|
| 1 | DSR ITEM NO 1.30 Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16 amps piano type switch, connection, painting etc. as required. |
| 2 | DSR ITEM NO 1.29 Supplying and fixing metal box of 150mm X 75mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch, connections, painting etc. as required. |
| 3 | DSR 1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. |
| 4 | Supply & erection of PVC batten casing & caping of superior quality of size 1 inch on surface with suitable arrangements The job includes all labour & petty material required to complete the job to the entire satisfaction of the E.I.C. of the work.. |
| 5 | Supply & Erection of 9/10 Watt, approx. 2’ Feet Long, surface mounted LED Batten type fitting to be installed on existing surface as required at site complete with connection etc. The LED Batten Fixture should be of Philips / Wipro / Bajaj / Havells / Crompton / Jaquar / Surya / Panasonic/ Trilux/ LT make only. The job includes all labour & petty material required to complete the job in entire satisfaction of Engineer-in-Charge as per complete item no.5 of DNIT. |
| 6 | S/E of fresh air fan high speed motor of following size with copper would 10” sweep with louver and plastic body complete with speed motor, blades, epoxy powder coated of Havells make Ventil Air DX HS/ Orient make ventilator/ Crompton make Brisk Air Neo/ Usha Crisp air/ Bajaj Supreme maxima DXI only. The cost includes the connection with adjacent light points and installed on wall with suitable arrangement by providing frame of required size made out 6mm thick water proof plywood to be installed with suitable size rag bolts, nuts after making suitable size hole in the wall if required at site to the entire satisfaction of Engineer-in-charge. |
| 7 | 8” – 200 mm sweep |
| 8 | 10”- 250 mm sweep |
| 9 | Supply & erection of wall/Cabin Fan 16” sweep oscillating type complete with blades & regulator. The fan should have 2 Nos. of pull cord switches, one for oscillation and one for speed regulation. The fan should be of Usha/ Orient/ Havells/ Bajaj/ Crompton Make only. The cost includes the connection with adjacent light points and installed on wall with suitable size rag bolts, nuts and other material required to complete the job to the entire satisfaction of Engineer-in-Charge. |
| 10 | DSR 9.2 Brush Less Direct Current (BLDC) Fan without RemoteSupply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required.1400mm, service value ≥ 6.0 CM/Min/Watt, air delivery 245 CM/Min (Minimum) |
| 11 | Supply & erection of Exhaust Fan (heavy duty motor with copper wound metallic body) following size complete with motor, metallic blades, double ball bearing with minimum power consumption, rigid frame with rubber mounting for silent operation, epoxy powder coating along with metallic louver to be installed in the existing opening including cost of making the hole in existing wall suitable size of above fan making in original shape of wall. The size of above fan making good the damage, Carriage Charges connection, testing, commissioning etc. as required to complete the job to the entire satisfaction of EIC. The Exhaust fan should be Havells/Orient and Bajaj make only. |
| 12 | Size 12 inches (300mm) Sweep, 900 RPM Heavy Duty Exhaust fan (Single Phase) with louver of Havells make (Turbo Force SP)/ Crompton make ( EXHD300-6-1)/ Bajaj make (Supreme Plus)/ Orient make (Industrial Heavy Duty)/ Usha Make (Turbo HDEF) make only. |
| 13 | Size 15 inches (380mm) Sweep, 900 RPM Heavy Duty Exhaust fan (Single Phase) with louver of Havells make (Turbo Force SP)/ Crompton make ( EXHD380-6-1)/ Bajaj make (Supreme Plus)/ Orient make (Industrial Heavy Duty)/ Usha Make (Turbo HDEF) make only. |
| 14 | Supply and erection of M.S. box for Computer Point of size 10”x8”x3”deep made out of 16 G.M.S. sheet erected in existing wall and covered with 3mm thick white glazed bakelite sheet with provision for 4 Nos. 5 Amp. Socket with control switch of each socket. The job includes the cost of making interconnections with suitable copper wires painting of box with approved paint and other petty material required to complete the job as per satisfaction of Engineer-in-Charge at site. The switch & socket should be of ISI marked Anchor/ Havells/ Gold Medal make only. |
| 15 | S/E of PVC sheathed copper wire following sizes to be drawn in existing pipes. The job includes making connections all labour and petty material required to complete the job to the entire satisfaction of the E.I.C. of the work. The copper wire should be of ISI marked only. |
| 16 | 23./.076 flexible wire 2 core |
| 17 | 1.5sqmm x 3 core double sheathed |
| 18 | 2.5 sq mm x 3 core double sheathed |
| 19 | DSR 8.7 LED Panel light 2x2 ft. (System lumen efficacy ≥120 <135 lm/Watt)Supplying, Installation, Testing & Commissioning of Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) <19, Flicker free,(flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. Complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output.LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).Powder Coated CRCA Sheet Body (Thickness >0.50 mm) |
| 20 | 36 watt |
| 21 | S/E of 2x18/20 LED box type 4’ long fittings made of CRCA Sheet. The fittings should be installed on existing surface. The tube rod and batten for housing the same should be of Philips / Wipro / Bajaj / Havells / Crompton / Jaquar / Surya / Panasonic/ Trilux/ LT only. The job includes carriage, erection, making connections testing and commissioning of the fittings as required to the entire satisfaction of engineer in charge as per complete item no.13 of DNIT. |
| 22 | S/E of 1x18/20 LED box type 4’ long fittings made of CRCA Sheet. The fittings should be installed on existing surface. The tube rod and batten for housing the same should be of Philips / Wipro / Bajaj / Havells / Crompton / Jaquar / Surya / Panasonic/ Trilux/ LT only. The job includes carriage, erection, making connections testing and commissioning of the fittings as required to the entire satisfaction of engineer in charge as per complete ietm no.14 of DNIT. |
| 23 | Supply and erection of 6 way bell indicator of reputing make. The job includes all labour and petty material required to complete the job to the entire satisfaction of engineer Incharge. |
| 24 | Supply & erection combined 15 amp switch & 6 pin 15 amp socket outlet complete PVC Gang box cover from backside & open able from front side of anchor penta make. The job includes all labour and petty material required to complete the job to the entire satisfaction of the E.I.C. of the work. |
| 25 | Supply & erection combined 5 amp switch & 3 pin 5 amp socket outlet complete PVC Gang box cover from backside & open able from front side of anchor penta make. The job includes all labour and petty material required to complete the job to the entire satisfaction of the E.I.C. of the work. |
| 26 | Repair of led fittings of various capacity 70/80/100/120 watt as per requirement of site. The job includes repair /replace PCB and cost of all labour & petty material required to complete the job to the entire satisfaction of EIC of work |
| 27 | Supply and Erection of electronic step type switch type fan regulator of 100 watt min. in existing B.L. Sheet including making connection and petty material reqd. to complete the job. The fan regulator should be of Anchor Panta / Havells Reo/ Gold Medal Essenza make only. |
| 28 | Supply and Erection of electronic step type socket type fan regulator of 100 watt min. in existing B.L. Sheet including making connection and petty material reqd. to complete the job. The fan regulator should be of Anchor Panta / Havells Reo/ Gold Medal Essenza make only. |
| 29 | Supply & Erection of 3 mm thick white glazed bakelite sheet on existing M.S. box. The job includes the cost of sheet and making holes & cutting and fixing with screws as required to complete the job. The Bakelite sheet should be of make Super Hylam/ Formica/ GreenLam make only. |
| 30 | Supply & Erection of LED lamp of following capacity/wattage in warm /white colour in existing holder pin type (B22) & screw type (E27). The job includes cost of all labour & petty material required to complete the job to the entire satisfaction of engineer in charge. |
| 31 | LED lamp 7/9 Watt pin type (B22) |
| 32 | LED lamp 7/9 Watt screw type (E27) |
| 33 | LED lamp 3 Watt pin type (B22) (in Red, Yellow & Blue color) Please Enable Macros to View BoQ information |
