|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) in foundation trenches or drains (not exceeding1.5m in width or 10sqm on plan), including dressing of sides and ramming of bottoms, lift upto1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed,within a lead of 50 m. |
| 2 | Dry stone pitching (any thickness) excluding cost of stones. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level. PCC 1:4:8 (1 cement: 3 coarse sand: 8 graded stone aggregate 20mm nominal size) : |
| 4 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12(1cement :6coarsesand:12graded stone aggregate 20 mm nominal size) upto plinth level with :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 5 | Dry random rubble masonry with hard stone in foundation and plinth: Using quarry stone without bond stone |
| 6 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts ans sturts, etc. upto floor five level excluding cost of centring, shuttering, fmishing and reinforcement. RCC 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20mm nominal size) : |
| 7 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 8 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm indepth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m |
| 9 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 10 | Providing & fixing upto floor five level compressed stabilized earth blocks (CEB) made an appropriate mix of dry inorganic subsoil, non-expansive clay, sand, and aggregate with 5% cement as stabilizer, in mud mortar, including cost of materials complete. |
| 11 | Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete :1:3:6 (1 Cement: 3 coarse sand 6 graded stone aggregate 20mm nominal size |
| 12 | Thermal Insulation of roofing and walls with Expanded polystyrene fixed with suitable adhesive to the false ceiling as per the directions of the Engineer-in-charge:With Type N - Normal 50 mm thick |
| 13 | Centring and shuttering including strutting, propping etc. and removal of form for:- Foundations, footings, bases of columns, etc. for mass concrete |
| 14 | For Columns, Pillars, Piers, Abutments, Posts and Struts |
| 15 | For· Lintels, beams, plinth beams, girders, bressumers and centilevers. |
| 16 | For· suspended floors, roofs, landings, balconies and access platform. |
| 17 | Edge of Slabs and breaks in floors and walls. |
| 18 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class kail wood: |
| 19 | Providing and fixing ISI marked flush door shutters conforming to IS:2202 (PartI) decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:9.21.1 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 20 | Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : size : 300x16 mm |
| 21 | Providing and fixing ISI Marked oxidised MS tower bolts (barrel type) withnecessary screws etc. complete. : 200x10 mm : |
| 22 | Providing and fixing ISI Marked oxidised MS handles with screws etc. complete :125mm |
| 23 | Supply, Installation, Testing and Commissioning of uPVC mahogony or any approved shade casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.50 ± 0.2 mm thick steel with Zinc Al coating made from roll forming process of required length (shape & size according to uPVC profile), uPVC co-extruded extruded glazing beads of appropriate dimension, stainless steel (SS 304 grade) friction hinges of 2.5mm plate thickness, zinc alloy (white powder coated) casement handles of same brand as window supplier, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary coated steel screws etc. The profiles should be mitre-cut and seamlessly Zip-welded without needing corner cleaning. Both the shutter and bead profiles should have co-extruded gaskets in the glazing area. The frame and shutters should have EPDM gaskets in the sealing area. Mullion (if required) shall be fixed through Mechanical joint including drilling of holes for fixing hardware's and drainage of water etc. The vertical member should not deflect more than L/175 or 19mm for SGU and L/175 or 15mm for DGU, whichever is the least for a wind load of 1.5kPa.After fixing frame the gap between frame and adjacent finished wall shall be filled weatherproof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note: For uPVC frame, sash and stay should open to allow cleaning of glass outside surface. Multipoint locking to be provided with espags of SS304 grade. All shims to be capable of transferring the load evenly and made of a suitable material (Teflon, Nylon etc) capable of lasting the life span of the system. All miscellaneous items such as peripheral sealants, backer rods, fasteners etc to be included in the rate. (Makes: Rehau uPVC, Saint-Gobain uPVC, Schaech uPVC or approved)Casement window single panel with S.S. friction hinges (16.5mm stack height) made of 44x70mm depth frame and 80x70mm depth shutter having wall thickness of 2.3 ± 0.2 mm and glazing bead of appropriate dimension. DGU unit of combination 6mm toughened glass+12mm thick air gap+6mm thick clear toughened glass. Outer 6mm glass pane will have special energy saving Magnetron coating on clear glass base on the air gap face to achieve a U-value of 1.5 W/m2-K (Area of window above 0.75 sqm.) and a visible light transmission factor of 70 to 80%.,slider if needed (Makes: Rehau uPVC, Saint-Gobain uPVC, Schueco uPVC, Finesta uPVC) including double glass completed |
| 24 | Providing and fixing factory made uPVC colour casement/casement cum fixed glazed windows with toughned glass comprising of uPVC multi chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powdercoated)casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plasticcaps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wallshall be filled with weather proof silicon sealant over backer rod of required size and of approved quality,all complete as per approved drawing & direction of Engineer-in-Charge.) Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth& width of profile shall be acceptable.uPVC profile should be tested by BSI(UK) & SKZ(Germany) @25000 weathering hours.Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made of (big series) frame 67 x 60 mm , sash 67 x80 mm &mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing of appropriate dimension with toughened glass complete job . |
| 25 | 12mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 4 ( 1 cement : 4 coarse sand) :Inside wall :- |
| 26 | 6mm cement plaster to ceiling of mix 1:3 (1 cement : 3 fine sand)Ceiling |
| 27 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1mm thick.Qty vide item i.e On (6mm cem plaster on Ceiling & 15mm Plaster on inner walls) |
| 28 | Distempering with 1st quality acrylic distemper (ready mixed) having VOCcontent less than 50 gms/litre, of approved manufacturer, of required shade andcolour complete, as per manufacturer's specificationTwo or more coats on new work |
| 29 | Rough cast plaster up-to 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. Outside wall |
| 30 | EXTERIOR FINISHING Finishing walls with water proofing cement paint of required shade: new work (two or more coat applied. @ 3.84 kg/10sqm.) Qty vide item 28 ( Rough Cast) : |
| 31 | Providing wood work in frames of false ceiling, partitions etc. sawn an fixed in position with necessary stainless steel screws etc.Budloo |
| 32 | Providing and fixing Ply wood 5 ply with commercial ply on both faces 6 mm thick |
| 33 | Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge complete with; Budloo wood |
| 34 | Providing and fixing wooden moulded corner beading of triangular shape to the junction of panneling etc. with iron screws, plugs and priming coat on unexposed surface etc. completeSecond class Kail wood - 50x50mm (base & height) |
| 35 | French Spirit polishing, two more coats on new works including coat of wood filler. |
| 36 | Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand), complete job. |
| 37 | Providing and fixing 12mm prelaminated flooring of approved Brand as per direction of Engineer at Site , complete job. |
| 38 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622(thickness to be specified by the manufacturer), of approved make, in all colours, shadesexcept burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 39 | Providing and laying ceramic glazed floor tiles 300x300 mm (thicknessto be specified by the manufacturers) of 1st quality conforming to IS:15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4( 1 cement : 4 coarse sand) including pointing the joints with whitecement and matching pigment etc., complete.In colour such as White, Ivory, Grey, Fume Red Brown |
| 40 | Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded andpre polished machine cut granite stone of required size and shape of approvedshade, colour and texture in footpath, flooring cut granite stone of required sizeand shape of approved shade, colour and texture in footpath, flooring in roadside plazas and similar locations, laid over 20mm thick base of cement mortar 1:4(1cement : 5 coarse sand) including grouting the joints with white cement mixedwith matching pigment, epoxy touch ups etc. complete as per direction ofEngineer-in-Charge. With granite stone of area less than 0.50 sqm. |
| 41 | Structural steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded |
| 42 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sitex, Electroplast, Star, Lotus or equivalent having valid lSI license. - Including puffing of tank and insulating of outlet up-to 15 meters. Complete job. |
| 43 | Providing and fixing of material for the insulation of Water storage Tank with nitrile sheet, taping with cello tape, rockwool 6 inch per side, wire mesh, polythene, aluminium sheet 26 guaage cladding with dia of, complete job, 19mm thick nitrile sheet. |
| 44 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink without drain board 610x510 mm bowl depth 200 mm. |
| 45 | Supplying and fixing of following electrical items suitable for operating on 240 /230 volts AC, 50 HZ supply , including connection etc. as required. Exhaust fan 300 mm size (Heavy duty) CG transair or equivalent approved make |
| 46 | Providing and fixing water closet squatting pan ( Indian type W.C. pan) with 100 mm sand cast Iron P or Strap, 10 litre low level P.V. C. flushing cistern including flush pipe (of approved make) \\"manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. Orissa pattern white vitreous china W.C. pan of size 580x440 mm with integral type foot rests. |
| 47 | Providing and fixing CP Jali of approved make. |
| 48 | Providing and fixing wash basin with C. I./M.S. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets cutting and making good the walls wherever require :, White Vitreous China wash basin size 630x450 mm with single 15 mm C.P. brass pillar taps |
| 49 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 50 | Providing and fixing brass bib cock of approved quality.20 mm nominal bore |
| 51 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (both shower & Tap control).(a) 15 mm nominal dia |
| 52 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 15 mm nominal bore |
| 53 | Providing and fixing C.P. brass close hole basin mixer piller tap of approved quality and make, weighing not less than 1.970 kg.15 mm nominal bore of standard back type |
| 54 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 150 mm diameter |
| 55 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete : Flexible pipe 32mm |
| 56 | Providing and fixing un-plasticized PVC connection pipe with brass unions. 45 cm length 20 mm nominal bore |
| 57 | Providing and fixing CP brass toilet paper holder having (ISI marked) |
| 58 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms. |
| 59 | Providing and fixing 600mm long towel rail with total length of 645mm width, 78mm wide and effective height of 88mm weighing not less than 190gms (ISI marked) |
| 60 | Providing and fixing mirror of superior glass (of approved quality) and of requiredshape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backingCircular shape 450mm dia. |
| 61 | Providing and fixing PVC soil, waste and vent pipe 10 FT long: 75 mm dia complete job. (a) 75mm dia. Or 3\\" |
| 62 | PVC soil, waste pipe and vent pipe 10FT long: (b)100 mm dia |
| 63 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SOR 7.4 UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings 1/C fixing the pipe with clamps at 1.00m spacing. This includes cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-charge. (concealed work incl. cutting chases and making good the walls etc.(a) Pn-16 pipe, 40mm 0D 1.5\\" |
| 64 | (b) Pn-16 pipe, 25mm 0D 1\\" |
| 65 | Providing and fixing insulation work on PPR pipe by using nitrile tube taping with cello tape, Rock wool 6inch, wire mesh, polythene, taping with cello tape, aluminium sheet 26 guage cladding with dia complete job including carriage 40mm (External pipe) |
| 66 | Providing and fixing insulation work on PPR pipe by using thermocol flex/K flex and taping over pipe complete job 25mm (Internal pipe) |
| 67 | Providing and fixing heat tape 33watts made of denforced or chromolex or eq. make as approved, complete job |
| 68 | Providing and fixing Thermostat Automatic Timer all complete job |
| 69 | Providing and fixing ball valve (brass) of approved quality complete : High or low pressure with plastic floats:25 mm nominal bore |
| 70 | Providing and fixing square-mouth S.W. gully trap grade ‘A” complete with C.I.grating brick masonry chamber with water tight C.I. cover with frame of 300x300mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :with Sewer bricks conforming to IS : 4888 |
| 71 | Providing and fixing water heating geyser of capacity 25 liter of approved make. |
| 72 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design. In 75x75 mm deep chase. Qty vide parapet:- |
| 73 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)- |
| 74 | Providing and fixing of wooden rail asthetic corres as per recommended by engineer incharge inl. Cost of required nails, adhesives and carriages complete jobs |
| 75 | Providing and fixing of readymade wooden balusters, port, Newel, main Balusters for rail of design recommended by engineer incharge with screw base for support inl. Cost of required nails, adhesives and carriages complete jobs |
| 76 | Renewing glass panes, with putty and nails wherever necessary including rackingout the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)Add cost for Roof Treatment component (make such as Dr. Fixit) |
| 77 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.All kinds of soil |
| 78 | Disposal of earth --- 1km: |
| 79 | Carriage of material from source to site of work by MT.Including loading, unloading and stacking complete. Cement and steel avg. lead ….....................158 KM |
| 80 | Sand avg. lead….........................7 KM |
| 81 | Stone aggregate avg. lead ….....................29 KM |
| 82 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. |
| 83 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 84 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required2 x 1.5 Sq.mm + 1 x 2.5 Sq.mm earth wire |
| 85 | 2 x 2.5 Sq.mm + 1 x 2.5 Sq.mm earth wire |
| 86 | 2 x 10 Sq.mm + 1 x 6 Sq.mm earth wire |
| 87 | 4 x 10Sq.mm + 2 x 6 Sq.mm earth wire |
| 88 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required for inverter.1x 1.5 sq.mm |
| 89 | 1 x 2.5 Sq.mm |
| 90 | Supplying and fixing following modular type switch/socket on the existing switch box cover including connections etc. as required.5/6 A switch |
| 91 | 3 pin 5/6 A socket outlet |
| 92 | 15/16 A switch |
| 93 | 6 pin 15/16 A socket outlet |
| 94 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 95 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 96 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2nos. 3 pin 5/6 amps modular socket outlet and 2nos 5/6 amps modular switch, connection etc. as required |
| 97 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 amps & 15/16 amps. modular socket outlet and 15/16 amps modular switch connection etc. as required. |
| 98 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) :-8 way ( 4+24) Double Door |
| 99 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.single pole 6/16 amp. |
| 100 | Supply and fixing of following sizes of PVC conduit alongwith accessories in surface/recessed including cutting the wall and making good the same in case of recessed conduit as required. 25 mm |
| 101 | Supply, installation, testing & commissioning of GI Electrode Earthing with 84mm dia GI pipe ISI marked and 3 meter length, with 40mm x 5mm thick electrode, the electrode should be hot-dip galvinised. The GI Electrode shall be pre-filled with Cristaline Conductive Materila (CCM). The GI electrode shall be surrounded with BEE MOIST compound to provide maximum contact betwen the electrode and compound should be eco-friendly GI Electrode Earthing should be maintinance free and does not require regular manual addition of water . The earthing pit should be covered with PVC cover. |
| 102 | Supplying and laying 25mm x 5mm G.I strip at 0.50 metre below ground as strip earth electrode including connection/terminating with G.I nut, bolt, spring, washer etc. as required. ( Jointing shall be done by overlapping and with 2 sets of G.I nut bolt & spring washer spaced at 50mm). |
| 103 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 104 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.MCCB FP 100 Amp 30KA |
| 105 | Onload Change over Switch 100Amp MCCB Type FP |
| 106 | Fabrication ,supplying ,installation testing and commisssioning of following pannel made out of 2mm thick M.S sheet, floor mounted ,vermin & dust proof ,indoor type with lockable type hinged doors,duly painted with provision for fixing of 1 no incomer MCCB,MCCB type change over switch -1 No including supply and fixing 2 set of Aluminium Bus bar ,and strip for housing MCB,s 24 Nos , MF Digital Meter and and other allied accessories as required . |
| 107 | Supplying and fixing of following rating 240/415 Volt's \\"C\\" Series miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning (Above to 32 Amp.).SPN 63 Amp |
| 108 | TPN 63 Amp |
| 109 | Supply and fixing of 1.1 KV PVC insuated and PVC sheathed XLPE power cable of following sizes on surface/surface cable tray/0.50 m below ground level etc as required including carriage upto site of work.(Make as per annexure enclosed)3.5 core 50 sqmm armoured. |
| 110 | 20 watt LED tube light fitting. LL20-221-XXX-65NE3 of wipro or equivalent make and model Philips/Crompton Greaves. |
| 111 | Supply and fixing LED type Down Lighter of following ratings 12 watt |
| 112 | Supplying and fixing bulk head fitting along with 9 watt LED lamp |
| 113 | Supplying and fixing of 120 watt LED Street Light complete with GI pipe bracket duly embeded along the parapet /wall. Wipro LR02-132-XXX-57-G2 or equivalent approved make Please Enable Macros to View BoQ information |
