Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | CIVIL WORKS |
| 2 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 5 | Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size). |
| 7 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 9 | DPC : Providing and laying Reinforced cement concrete 1:2:4 (1 cement : 2 coarse sand (Zone III) : 4 graded stone aggregate mix of 20 mm & 12.5mm nominal size) as damp-proof course of 150 mm thick including the cost of centering, shuttering, finishing , reinforcement and mixing water proofing material in cement concrete work etc in doses by weight of cement as per manufacturer's specification complete. |
| 10 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 11 | Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size). |
| 12 | Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto floor V level including plinth. Thermo - Mechanically Treated bars of grade Fe-500D or more |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for all heights :Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Columns, Pillars, Piers, Abutments, Posts and Struts |
| 15 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 16 | 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 17 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 18 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer |
| 19 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile including applying additional coats wherever required to achieve even shade and colour. Two coats |
| 20 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 21 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 22 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two or more coats of Enamel Paint all complete. |
| 23 | Steel work in built up tubular ( round, square or rectangular hollow tubesetc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, and two or more coats of Enamel Paint including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes |
| 24 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 25 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Gutter (600 mm over all girth) |
| 26 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood |
| 27 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood 30 mm thick shutters |
| 28 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick |
| 29 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. |
| 30 | Providing and fixing to existing door frames.30 mm thick Fiberglass Reinforced Plastic (F.R.P) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used all filler material throughout the hollow panel, casted monoolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS : 14856, complete as per direction of Engineer- in-charge. |
| 31 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 32 | Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 125x64x2.50 mm |
| 33 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 34 | Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved, with necessary screws etc complete as per direction of Engineer- in-charge. |
| 35 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm |
| 36 | Providing and fixing bright finished brass handles with screws etc. complete: 350 mm |
| 37 | Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 38 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately). |
| 39 | Providing and fixing of frameless glass door SS Patch Lock with out handle in toughened glass including all necessary screws etc. complete. |
| 40 | Providing and fixing both side 2 nos SS H handle having min 450 mm length in toughed glass door including all necessary screws etc. complete. |
| 41 | Providing and fixing 12 mm thick frameless toughened glass partition of approved brand and manufacture, including top & bottom fixing arrangement counter opening and making necessary holes etc. for fixing required fittings, all complete as per direction of Engineer-in-charge |
| 42 | Partition wall Made of twin layer 12 mm BWR ISI (303 Grade) plywood (Century, Greenply, Fineply or equivalent). Exposed area 1mm laminate and inside 0.8 mm laminate with Hot press (3m or Henkel) Laminate (Brand MERINO, Associate or equivalent) of approved colour and pattern with inside frame work and fixing arrangement as per the design. Partition top and side shall be provided with minimum 80mm width border using 16 mm BWR grade plywood both side of white laminated plywood (top side high glossy finish) with 1.3 mm thick glossy edge band. The frame work should be 16 mm BWR grade plywood. All joints are necessary grooves in laminate to be given the partition is firmly fixed to the floor and wall. Area of unit to be measured in elevation. Note: Only front elevation will be measured. |
| 43 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed vitrified floor tiles polished finish of size. Size of Tile 600 x 1200 mm |
| 44 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size. Size of Tile 600 x 1200 mm |
| 45 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints with white cement and matching pigments etc. |
| 46 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece. |
| 47 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. |
| 48 | Providing and fixing false ceiling with 7.5 mm thick PVC plain panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete including powder coated aluminium frame work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-incharge |
| 49 | ACP : Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding over Aluminium rectangular tube of minimum size 50x25x2mm, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing. The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics including all required & complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in Sqm. up to two decimal places. |
| 50 | FURNITURE WORKS |
| 51 | Double Level Counter: Providing and fixing Double Level Counter, first step at 750 mm from ground, 600mm wide and Counter top at 1050 mm from ground level and 300 mm wide. Counter top shall be provided 25 mm thick Pre-laminated MDF Board, exterior Grade-I, confirming to IS:14587 with 1mm laminated finish on both sides and other sides made up of 18 mm thick pre-laminated medium density fibre board exterior grade (Grade-I) IS: 14587:1998 marked with laminated finish on both sides. The bottom Display unit with 8mm thick toughened glass fascia and 18mm thick pre-laminated shelves to be in built in counter with movable shutter. Counter should contain retractable keyboard trays and partitioned drawers (at every 1200mm) with drawer channel, cupboard units with swing door and auto close hinges. Drawers and cupboard are to be fixed with individual locks and handles. Cable manager and leg space are also to be provided.150mm high SS glossy skirting all Complete as per the design and instructions of engineer in charge. 12mm thick toughened glass partition to be provided above counter up-to roof height with necessary counter opening all complete as per approved design of engineer in charge/Architect. Note: Only front elevation of wooden counter will be measured. (12mm thick toughened glass will be paid separately). Make laminate: Century, Greenply, Merino or equivalent. |
| 52 | Supply, delivery and installation at site of counter height ergonomic stool suitable for continuous 24-hour multi-shift operation, having heavy duty swivel type construction with 360° revolving mechanism and seat height adjustment through Class-4 gas lift mechanism, adjustable from 750 mm to 900 mm or required range. Stool shall have heavy gauge powder coated steel / chrome plated steel / aluminium alloy frame with corrosion resistant finish and stable 5-star heavy duty base fitted with anti-skid nylon shoes or heavy duty castors as approved. Seat shall be ergonomically designed with high density moulded polyurethane foam cushioning and upholstered in premium quality PU / fabric / leatherette finish, with medium height backrest incorporating proper lumbar support. Stool shall be provided with circular adjustable footrest ring and strong fixed / adjustable armrests wherever required. The stool shall have minimum safe load capacity of 120 kg and be suitable for intensive commercial use in control rooms, counters, laboratories, reception areas and similar locations. Item shall be complete with all accessories, hardware, transport, installation, testing and warranty of minimum 3 years, of approved reputed make such as Godrej Interio, Featherlite, Wipro, Chairkraft or equivalent. |
| 53 | Executive Table with Pedestal Unit: Providing and placing in position Executive Table of size 1200 × 600 × 750 mm high with 25 mm thick MDF top finished with approved laminate/melamine finish and 2 mm PVC edge banding on exposed edges. Frame made of 40 × 40 × 1.6 mm thick CRCA steel tubular legs and 50 × 25 × 1.6 mm thick CRCA horizontal members, duly powder coated complete. Table provided with flip cover / cable management box. Including one modular pedestal unit of minimum size 450 × 500 × 650 mm high having three drawers in pre-laminated board with telescopic channels, handles, central locking arrangement, hinges, fittings and accessories complete, as per approved design and direction of Engineer-in-Charge.Measurement: Each complete unit. |
| 54 | Chair: Supply and errection of Medium back ergonomic chair with five nos. Star shaped Nylon base. Castors: 50mm diameter nylon twin wheel, gas lift height adjustment, back angle adjustment and backrest height adjustment. Fixed armrest providing natural resting for arms. Seat with PU cutted foam backed fabric, back rest with mesh type fabric. Upholstery: Heavy duty rubber backed fabric in BLACK. |
| 55 | Medicine Display Shelf: Providing, supplying and placing in position modular self-standing open wooden display laminated cabinets (not fixed to floor/ground), each unit of overall size 900 mm length × 2500 mm height, fabricated from 18 mm thick pre-laminated MDF board, Exterior Grade-I conforming to IS:14587, with decorative lamination on both sides, including all necessary intermediate partitions, racks, shelves, hardware and accessories complete.The cabinet shall consist of a bottom storage/display unit of 600 mm depth, raised 750 mm above finished floor level, provided with sliding shutters or openable shutters as per approved design, and with 2 to 3 display wooden shelves. Above this, an upper display unit of 450 mm depth and 1750 mm height shall be provided over the bottom unit, having 4 to 6 display wooden shelves as per approved drawings and approved pattern.All exposed edges shall be finished with approved PVC edge banding. Shutters shall be fitted with approved quality hinges/channels, handles, locks, stoppers and other necessary fittings. Shelves shall be supported on suitable heavy-duty bracket holders / shelf supports. The unit shall be complete in all respects as per approved layout, drawings and directions of the Engineer-in-Charge.Note: Measurement shall be taken on front elevation area only. |
| 56 | Over Head Storage Cabinet: Providing and fixing of Over head storage cabinet of dimension 900mmX600mmX450mm made up of Pre-laminated MDF Board, exterior Grade-I 18 mm thick confirming to IS:14587 with decorative lamination on both side including inside middle partitions and with sliding door on front side with rollers, sliding channels, handles, locks etc. All the edges to be finished with edge band and shelves to be fix with proper bracket holders complete as per approved layout, drawings and instruction of Engineer In Charge. Note: Only front elevation will be measured. |
| 57 | Airport Chair, 3 Seater: Supply and erection of Airport Chair (Set Of 3 In 1) having overall dimension of Length 1720mm x width 675mm x height 850mm. Chair dimension floor to seat height 400mm and floor to arms height 600mm seat and back frame size Length 495mm x width 490mm x height 550 mm. Chair arms is made up of Stainless Steel Tube 50mm X 25mm Oval Shapes Tube 1.6mm thickness. Legs are made to 48mm Stainless Steel round Tube 2mm thickness and seat and back frame made to 19mm Stainless steel round tube 1.2mm thickness. Seat and back use to 1.2mm thickness perforated Stainless steel sheet. All the end cups are made to stainless steel glossy finish cups and using for the floor levellers 10mm nylon adjustable bush. |
| 58 | DISPLAY WORKS |
| 59 | Backlit Acrilic Board with projected Channel letters: Supply, installation, testing and commissioning of weatherproof backlit acrilic board with projected letters made upof 20 mm thick acrilic board and having box depth of min 100mm in approved size and design with reqired LED strips for high glow light. The board shall be fabricated and fixed over suitable welded and painted 25X25X3mm MS angle frame in suitable location and in proper line and level with all necessary fastners, supports etc. Electrical works likes electrical wirings, connections, fittings, externaly fixed weather proof 2/3 pin plug points and sockets including boxes etc. to be complete properly. All fabrication and fixing should be done as per approved design and instructions of Engineer in Charge. (Note: Only front elevation will be measured.) |
| 60 | Vinyl Transparent One Way Vision Glass Stickers: Supply and pasting of Vinyl Transparent One Way Vision Glass Stickers in approved size and design in glass partition and door as per the instruction of Engineer in Charge. |
| 61 | PVC flex board: Supply and fixing of PVC flex board in approved size and design including all the required steel frames and fixings as per the instruction of Engineer in Charge. |
| 62 | Providing & sticking/pasting of printed vinyl wall stickers as per approved size and design at all heights includes all the required as per the instruction of Engineer in Charge. |
| 63 | SANITARY AND PLUMBING WORK |
| 64 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Angle back wash basin size 400 x 400 mm with single 15 mm C.P. brass pillar tap |
| 65 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 66 | Providing and fixing uplasticised PVC connection pipe with brass unions: 45 cm length15 mm nominal bore |
| 67 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings completeFlexible pipe32 mm dia |
| 68 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore |
| 69 | Providing and fixing SS grating of approved quality and colour. Rectangular type with openable lid150 mm nominal size square 100 mm diameter of the inner hinged grating. |
| 70 | Providing and Fixing in position best quality approved Indian make double type CP brass ROBE HOOK with flanges fixed to wall/door shutter etc. with necessary screws, washers and plugs all as specified and directed. |
| 71 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outlet : Sand Cast Iron S&S as per IS: 1729 |
| 72 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge Concealed work, including cutting chases and making good the wall etc. 15 mm pipe 10kgf/cm2 |
| 73 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Concealed work,including cutting chased and making good the wall etc. 20 mm pipe 12 Kgf/cm2 |
| 74 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 12 kgf/cm2 |
| 75 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 10Kgf/cm2 |
| 76 | Providing and fixing PVC pipes including all fittings like bent, tee, elbow, collar etc complete for jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.75 mm dia. 6Kgf/cm2 |
| 77 | Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in- charge. |
| 78 | Providing and fixing Premium quality CP rectangular shaped soap dispenser holder and soap dispenser with concealed fittings arrangement all complete. |
| 79 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank. |
| 80 | Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately) 50 flush capacity |
| 81 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 82 | Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 83 | CAPITAL/SUPPLY ITEMS |
| 84 | Supply, Installation, Testing & Commissioning (SITC) of 1 No. 3 kVA True Online Double Conversion UPS (2400 W, 0.8 PF) with IGBT/PWM technology, input voltage 160-300V, output 230V ±1% pure sine wave, zero transfer time, LCD display, RS232/USB port, and built-in intelligent battery charger. The UPS shall be supplied with 8 Nos. 12V 150Ah SMF VRLA batteries connected in series with suitable charger mounted on a powder-coated battery rack with necessary interconnecting cables, providing minimum 8 hours backup at full rated load. The system should include all protections, alarms, and meet IEC 62040 standards. Scope includes complete installation, earthing, testing (including backup time verification), commissioning, and training. Warranty: 3 years on UPS and 3 years on batteries. Makes: UPS - Luminous / APC / Numeric or equivalent; Batteries - Exide / Luminous / Amaron or equivalent. |
| 85 | Supply, Installation, Testing & Commissioning of A4 monochrome laser multifunction printer (Print/Scan/Copy) equivalent to with minimum 40 ppm print speed, automatic duplex printing, 50-sheet single-pass duplex ADF, ≥350-sheet paper capacity, 1200x1200 dpi resolution, Wi-Fi/Ethernet connectivity, color touchscreen, ≥512 MB memory, monthly duty cycle ≥50,000 pages, USB cable, starter toner (≥3,000 pages), low running cost high-yield toner options, compact design, compatible with Windows/macOS, Bidder to specify make/model with compliance statement and demonstrate print quality, speed & scan performance at site. 3 Year warranty. make: HP LaserJet Pro MFP 4104dw / Brother MFC-L59xx / Canon imageCLASS MF46x series |
| 86 | Supply, Installation, Testing & Commissioning of monochrome laser printer with minimum 20 ppm print speed, 1200x1200 dpi resolution, manual/auto duplex printing support, 150-sheet input tray, USB/Wi-Fi connectivity, compact footprint (<350x220x200 mm), monthly duty cycle ≥8,000 pages, compatible with Windows/macOS/Linux, including starter toner cartridge (≥1,500 pages yield), USB cable, 3-year on-site warranty, and low running cost toner options. Bidder to specify make/model, compliance, and demonstrate print quality & speed at site. Make: HP Laser 1008a / Brother HL-L24xx series / Canon imageCLASS LBP series |
| 87 | Visi Cooler / Pharmacy refrigerator : Supply, errection and commisioning of lab / pharmacy refrigirator as per following specifications : Upright Showcase Coolers/refrigerators with Single Glass Door and Lock having 350-450 Litre capacity, Temperature range capability 1-10 degree celsius with Digital Temperature Controller and Display, Minimum of 4 adjustable Shelves/Racks. 3 year warranty. Recommended Make: CELFROST, BLUESTAR, VOLTAS, THERMO FISCHER |
| 88 | Client PC - Supply, Installation, testing and Commissioning of All in One computers with following specification. Processor: 14th or Higher Gen Intel® Core™ i3 or AMD Ryzen 3 7th gen or better, Memory: 16 GB: DDR4 or better : Intel® Graphics Storage: 512 GB, M.2 2230, PCIe NVMe, SSD, Class 35 OS: Windows 11 Pro English Chassis: Mini Tower, Wired Multimedia Keyboard and Mouse Integrated Wireless LAN Integrated Gigabit LAN, Separate/Integrated FHD Webcam, Monitor 21.5 LED or higher. Color shall be as per choice of Engineer in charge. 3 year warranty. Make : Dell / HP or equivalent |
| 89 | Server PC - Supply, Installation, testing and Commissioning of all in One type desktop computers. minimum 14th Generation Intel® Core™ i5/ AMD Ryzen 5 7th generation processor, Genuine Windows 11 Pro Single language, MS Office, Intel® UHD Graphics with shared graphics memory, minimum 1.7 GHz base clockspeed, 16 GB, DDR4 or better, 3200MHz, 512GB SSD, 23.8 inch FHD (1920x 1080), Anti- Glare Narrow Border Non Touch Display, with keyboard, mouse and mouse pad. Webcam shall be inbuilt. Color shall be as per choice of Engineer in charge. 3 year warranty. Make : Dell / HP or equivalent |
| 90 | Cash Counting Machine cum Fake Note Detector Make : Optimus-Model No.OLC 04 or equivalent |
| 91 | Cash Safe (Coffer) Volume. 14 L Min WallThickness: 2.5 mm min for body and 5 mm min for door Recommended Make: Godrej make, Model No. Premium Coffer BRN (ltem Code: SEBP 1112) or equivalent (only manual lockinq system) |
| 92 | Counter Communication System : Supply, installation, testing and commisioning of two way counter communication system including speaker, mike, control unit, power unit etc all required (make : Ahuja ccs 2300 or equivalent) |
| 93 | Water Dispenser: Supply and errection of water dispenser can hold 20 litre water bottle having normal standing design with 14 liter refrigerator at bottom and having 3 temperature taps hot, plain and cold. 3 liter cooling and 5 liter heating capacity per hour. Body made of ABS plastic and tank made of Food grade stainless steel. Heavy duty bottle piercer with bottle holder. with min 1 year warranty. (Make : voltas / Blue star/ equivalent) |
| 94 | Supply of ABC Type fire extinguisher of 2 Kgs. Make SAFEX / MINIMAX / CEASEFIRE or equivalent |
| 95 | ELECTRICAL WORK |
| 96 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C |
| 97 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. (Recommended Material : Polycab, RR Kabel, V Guard, Havells) |
| 98 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.( Recommended Material : RR Kabel/National/ Ralison/RKG/ Finolex / Polycab / Havells) |
| 99 | 2 x1.5 sq.mm + 1x 1.5 sq. mm earth wire |
| 100 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 101 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire meter |
| 102 | Supplying and fixing 3 pin 5 A ceiling rose on the exising junction box / wooden block including connections as required. |
| 103 | S/F light plug point modular type accessories : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc as required, |
| 104 | S/F Power plug point with modular type switch : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 and 15/16 amps modular switch, connection,painting etc as required. |
| 105 | S/F 20A SPN MCB industrial socket outlet : Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 106 | S/F Modular boxes, base & cover plate : Supplying and fixing 1 or 2 module ( 75 mm x 75 mm), GI box along with modular base, cover plate for modular switches in recess etc as required. |
| 107 | S/F 'C' series, MCB : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole |
| 108 | S/F 'C' series, MCB : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole |
| 109 | Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps |
| 110 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator16 way, Double door |
| 111 | Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 16 sq mm with factory made clamp |
| 112 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 16 sq. mm (19mm) |
| 113 | Supply, Installation, testing and Commissioning of single phase electronic type energy meter with LCD display with battery backup, class 1.00 CT. The whole unit to be mounted on suitable metal enclosure (powder coated with locking arrangement, separate enclosure for incoming and outgoing) with required HRC fuses/MCB/RCCB as required, Neutral link and all connections complete |
| 114 | Supply, installation, testing and commissioning of the following types of light fittings with all accessories on false ceiling, true ceiling or wall as directed and giving connections with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required. All recessed type fixtures are to be supported independently with chains or GI wire anchored to the ceiling with anchoring bolt of necessary size. All loose wires above the false ceiling are to be neatly concealed by flexible metal/pvc conduits.( cost to include lamps & all consumables also) |
| 115 | Supply and installtion of 30-36W, 230V, 4300 lumen, Recessed Square LED Cool White light fixture of dimession 600mm X 600mm on false ceiling along with all accessories with intergrated driver THD<10% and connections as well as making good the damages as required at site Engineer. Recommended makes: Philips/Crompton/Wipro or equivalent. |
| 116 | Supply and installtion of LED tubelight of 6000K and 20-24W on wall or ceiling as directed and giving connections as required. All loose wires are to be neatly concealed. (Make: Philips, Wipro, Crompton or equivalent) |
| 117 | Supply and installtion of 10-15W, 230V, Recessed Square or Round LED Cool White light fixture on false ceilling along with all accessories with intergrated driver THD<10% and connections as well as making good the damages as required at site Engineer. Recommended makes: Philips/Havells/Wipro or equivalent. |
| 118 | Supply, Installation, testing and commissioning of wall mount fan (400mm sweep), adjustable speed. min 60 degree oscillation, swing, Adjustable upward and downward tilt mechanism, Protective Guard, Including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, mounting accessories, etc. as required. It shall be double ball bearning type. (Make: USHA, Cromption , Havells) |
| 119 | Supply, Installation, testing and commissioning of exhaust fan in the existing opening having 1300-1400 rpm motor speed and 150 mm sweep. bearning type. (Make: USHA, Cromption, Havells or equivalent) |
| 120 | Supply, conveyance, installation, testing and commissioning of ceiling fans of the following sizes using standard accessories excluding resistance type regulator, wiring the down rod with PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required. 1200mm sweep - 5 star rated, 3 blade ceiling fan complete with 300mm down rod , canopies, shackles. |
| 121 | Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required. |
| 122 | SITC of Inverter Air Conditioner: Supply, installation, testing and commissioning of Air Cooled High Wall mounted Split Air Conditioner of following capacity consisting of high wall mounted type room unit with cordless remote control and one number outdoor condensing unit comprising of enegy efficient suitable rotary compressor for operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 3 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1\\" dia drain PVC pipe with insulation 3m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigarant gas, suitable stabilizer etc complete as required. ( Make : Voltas, Carrier, Blue Star, LG, Hitachi ) :1.0 TR 5 star rated as per BEE |
| 123 | SITC of Inverter Air Conditioner: Supply, installation, testing and commissioning of Air Cooled High Wall mounted Split Air Conditioner of following capacity consisting of high wall mounted type room unit with cordless remote control and one number outdoor condensing unit comprising of enegy efficient suitable rotary compressor for operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 3 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1\\" dia drain PVC pipe with insulation 3m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigarant gas, suitable stabilizer etc complete as required. ( Make : Voltas, Carrier, Blue Star, LG, Hitachi ) :1.5 TR 5 star rated as per BEE |
| 124 | SITC of Inverter Air Conditioner: Supply, installation, testing and commissioning of Air Cooled High Wall mounted Split Air Conditioner of following capacity consisting of high wall mounted type room unit with cordless remote control and one number outdoor condensing unit comprising of enegy efficient suitable rotary compressor for operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 3 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1\\" dia drain PVC pipe with insulation 3m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigarant gas, suitable stabilizer etc complete as required. ( Make : Voltas, Carrier, Blue Star, LG, Hitachi ) :2.0 TR 5 star rated as per BEE |
| 125 | Supply and Installation of additional copper piping, cabling and drain piping for air conditioning unit with proper insulation including all required on wall/above false ceiling complete |
| 126 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 127 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 128 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 129 | NETWORK |
| 130 | S/F Modular boxes, base & cover plate : Supplying and fixing 1 or 2 module ( 75 mm x 75 mm), GI box along with modular base, cover plate for modular switches in recess etc as required. |
| 131 | Providing and Fixing of RJ-45 socket outlet in the existing modular box with connections and all required. |
| 132 | 16 Port Network Switch : Supply, Installation, testing and commissioning of : 10/100 Mbps 16-Ports Gigabit Switch . ( Make : D-Link/Netgear) |
| 133 | Supplying,drawing and crimping with all accessories of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.1 run of cable from Port Switch to Data socket |
| 134 | Supply, installation, testing and commissioning of best quality cat-6 patch cord having 1 metre length complete as per specifications as required. |
| 135 | Supply, installation and commissioning of powder coated DVR 4U Wall Mounted Server Rack of ISO Standard of size 550 x 350 x 140 mm having depth adjustable mounting slots, top and bottom Panel with ventilation and cable entry facility, provision to mount the cooling fans on the top panel, lock and key etc. and having capacity to carry a max Load of 60 kg all complete as per the manufacturer specifications and instructions of Engineer In Charge. |
| 136 | Supply, Installation, Testing & Commissioning of Indoor IR Dome night vision cameras : minimum 4.0 MP, minimum 2K resolution, min 20m range, Built-in IR illumination, including complete mounting accessories, connectors complete Make: Matrix/Impact by Honeywell or equivalent |
| 137 | Supply, Installation, Testing & Commissioning of Outdoor IR Bullet night vision cameras : 4.0 MP, minimum 2K resolution, min 20m range, Built-in IR illumination, including complete mounting accessories, connectors complete Make: Matrix/Impact by Honeywell or equivalent |
| 138 | Supply ,Installation, Testing & commissioning of Power supply unit for above camera as speficied by camera manufacturer -12VDC 10A |
| 139 | Supply ,Installation ,Testing & commissioning of Network Video Recorder : 8-Channel Embedded NVR, Real-time, with 2 TB HDD (WD, Seagate) and English OSD, 230VAC. Rate shall be inclusive of all accessories, termination of cables, etc complete. |
| 140 | Supply ,Installation ,Testing & commissioning of 21\\" LED Color Monitor. make :LG / Samsung/ Equivalent. |
| 141 | Supply of Wireless Mouse with mousepad |
| 142 | Supply and Installation of patch panel |
| 143 | 8 Port PoE Switch : Supply, Installation, testing and commissioning of 1 8-Ports PoE Switch suitable for CCTV system . ( Make : D-Link/Netgear) |
| 144 | DISMANTLING AND DEMOLISHING WORKS |
| 145 | Dismantling doors, windows and clerestory windows (steel or wood or Aluminium) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below |
| 146 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar |
| 147 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm |
| 148 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 149 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 150 | Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. |
| 151 | Laying old cement cocrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineerin- charge. (Old CC paver blocks shall be supplied by the department free of cost). Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
