|
| 1 | SITC of 2-way full range all weather Line Array Loudspeaker,Having line Array Stackable Cabinet L.F, 1 x 14” or hIGHER 1 x 1.4” or higher Horn loaded Compression Driver,750 watt or lower Continous RMS Power,2000W or Higher Peak Power, 8 ohms, Frequency Response(-10db) 55Hz or Lower and 18khz or Higher, Average Sensitivity - 98dB or higher, Max SPL Peak 135 db or higher, Horizontal Dispersion 60° or higher,Vertical Dispersion 25° or Higher,The Speaker cabinet Should be of IP 55 or higher Rated ,Powder-coated aluminum or Stainless Steel grille,UV-resistant and should have all Corrosion-resistant Components.Complete in all respects as approved and desired by the Engineer in-charge at site. |
| 2 | SITC of Powder coated Mild Steel Line array hanging Bracket KIT. Complete in all respects as approved and desired by the Engineer in-charge at site. |
| 3 | SITC of Professional Grade Four channel or Higher Power amplifier Having Power 4 x1200W @ 8 ohms at Each Channel or Higher, 4 x 1200W @ 4 ohms or higher Each Channel or Higher, Frequency Responce - 20Hz - 20kHz, , Input Impedence - 20k ohm , Crosstalk - >65dB or Higher, S/ N ratio - >101dB or Higher, Damping Factor - 800, THD - < 0.1% or Lower.Complete in all respects as approved and desired by the Engineer in-charge at site. |
| 4 | SITC of Digital signal processor Having 16 inputs or higher(atleast 8 Analog inputs + 8 Digital Inputs) , 16 outputs or Higher (Atleast 8 Analog outputs + 8 Digital outputs), Should Have Matrix DSP routing for all inputs and outputs,Should have Dante connectivity for Inputs and Outputs ,Should Have 32bit or higher floating point processor,24bit/48KHz or Higher sampling rate,In-built USB sound card for USB recording and soft video Conferencing Codec,Acoustic Echo Cancellation (AEC) 8x8 or higher Low pass & high pass filters and limiter on output channels,8-way GPIO (General purpose input output) configured as inputs or outputs, allowing for flexible control of digital signals,Ethernet, RS232/485 control interface for third-party control, Frequency Response 20Hz - 20kHz, ±0.3dB,Input Dynamic Range 110dB or higher,Output Dynamic Range 112dB or higher,,Input Impedance 5kΩ or higher Output Impedance 100Ωor higherComplete in all respects as approved and desired by the Engineer in-charge at site. |
| 5 | SITC of Handheld Microphone system having UHF Wireless Cardioid dynamic handheld microphone system with Frequency Response of 100 Hz or lower to 15 kHz or higher (+1 dB, -3 dB) , 60 dBA or higher S/N ratio, Total Harmonic Distortion <1.0% or lower (at 1 kHz, ±20 kHz deviation) , Dynamic Range 110dB or higher , Should have on/off switch, and have operating range 100 mtrs or higher , Multiple band with 10 or higher channels on each band ; maximum Output level XLR / Balanced: +9 dBV or higher & 6.3 mm (¼\\"\\") / Unbalanced: +4 dBV or highercomplete in all respects as approved and desired by the Engineer in-charge at site. |
| 6 | SITC of Hypercardioid dynamic Neodymium handheld Instrument microphone -HAVING Frequency Response Form 60 Hz or Lower to 14,000 Hz or higher , Open Circuit Sensitivity -54 dB or lower (1.9 mV) re 1V at 1 Pa or better Impedance-600 ohms or better , Should have on/off switch Integral 3-pin gold-plated XLRM-type connector , Rugged all-metal construction , complete with stand clamp and threaded adaptor and Foam Wind Screencomplete in all respects as approved and desired by the Engineer in-charge at site. |
| 7 | SITC of Gooseneck microphone having 5 pin Desk stand with RGB LED Ring,Logic switch Control,Polar Pattern Cardioids Condenser,Gooseneck Length 18\\" or higher ,Frequency Response From 50or lower to17000 Hz or higher,Open Circuit Sensitivity,Maximum Input Sound Level 121 dB or higher SPL,Dynamic Range 93 dB or higher ,Signal-to-Noise Ratio 66 dB or higher ,Impedance : 100 Ohms or higher ,Output Connector Integral 5-pin XLRM-typeLogic I/O capability permits control of remote devices from the power module’s touch-sensitive capacitive-type user switch RFI shielding.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 8 | SITC of POWER SEQUENCER ,MCU controlled smart power management system, TFT LCD screen withvoltage + status indicators, 10 channels or higher, controllable power output sockets, with each channel programmable delay on/off time, max 16A output per socket & 60A max total output, Smart over and undervoltage management with cut off, relay on/off with delay timer, RS232/485, network control interface availablecomplete in all respects as approved and desired by the Engineer in-charge at site. |
| 9 | SITC of FEEDBACK SUPPRESSOR HAVING 2 or more balanced inputs and 2 or more balanced outputs, should have 48V phantom power for MIC1/MIC2 with independant gain adjustment, rear panel AFS on/off switch, 48KHz samplfing DSP-based feedback suppressor engineered to eliminate acoustic feedback while maintaining natural sound clarity.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 10 | SITC of 16 or higher Channel Mixing Console having 10 or higher Mic inputs , 16 or higher Line Inputs, 4 or higher GROUP Buses , 1 or higher Stereo Bus , 4 or higher AUX.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 11 | SITC of Pure Copper Speaker Cable having 2 or Higher cores, Should have 4.0 Sq mm or higher thichness of each core with proper shielding and insulation.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 12 | SITC of Pure Copper Microphone Cable having 2 or more cores, shouled be sheilded type, and have 20/22 AWG thichness of each core.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 13 | SITC of Customized Mettalic Floor Box with 8 x XLR with standard accessories as required.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 14 | SITC of Powder Coated Mettalic AV Equipment Rack having size 42U Equipment rack to house all rack mountable equipment, with internal wiring, front glass access door,Ventilated Fans,Power Distribution Unit.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 15 | SITC of Various Bulk Connectors, Velco Tap, Cable ties, Audio Connectors such as XLR, Speakon, RCA, Phono and AUX etx, Audio Patch Cable etc as required.Complete in all respects as approved and desired by the Engineer in-charge at site. Please Enable Macros to View BoQ information |
