|
| 1 | SITC of 2-way full range Loudspeaker,Having Point Source Cabinet, should have 1 x 12” Low Frequency Driver, 1 x 1.4” or Higher Horn loaded Compression Driver, HF Horn or cabinate should Be Rotatble for getting desired coverage pattern ,400 watt or lower Continous RMS Power, 1400W or Higher Peak Power, 8 ohms impedence , Frequency Response(-3db) from 60Hz or lower to 18khz or higher, Average Sensitivity - 97dB or higher, Max SPL Peak 128 db or higher, Horizontal Dispersion 90° or higher,Vertical Dispersion 55° or Higher,The Speaker cabinet Should be made of Touring grade Birch Plywood and Have 12 or Higher x Suspension Mounting points for both horizontal and vertical flying Cabinet.Cabinet Should be Multi purpose cabinet design for FOH or monitor use. complete in all respects as approved and desired by the Engineer in-charge at site. |
| 2 | SITC of Customised Brackets made up of power coated Mild steel for mountind of speakers on wall horizontaly or vertically.complete in all respects as approved and desired by the Engineer in-charge at site..complete in all respects as approved and desired by the Engineer in-charge at site. |
| 3 | SITC of 2-way full range Loudspeaker,Having Point Source Cabinet, 1 x 8” Low Frequency Driver, 1 x 1.4” or Higher Horn loaded Compression Driver,Horn or cabinate should Be Rotatble for getting desired coverage pattern ,350watt or lowerContinous RMS Power, 400W or Higher Peak Power, 8 ohms impedence, Frequency Response(-3db) from 75Hz or lower to 17khz or higher, Average Sensitivity - 94dB or higher, Max SPL Peak 121 db or higher, Horizontal Dispersion 90° or higher,Vertical Dispersion 55° or Higher,The Speaker cabinet Should be made of Touring grade Birch Plywood,12 x Suspension Mounting points for both horizontal and vertical flying Cabinet.Cabinet Should be Multi purpose cabinet design for FOH or monitor use. complete in all respects as approved and desired by the Engineer in-charge at site. |
| 4 | SITC of Customised Brackets made up of power coated Mild steel for mountind of speakers on wall horizontaly or vertically. complete in all respects as approved and desired by the Engineer in-charge at site. |
| 5 | SITC of 2-way full range Looudspeaker,Having Point Source Cabinet, 1 x 8” Low Frequency Driver, 1 x 1” or Higher Compression Driver,200watt or lower Continous RMS Power,240W or Higher Peak Power, 8 ohms impedence or 70/100 volt line operation , Frequency Response(-10db) from 70Hz or lower to 20khz or higher , Average Sensitivity - 93dB or higher, Max SPL Peak 121 db or higher, Horizontal Dispersion 90° or higher,Vertical Dispersion 60° or Higher,includes an integrated transformer with multiple power tap settings,Speaker Should Have 80 watt or Higher power Taping at 100V operation,The Speaker cabinet Should be of IP 54 or higher Rated ,Powder-coated aluminum grille,UV-resistant ,Corrosion-resistant Components.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 6 | SITC of Professional Grade Four channel or Higher, Power amplifier Having Power output 600W or higher @ 8 ohms at Each Channel, 600W or higher @ 4 ohms at Each Channel in all channel drive mode, Frequency Responce - 20Hz - 20kHz, , Input Impedence - 20k ohm or higher, Crosstalk - >65dB or Higher, S/ N ratio - > 101dB or Higher, , THD - < 0.1% or Lower.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 7 | SITC of High performance Outdoor full range loudspeaker with 1 × 4.5”or higher Driver,Power Handling : 160 W or lower RMS ,200W or Higher peak,8 ohm and 100V/70V operation possible, LMT in-built,Frequency Response (-10dB) from 80Hz or Lower to 15KHz or higher,Average Sensitivity 85dB or higher,Calculated Max SPL 105dB Peak or Higher,Speaker Should Have 30 watt or higher Taping at 100V/70V operaion,Speaker Should Have Weatherised IP55 or higher Standard Cabinet. Speaker Should be floor mounted.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 8 | SITC of Digital signal processor Having 16 inputs or higher(atleast 8 Analog inputs + 8 Digital Inputs) , 16 outputs or Higher (Atleast 8 Analog outputs + 8 Digital outputs), Should Have Matrix DSP routing for all inputs and outputs,Should have Dante connectivity for Inputs and Outputs ,Should Have 32-bit or higher floating point processor,24bit/48KHz or Higher sampling rate,In-built USB sound card for USB recording and soft video Conferencing Codec,Acoustic Echo Cancellation (AEC) 8×8 or higher.Low pass & high pass filters – and limiter on output channels,8-way GPIO (General purpose input output) configured as inputs or outputs, allowing for flexible control of digital signals,Ethernet, RS232/485 control interface for third-party control, Frequency Response 20Hz - 20kHz, ±0.3dB,Input Dynamic Range 110dB or higher,Output Dynamic Range 112dB or higher,,Input Impedance 5kΩ or higher ,Output Impedance 100Ω or higher. complete in all respects as approved and desired by the Engineer in-charge at site. |
| 9 | SITC of Power Amplifier Having Max power output 480W or higher, 2 or higher mic or line inputs, 70V/100V line output,Flexible output options: 4-16 ohm or 70V/100V connectivity,Frequency Response from 30 hz or lower to 20khz or higher ,Signal-to-Noise Ratio 70dB or hgiher ,Crosstalk >70 dB or higher. Should have all Protection fetures like Short-Circuit, Over and Under-Voltage, Over-Current, Over-Load, DC Output, Temperature.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 10 | SITC of POWER SEQUENCER ,MCU controlled smart power management system, TFT LCD screen withvoltage + status indicators, 10 channels or higher, controllable power output sockets, with each channel programmable delay on/off time, max 16A output per socket & 60A max total output, Smart over and undervoltage management with cut off, relay on/off with delay timer, RS232/485, network control interface availablecomplete in all respects as approved and desired by the Engineer in-charge at site. |
| 11 | SITC of FEEDBACK SUPPRESSOR HAVING 2 or more balanced inputs and 2 or more balanced outputs, should have 48V phantom power for MIC1/MIC2 with independant gain adjustment, rear panel AFS on/off switch, 48KHz samplfing DSP-based feedback suppressor engineered to eliminate acoustic feedback while maintaining natural sound clarity.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 12 | SITC of Handheld Microphone system having UHF Wireless Cardioid dynamic handheld microphone system with Frequency Response of 100 Hz or lower to 15 kHz or higher (+1 dB, -3 dB), , 60 dBA or higher S/N ratio, Total Harmonic Distortion <1.0% or lower (at 1 kHz, ±20 kHz deviation) , Dynamic Range 110dB or higher , Should have on/off switch, and have operating range 100 mtrs or higher , , Multiple band with 10 or higher channels on each band ; maximum Output level XLR / Balanced: +9 dBV or higher & 6.3 mm (¼\\"\\") / Unbalanced: +4 dBV or highercomplete in all respects as approved and desired by the Engineer in-charge at site. |
| 13 | SITC of Hypercardioid dynamic Neodymium handheld Instrument microphone -HAVING Frequency Response Form 60 Hz or Lower to 14,000 Hz or higher , Open Circuit Sensitivity -54 dB or lower (1.9 mV) re 1V at 1 Pa or better Impedance-600 ohms or better , Should have on/off switch Integral 3-pin gold-plated XLRM-type connector , Rugged all-metal construction , complete with stand clamp and threaded adaptor and Foam Wind Screencomplete in all respects as approved and desired by the Engineer in-charge at site. |
| 14 | SITC of Gooseneck microphone having 5 pin Desk stand with RGB LED Ring,Logic switch Control,Polar Pattern Cardioids Condenser,Gooseneck Length 18\\" or higher ,Frequency Response From 50 or lower to17000 Hz or higher,Open Circuit Sensitivity,Maximum Input Sound Level 121 dB or higher SPL,Dynamic Range 93 dB or higher ,Signal-to-Noise Ratio 66 dB or higher ,Impedance : 100 Ohms or higher ,Output Connector Integral 5-pin XLRM-typeLogic I/O capability permits control of remote devices from the power module’s touch-sensitive capacitive-type user switch RFI shielding.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 15 | SITC of 16 or higher Channel Mixing Console having 10 or higher Mic inputs , 16 or higher Line Inputs, 4 or higher GROUP Buses , 1 or higher Stereo Bus , 4 or higher AUX.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 16 | SITC of Pure Copper Speaker Cable having 2 or Higher cores, Should have 2.5 or higfher Sq mm thichness of each core with proper insulation and shielding.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 17 | SITC of Pure Copper Microphone Cable having 2 or more cores, shouled be sheilded type, and have 20/22 AWG thichness of each core.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 18 | SITC of Customized Mettalic Floor Box with 8 x XLR with standard accessories as required.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 19 | SITC of Powder Coated Mettalic AV Equipment Rack having size 42U Equipment rack to house all rack mountable equipment, with internal wiring, front glass access door,Ventilated Fans,Power Distribution Unit.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 20 | SITC of Various Bulk Connectors, Velco Tap, Cable ties, Audio Connectors such as XLR, Speakon, RCA, Phono and AUX etx, Audio Patch Cable etc as required.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 21 | SITC USB Mixer Player.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 22 | SITC of Network Switch - 16-Port PoE 1G/bit Smart Network Switch, shall have IPv4/ IPv6 network protocol, DHCP settings, DoS, QoS features.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 23 | SITC of 4 Channel Power Amplifier having total output power 4000W or higher , should be Class D Energy Efficient Technolgy , Should deliver 1000 W or higher per channel output power at 70 V/100v and 4, 8 and 16 ohms operation, Should Have THD 0.1% or Lower, Signal to Noise Ratio >102dBA or higher, Frequency Response 20 Hz - 20 kHz or higher, ,Crosstalk 50 db or higher.Should have protection Features Like Mismatched ,Load Short circuit,Thermal,under Voltage,Should have Eq High Pass filters,Limiter.Should Have 1U Rack Mount Size.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 24 | SITC of Digital signal processor Having 16 input or higher(atleast 8 Analog inputs + 8 Digital Inputs) , 16 output or Higher atleast 8 Analog outputs + 8 Digital outputs), Should Have Matrix DSP routing for all inputs and outputs,Should have Dante connectivity for Inputs and Outputs ,Should Have 32-bit or higher floating point processor,24bit/48KHz or Higher sampling rate,In-built USB sound card for USB recording and soft video Conferencing Codec,Acoustic Echo Cancellation (AEC) 8x8 or higher Low pass & high pass filters – and limiter on output channels,8-way GPIO (General purpose input output) configured as inputs or outputs, allowing for flexible control of digital signals,Ethernet, RS232/485 control interface for third-party control, Frequency Response 20Hz - 20kHz, ±0.3dB,Input Dynamic Range 110dB or higher,Output Dynamic Range 112dB or higher,,Input Impedance 5kΩ or higher ,Output Impedance 100Ω or higher ,System delay <3ms. complete in all respects as approved and desired by the Engineer in-charge at site. |
| 25 | SITC of Gooseneck microphone having 5 pin Desk stand with RGB LED Ring,Logic switch Control,Polar Pattern Cardioids Condenser,Gooseneck Length 18\\" or higher ,Frequency Response From 50 or lower to 17000 Hz or higher,Open Circuit Sensitivity,Maximum Input Sound Level 121 dB or higher SPL,Dynamic Range 93dB or higher ,Signal-to-Noise Ratio 66 dB or higher ,Impedance :100 Ohms or higher ,Output Connector Integral 5-pin XLRM-typeLogic I/O capability permits control of remote devices from the power module’s touch-sensitive capacitive-type user switch RFI shielding.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 26 | SITC of CAT 6 with 23AWG solid bare copper conductor, special grade PE insulation with star separator, 4pair Unshielded Twisted Pair (UTP) industrial cable, FR PVC sheathed, Class-E, 250 MHz of bandwidth, supporting data transfer speeds of up to 10 Gbps (10GBASE-T) for distances up to approximately 180 feet, cables are manufactured and tested to meet the ANSI/TIA 568-C.2 and ISO/IEC 11801 Class E standards left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- ( a)CAT 6 LAN cable. |
| 27 | SITC of Network Switch - 16-Port PoE 1G/bit Smart Network Switch, shall have IPv4/ IPv6 network protocol, DHCP settings, DoS, QoS features.complete in all respects as approved and desired by the Engineer in-charge at site. |
| 28 | SITC of 2-way full range all weather Line Array Loudspeaker,Having line Array Stackable Cabinet L.F, 1 x 14” or hIGHER , 1 x 1.4” or higher Horn loaded Compression Driver,750 watt or Lower Continous RMS Power,2000W or Higher Peak Power, 8 ohms, Frequency Response(-10db) 55Hz or Lower and 18khz or Higher, Average Sensitivity - 98dB or higher, Max SPL Peak 135 db or higher, Horizontal Dispersion 60° or higher,Vertical Dispersion 25° or Higher,The Speaker cabinet Should be of IP 55 or higher Rated ,Powder-coated aluminum or Stainless Steel grille,UV-resistant and should have all Corrosion-resistant Components.Complete in all respects as approved and desired by the Engineer in-charge at site. Please Enable Macros to View BoQ information |
