|
| 1 | Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centreto centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board withrecommended jointing compound , jointing tapes , finishing with jointingcompound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed,all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with DSR 12.451 |
| 2 | Providing and fixing factory made Kitchen Cabinet Shutter/Partition 20 mm nominal thickness of approved shade, quality and make, made from rigid foam sheets (Single extruded) having density 600 Kg/cum and laminated on both side by laminate Sheet/PVC foil lamination. Theexposed edges shall be sealed with PVC edge beading of same shade and colour. The shutter shall be fire retardent having necessary screw holding capacity. Shutter shall be fixed to frame using approved hinges with necessary stainless steel screws, all complete as per direction ofEngineer-in-charge.26.10 |
| 3 | Providing and fixing factory made Kitchen Cabinet Shutter/Partition 20 mm nominal thickness of approved shade, quality and make, made from rigid foam sheets (Single extruded) having density 600 Kg/cum and laminated on both side by laminate Sheet/PVC foil lamination. The |
| 4 | S/Fixing of Anodized Aluminum Sections hollow pipe 100 x 44.5 x 2mm thick i/c all Complite SOR ScheduleItem No.29A |
| 5 | S/Fixing of Aluminium Sheet 16 gauge ( 1.5mm Thick) i/c all Complite SOR Schedule Item No.32(17) |
| 6 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete asper the architectural drawings and the directions of engineer-in-charge . |
| 7 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.DSR SI No.11.41.2 |
| 8 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) .D.S.R.no.13.4.1 |
| 9 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.l. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito |
| 10 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar DSR 15.7.4 |
| 11 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm DSR 15.23.1 |
| 12 | Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer .Using M.S. angels 40x40x6 mm for diagonal braces 10.5.1 |
| 13 | Finishing walls with Acrylic Smooth exterior paint of required shadeNew work (Two or more coat applied @ 1.67 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)13.46.1 |
| 14 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour :New work (two or more coats) over and including waterthinnable priming coat with cement primer having VOC contentless than 50 gram/litre 13.41.1 |
| 15 | Wiring point for light point /fanpoint/call bell/exhaust fan point etc with1.5sq.FRLSH PVC insulated multistrand single core copper conductor cable surface/recessed medium class conduit with modular switch, modlar plate suitablegi box and earthing the point with 1.5 mm FRLS PVC insulated copper conducted single core cable etc as require dsr (E&M) 1.10.1 |
| 16 | Wiring for circuit sub main wiring along with earth wirre with the following size off FRLS PVC insulated copper conductor single core cable in surfase / racessedmedium class PVC conduit as required 2x1.5sq mm1x1.5sq ewrth wire dsr (E&M)1.14.1 |
| 17 | Wiring for circuit sub main wiring along with earth wirre with the following size off FRLS PVC insulated copper conductor single core cable in surfase / racessedmedium class PVC conduit as required 2x2.5sq mm1x2.5sq ewrth wire dsr (E&M)1.14.10 |
| 18 | Supply and fixing hexagonal/RoundG.P.fan box of approved make made up of 1.0 mm thick ISI Marked G.P.sheet spot welded Four to Eight holes of 25.4 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed fitted with 300 mm round zink coted M.S Bar X 12 mm& brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material, labour, T&P etc. required for proper completion of the work. SI No. 1149 |
| 19 | Supply of BEE 5 Star rated-1200mm sweep ceiling fans with fan motor of A.C permanent insulation,capacitor rating confirming BEE 5 star rating and IS:374/79 and also comply with IS:1709/1984 with latest amendment. The rated voltge 220/240 volts, 50Hz, 1-ph AC the fan assemble should consists of down rod blades, shackle canopies etc and with double ball bearing system. SI No. 1501 (i) |
| 20 | S&F of 6 Amp to 32 Amp. SPMCB (10 KA) C Curve SI No. 1002 Cat A |
| 21 | P / Fixing Sign Board Please Enable Macros to View BoQ information |
