No.(vii) Two Nos sliding rollers per shutter.(viii) Rubber shock absorber 03 No per shutter.(ix) Aluminium wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm for one shutter.(x) Fixing screws for frame with wall - 06 No per window. |
| 35 | Dismantling/ wall and ceiling boards (fibre pulp, insulation etc) or insulation boards/ slabs |
| 36 | Providing and fixing in true horizontal level 600mm x 600mm, false ceiling system hot dipped galvanised steel section, exposed surface with pre-coated capping, main tee of size 24 x 38mm, having 0.25mm gauge at every 1200mm centre to centre maximum and rotary stitched cross tee of size 24 x 38mm having 0.25mm gauge at every 600mm c/c and sub cross tee of size 24 x 38mm, having 0.25mm gauge at 1200mm c/c and wall angle of size 19 x 19mm, having 0.35mm gauge fixed to the periphery of the wall. The abovegrid is suspended at every 1200mm c/c in both directions using 3.0mm thick pre-straightened GI wire. laying 595 x 595 x 6mm thick E-Board Designer ceiling fixing 600mm x 60mm x 6mm grid (Frame work) etc complete all as specified and directed. Please Enable Macros to View BoQ information |
