|
| 1 | B & R Division Items |
| 2 | Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed. |
| 3 | Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 4 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. and dispossing off complete all as specified and as directed. |
| 5 | Demolition of reed lathing, single or double including battens and plaster or chiken wire lathing all as specified. |
| 6 | Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to stores and rubbish off the premises. |
| 7 | Dismantling mild steel work or wrought iron of any description and in any position complete all as specified and as directed. |
| 8 | Dismantling plain or corrugated steel sheeting, any gauge or any thickness as in roof covering, wall cladding, etc.including all necessary staging / scaffolding, etc. as required complete all as specified and as directed. |
| 9 | Dismantling of timber scantling 40 Sqcm and over in section, in any position in unframed work complete all as specified and directed. |
| 10 | Dismantling wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets all as specified and as directed. |
| 11 | Dismantling wooden boarding (eaves board, purlin, rafter etc) of any description fixed in any position with nails complete all as specified and as directed |
| 12 | Demolition and breaking up 100/110mm bore drain pipes salt glazed ware, AC or reinforced concrete set in cement mortar complete all as specified and directed. |
| 13 | Dismantling of 75mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar or PVC drain pipes incl taking out from trenches ng complete all as specified and as directed. |
| 14 | Taking down cement plaster on brick or stone walls etc, including raking out joints, hacking for key scrubing down with water, removal of rubbish off the premises, removal and depositing serviceable materials where directed and leaving the work clear of any plastering. etc complete all as specified and as directed. |
| 15 | Taking down chowkhats or frame with shutters (without taking off shutters from frame) each not exceeding 1.50 Sqm each complete all as specified. |
| 16 | Taking down Chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified. |
| 17 | Taking up or down 15mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 18 | Taking up or down 20mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 19 | Excavating in trenches, n exc 1.50 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/ loose type of soil complete all as specified and directed. |
| 20 | Returning, filling in trenches including spreading, leveling watering and ramming in layers not exceeding 25cm all as specified. |
| 21 | Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point all as specified. |
| 22 | M&L for PCC (1:4:8), Type D2 using 40 mm graded crushed stone aggregate as in foundations, sub-base,filling and mass concrete complete all as specified. |
| 23 | M&L for 25 mm thick cement concrete (1:2:4) type B-0 using (12.50mm graded stone aggregate) as in flooring to receive the topping layers complete all as specified. |
| 24 | Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces of concrete complete all as specified and as directed. |
| 25 | Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete all as specified and directed. |
| 26 | Use and waste formwork to sides and soffits of floor or roof beam, beam hunching, girder, lintels, cantilever, shelves including supports etc for rough finished flat surfaces of concrete complete all as specified and directed |
| 27 | Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed |
| 28 | Use and waste of formwork to cullah hoods, chajja, trough and similar work complete all as specified and directed |
| 29 | Material and labour for Reinforced Cement Concrete nominal mix 1:1.5:3 type A1using 20 mm graded aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed. |
| 30 | Material and labour for providing Reinforced Cement Concrete nominal mix 1:1.5:3 type A1using 20 mm graded aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed. |
| 31 | Material and labour for providing Reinforced Cement Concrete nominal mix 1:1.5:3 type A1 using 20mm aggregate as in slab supported on walls , beams, and column in floors, roof, landing, balconies, canopies, deck slab and in shelves and like etc comlpete all as specified and directed. |
| 32 | Material and labour for providing Reinforced Cement Concrete nominal mix 1:1.5:3 type A1 using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5 m complete all as specified and directed. |
| 33 | Material and labour for providing Reinforced Cement Concrete nominal mix 1:1.5:3 type A1 using 20 mm graded aggregate as in chajjas complete all as specified and directed. |
| 34 | M & L for 10mm dia and over TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 35 | M & L for 6mm to 8mm dia and over TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 36 | M & L for Mild Steel TMT Bar 6mm dia and over up to 10 mm dia as in stirrups, spacers and binders as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed |
| 37 | M & L for brickwork with subclass 'B' or locally available best quality old size bricks, straight or curved on plan exc 6 m mean raduis, built in CM (1:6) complete all as specified and directed. |
| 38 | M & L for half brick work in cement mortar (1:4) straight or curved on plan to any radius with locally available Subclass ‘B’ old size best quality bricks all as specified . |
| 39 | M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick wall or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified. |
| 40 | M & L rendering 15 mm thick cement mortar (1:4) in two layer each of 10+5 mm thick on fair faces of brick wall or concrete surfaces with water proofing compound @ 3% of wt of cement, mixed with mortar for second layer 5mm thick, finished fair and even without using extra cement complete all as specified. (Note :WPC shall be measured and paid separately). |
| 41 | Supply only integral water proofing compound WPC complete all as specified. |
| 42 | Material and labour vitrified light shade ceramic tiles 8 mm thick ( square/rectangular) area of each tiles exc 0.118sqm but not exc 0.36 sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15 mm thick screed bed or bedding layers in cement mortar 1:6 over brushing with neat cement slurry as specified |
| 43 | Material and labour vitrified light shade ceramic tiles 8 mm thick ( square/rectangular) area of each tiles exc 0.118sqm but not exc 0.36 sqm as in skirting/dado, vertical surface etc. set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick backing coat in cement mortar 1:4 on skirting/dado on walls all as specified and directed. |
| 44 | Material and labour Non-skid coloured ceramic tiles 7 to 8 mm thick ( square/rectangular) area of each tiles exc 0.11 sqm but not exc 0.18 sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15 mm thick screed bed or bedding layers in cement mortar 1:6 over brushing with neat cement slurry as specified |
| 45 | M & L Glazed ceramic coloured tiles in vertical surface size 450mm x 300mm x & ( 6mm to 7mm )mm thick as in skirting, dado etc set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick backing coat in cement mortar 1:4 on skirting/dado on walls all as specified and directed. |
| 46 | M&L Machine cut kota stone slab 20-25mm thick as in flooring laid over 15mm thick cement screed bed in cm 1 : 6 with cement slurry @ 4 kg/sqm jointed and pointed with grey cement slurry mixed with pigment to match the shade of slab including cutting rubbing and polishing to achieve mirror finish complete all as specified and as directed. |
| 47 | M&L for 18-20mm thick granite stone slab, of any type, (table rubbed and polished), in steps, jambs, pillars, window cills, cooking platforms and the like in laid over and including 20mm thick screed in cement mortar (1:4) (rate shall be included) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of slab incl rounding edges complete all as specified and as directed. |
| 48 | Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed . |
| 49 | Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed . |
| 50 | Supply and fix for eves gutter with 1mm thick MS sheet, galvanised, class 3, half round, 200mm dia with rounded edges complete all as specified and directed. |
| 51 | S&F plates (plain or chequered) channels, square cut or notched (ordinay and counter sunk) forming holes, without any attachment of Fe 290 (Gde-E -165) Quality 'A' complete all as specified and directed by Engr-in-Charge. |
| 52 | Supply and fix structural steel work in tubular/hollow sections trusses , Purlin , posts, rafter etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as as specified and directed. |
| 53 | M & L for 12 mm thick Prelaminated particle board,Exterior grade, prelaminated on both side with decorative choice lamination & other side balancing white lamination, all as directed. |
| 54 | S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including necessary jointing cleats, screws etc & fixed complete all as specified & directed. |
| 55 | S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified & directed. |
| 56 | S&F 3 way sliding anodised aluminium glazed window shutter with frame with the following specifications complete all as specified and as directed.(a) Frame 3 track of size 95x25x1.5mm thick(b) 35x25x1.5mm Z section in stiles, rails(c) 35x35x1.5mm T section mullion(d) PVC gasket and with 4.8mm thick coloured glass pane one side mirror finished, area not exceeding 0.5sqm each with aluminium handles and necessary locking arangements(e) Stainless steel wire mesh for mosquito proofing arrangement all as directed |
| 57 | S&F 2 way sliding anodized aluminium glazed ventilator shutter with frame consists of following specification complete all as specified and as directed(a) Ventilator frame 2 track of size 60x25x1.5mm thick(b) Stiles and rails of size 35x25x1.5mm(c) 35x35x1.5mm T section mullion(d) PVC gasket with 4mm thick tinted glass, including aluminium handles with necessary locking arrangement Please Enable Macros to View BoQ information |
| 58 | S&F 2 way sliding anodized aluminium glazed ventilator shutter with frame consists of following specification complete all as specified and as directed(a) Ventilator frame 2 track of size 60x25x1.5mm thick(b) Stiles and rails of size 35x25x1.5mm(c) 35x35x1.5mm T section mullion(d) PVC gasket with 4mm thick tinted glass, including aluminium handles with necessary locking arrangement Please Enable Macros to View BoQ information |
