|
| 1 | Sch 'A' Part-I (B/R works)Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm th (below or above ground level), complete all as specified and directed. Note: No extra cost to be borne by govt in r/o flooring overleaped with tile mozzic floor incl screed .Thickness to be considered as total thickness of overleaping. |
| 2 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed. |
| 3 | Demolition of Brick/stone work built in cement mortar of any description including all necessary quions arches piilars etc, complete all as specified and directed. |
| 4 | Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulaton boards/slabs/blankets, any thickness, including cover fillets, complete all as specified and directed. |
| 5 | Dismantling of Plain or corrugated steel sheeting or any other type, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed. |
| 6 | Dismantling timber scantling, in fillets, rails, posts, rafters, purlin, etc under 40 sq.cm in section, complete all as specified and directed. |
| 7 | Dismantling timber scantling 40 sqm and over in section fixed to any position as in unframed work, complete all as specified and directed. |
| 8 | Dismantling mild steel work of any description not otherwise provided for, complete all as specified and directed. |
| 9 | Taking down cement plaster on brick/stone or conc surfaces including racking out joints hacking for key to any thickness scrubbing down with water etc, complete all as specified and directed.Note : No extra cost shall be borne by Govt exchequer for any no of layers over leaping of tiles / mosiac finish. |
| 10 | Taking down chowkhats with shutter (without taking of from shutter) exc 1.5 sqm and n exc 4 sqm each and removing to store and making good to surface disturbed due to taking down, complete all as specified and directed. |
| 11 | Taking down chowkhats with shutter (without taking off from shutter) n exc 1.5 sqm each and removing to store, complete all as specified and directed. |
| 12 | Taking down shutters of any description exc 1 sqm but n exc 2 sqm each, complete all as specified and directed. |
| 13 | Taking down and re fixing same opening after easing and adjusting of Wooden/Auminium /PVC shutters of any description exceeding 1 Sqm but not 2.00 sqm each, complete all as specified and directed . |
| 14 | M & L for mild steel TMT bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. |
| 15 | All as per Item No 14.00 here-in-before but exc 5mm dia upto 10mm dia. |
| 16 | M&L for formwork to sides and soffits of floor or roof beam, beam hunching, girders, lintel, cantilevers, shelves including suports, overhangs etc, complete all as specified and directed. |
| 17 | M&L RCC (1:2:4) type B-1 (using 20mm gradded stone aggregate) as in beams, deck slabs, chajjas and in shelves and like, complete all as specified and directed. |
| 18 | M&L for stone walling of random rubble masonry, uncoursed, well bonded, bedded and soilidly hearted, built in cement mortar (1:6), complete all as specified and directed. |
| 19 | All as per item No 18.00 here-in-before but except stone. |
| 20 | M&L for extra over stone walling of any type of stone for hammer dressing to face stones and dressing of face beds with maximum depression on face from straight edge held against the dressed surface n exc 40 mm and joints, as specified, of random rubble walling, uncoursed or brought upto courses, complete all as specified and directed. |
| 21 | M&L for brick work with sub class 'B' bricks, old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6, complete all as specified and directed. |
| 22 | M&L for old size half brick work with sub class 'B' bricks straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed. |
| 23 | M&L for PCC type B1 (1:2:4) (using 20 mm graded cushed stone aggregate) as in coping, bands, benching, bed blocks of hold fast and the like including form work, complete all as specified and directed. |
| 24 | Erection and Refixing of Roof trusses (framed), trussed, purlins, Rafter, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed. |
| 25 | S&F rolled section as in main and cross beams, hip and jack rafters, purlins, Vertical post where connected to common rafters and running rails and guides for sliding gates, doors fixed with angle cleats or other connecting plates, complete all as specified and directed. |
| 26 | S&F Mild steel screw bolts exc 5 cm length not exc.10 cm length(machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square dia of shank 11 to 15mm, complete all as specified and directed |
| 27 | S&F Mild steel holding nut bolts exc 22.5 cm length not exc.30cm length (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square dia of shank 11 to 15mm, complete all as specified and directed. |
| 28 | S&F (plain or chequered ) channels, square cut or notched ( oridinary and counter sunk) forming holes, w/o any attatchment, complete all as specified and directed. |
| 29 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour (multi colour pattern as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 30 | S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of approved colour (multi colour pattern as approved by GE) having tensile strength of 550 Mpa as in ridge, fixed with self tapping screws, complete all as specified and directed. |
| 31 | M&L for rendering 20mm thick in cement mortar (1:4) on stone masonry surface, finished even and smooth without using extra cement, complete all as specifed and directed. |
| 32 | M&L for rendering 20 mm thick in cement mortar 1:6 on stone masonry surface, finished even and smooth without using extra cement, complete all as specified and directed. |
| 33 | M&L for rendering 10 mm thick in cement mortar 1:6 on brick masonry surface or concrete work, finished even and smooth without using extra cement, complete all as specified and directed. |
| 34 | M&L for rendering 15 mm thick in cement mortar 1:4 on brick masonry surface or concrete work, finished even and smooth without using extra cement, complete all as specified and directed. |
| 35 | S&F factory made MS tubular Box type window of MS rolled steel section conforming to IS-1038 and shall be ISI marked manufactured by ISI approved manufacturer, openable frames shall be fabricated of sections as approved by GE, corner welded to form a solid fused welded joint handles shall be of z section welded with openable frame box steel section used in outer frame shutter frame and central frame shall be ERW secton of 16 gauge with fixing lugs to be fixed as per provision of IS-1038 except that top lugs shall not be provided , all shutters of windows shall be provided with 4 Nos friction free hinges, 2 Nos 75 mm tower bolts to each leaf of window one at top and one at bottom welded on 3 mm thick steel sheet piece of suitable size which shall be in turn welded to z section of steel window to provide suitable arrangement of using tower bolt. Glazed, gauged window, mild steel casement stays 300 mm with hinged joint and two plates with studs complete all as specified with all fittings and fixtures without glazing bars, including 3mm sheet glass, stainless steel wire mesh of 0.56 nominal dia and average width of aperature 1.18 mm, etc, complete all as specified and directed. Note -All as per Drg No- CEUZ /TD/ 1517/15 Sheet No-1/3,2/3,3/3. |
| 36 | S&F Factory made MS tubular box type ventilators with of MS rolled steel section conforming to IS-1038 and shall be ISI marked manufacture by ISI approved manufacture,openable frames shall be febricated of section, complete all as specified and directed. |
| 37 | S&F of guard bars/grills as specified in between glazed and fly proof window shutter (sand witching guard bars/grill) as per drg No CEPZ/TD-325/07 dt 04.12.07 primer coated, complete all as specified and directed. |
| 38 | S&F 1.25 mm thick pressed steel door frame of size 125x60mm for doors with one or more rebates incl supplying and fixing necessary fixing lugs, hinges lock strike plate etc, complete all as specified and directed. |
| 39 | S&F 1.25 mm thick pressed steel door frame of size 105x60mm for doors with one or more rebates incl supplying and fixing necessary fixing lugs, hinges lock strike plate etc, complete all as specified and directed. |
| 40 | M&L for PCC 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) as in back filling of pressed steel frame, complete all as specified and directed. |
| 41 | S&F Plain framed, panelled shutters (any number of panels) with pannel of timber flat on both sides (feather edged) or of veneered particle board with commercial face veneers 35 mm thick 2nd class hard wood supplied and fitted to chowkats, complete all as specified and directed. |
| 42 | M&L for 35 mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass, etc, size of members of shutter as specified in SSR Part-I, Section 8, clause 8.20 (a), fitted to chowkats, complete all as specified and directed. |
| 43 | S&F for 300mm ordinary rat tail rod pattern springs including roller and rollar plate, complete all as specified and directed. |
| 44 | S&F Stainless Steel wire cloth 0.36 mm any position nominal dia of wire and 1.2 mm average width of aperture fixed with tinned tacks or galvanised wire staple, complete all as specified and directed. |
| 45 | S&F Aluminium handles, cast type, anodised 150mm long, complete all as specified and directed. |
| 46 | S&F aluminium, anodised barrel tower bolts of extruded section and fixed of size 200 mm long, complete all as specified and directed. |
| 47 | S&F aluminium alloy anodised sliding door bolt with fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed of size 200 mm, complete all as specified and directed. |
| 48 | M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base finished even and rough, complete all as specified and directed. |
| 49 | M&L for 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, complete all as specified and directed. |
| 50 | M&L for Vitrified tiles coloured 600x600mm, 10 mm thick as in floors jointed in neat cement slurrry and pointed in white cement slurry to match the shade of existing, complete all as sepcified and directed |
| 51 | All as per Ser item No 50.00 here-in-before but on vertical surfaces such as dado/skirting. |
| 52 | M&L for Non Skid ceramic tiles (size of each tile exc 0.06sqm and n exc 0.11 sqm) 7 to 8 mm thick laid and jointed with cement slurry (in portions) and pointed with coloured cement to match in floor colour, complete all as specified and directed. |
| 53 | M&L for rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:3, finished surface even and fair for receiving tiles as in dado/skirting, complete all as specified and directed. |
| 54 | S&F galzed ceramic coloured tiles as on vertical surfaces 300 x 600 x 7 to 8 mm thick set and jointed in neat cement slurry (in portions) and pointed with white or colored cement to match, complete all as specified and directed. |
| 55 | S&F 18-20 mm thick machine cut kota stone slab (area of each slab nexc 0.36 SSqm except space constraint) in flooring laid and jointed with gry cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing as in repairs over and including 15mm thick screed bed in CM 1:6, roughing the surface including dismantling work, complete all as specified and directed. |
| 56 | All as per item No 55.00 here-in-before but as in riser to steps, skirting ,dado,window cills fixed with cement mortar 1:4, complete all as specified and directed. |
| 57 | M&L for granite 16-18 mm thick of any type work table rubbed and polised in steps, jambs, pillars, window cill, cooking plateforms and like in cement mortar 1:4 including pointing cement mortar 1:2 using marble dust with admixure of pigments to match with shade of granite including demolition of old granite, complete all as sepcified and directed. |
| 58 | S&F for curtain rod of stainless steel 25 mm dia fancy type complete and hanging hooks/brackets / end caps of length 1.5 mtr to 1.8 mtr, complete all as specified and directed. |
| 59 | M&L for providing & fixing of 4mm thick designer ceiling board in ceiling fixed with screw as per manufactures instructions, laid on hot dipped galvanized iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick galvanized steel sheet & of size 24x32x300mm and spaced at 12mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4mm dia to be fixed by approved rowl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall flush fitting of 1200 long cross tee with (double stitching) to be inter locked between main runners at 600mm centre to from 1200x600mm modules cross tee longer than 600mm modules to be formed by fitting 600mm long cross tee, tee perimeter wall angle shall be of 0.45mm thick galvanized steel of size 19x19mm and 300mm long of white colour, complete all as specified and directed. |
| 60 | S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet, reinforced with MS square tube supplying and fixing in opening as per specification and drawing, complete all as specified and directed. . |
| 61 | S&F Factory made solid panel PVC shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘ C’ channel having a PVC sheet strip 20 mm width struck inside with solvent cement for style and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the styles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification and drawing in SSR part-II and as per sample kept in office of GE, complete all as specified and directed. |
| 62 | M&L for providing 75mm cement concrete, type C-1, 1:3:6, (using 20mm graded crushed stone aggregate) as in plinth protection, laid in slope 1:12 from outer edge of the wall, finished even and fair, laid in alternate bays including providing 6mm wide joints throughtout thickness of plinth protection in concrete bays and in between walling and plinth protection, joints filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand (all by weight), complete all as specified and directed. |
| 63 | S&F Rotational moulded polythene water storage tank (cylindrical vertical with closed top)hoisted and fixed in position of 1000 ltrs capacity with and including tank nipple including dismantling of tank, complete all as sepcified and directed.Note : The water tank shall be double layer IS Marked duly embossed on face and weight as per IS specifications. |
| 64 | S&F ball valves suitable for 20mm bore iron pipe high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms), complete all as specified and directed. |
| 65 | S&F in repair 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in new or old position, complete all as specified and directed. |
| 66 | S&F for 15 mm bore galvanised steel water tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors etc, complete all as specified and directed. |
| 67 | S&F for 20 mm bore galvanised steel water tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors etc including taking down of old GI pipe, complete all as specified and directed. |
| 68 | Refixing 15 mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors including taking down of old GI pipe, complete all as specified and directed. |
| 69 | Refixing 20 mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors, including taking down of old GI pipe complete all as specified and directed. |
| 70 | S&F in repair bib taps 15mm bore chromium plated, fancy type, cast copper alloy with crutch, butterfly handle screw down, screwed for iron pipe or for brass, complete all as specified and directed. |
| 71 | S&F in repair 15mm bore angle / Stop valve, cast copper alloy screwed down, high pressure with crutch, or butterfly handle, chromium plated, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. |
| 72 | S&F in repair for 15mm bore Stop valve (concealed type), cast copper alloy screwed down, high pressure with crutch or butterfly handle, chromium plated, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. |
| 73 | S&F in repairs for 15 mm CP Mixer for mixing hot and cold water for wash hand basin screwed down for 15mm pipe, complete all as specified and directed. |
| 74 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed. |
| 75 | S&F in repair 32/40 mm dia PVC waste pipe for WHB/Sink /Urinal (Minimum weight 45 to 60 gms), complete all as sepcified and directed. |
| 76 | S&F repair for PVC connection 15 mm x 450 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore, complete all as sepcified and directed. |
| 77 | S&F in repair 32mm waste fittings brass chromium plated for glazed ware basins,sink etc with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed, complete all as sepcified and directed. |
| 78 | S&F in repair Viterous china wash down water closet pan (pedestal pattern ), white (excluding flushing cistern, flush pipe, complete all as sepcified and directed. |
| 79 | S&F in repair WC Orisa pattern white with integral foot rest 580x440 mm incuding PCC bedding and making good disturbed floor connecting to trap and flush pipe, complete all as sepcified and directed. |
| 80 | S&F in repairs 10 Ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, complete all as sepcified and directed. |
| 81 | S&F in repair Vitreous China wash basin, white, flat back, size 550x400 mm including waste coupling wate pipe and brackets, complete all as sepcified and directed. |
| 82 | S&F in repair viterous China urinal half stall type white including CP spreader holding screws, waster pipe etc, complete all as specified and directed. |
| 83 | S&F SS Gratings of 100 mm dia, fixed in repairs, complete all as sepcified and directed. |
| 84 | M&L in repair 75mm dia outlet of in PVC SWR floor trap plain with grating including jointing with solvent cement including removing old trap and make good existing floors etc, complete all as sepcified and directed. |
| 85 | S&F in repair 110mm bore PVC (SWR) pipe single socketed, in any length with rubber joints laid in floor /ground, complete all as specified and directed. |
| 86 | S&F in repair 75mm bore PVC (SWR) pipe single socketed , in any length with rubber joints laid in floor/ground, complete all as specified and directed. |
| 87 | S&F in repair 75mm bore PVC (SWR) pipe single socketed , in any length with rubber joints fixed to walls, complete all as specified and directed. |
| 88 | S&F in repairs PVC(SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed. |
| 89 | S&F 110mm bore PVC (SWR) pipe bends any radius withoval acess, complete all as specified and directed. |
| 90 | S&F 75mm bore PVC (SWR) pipe bends any radius with oval acess, complete all as specified and directed. |
| 91 | M&L for PVC(SWR) reducer 110mm to 75mm bore jointing with solvent cement, complete all as sepcified and directed. |
| 92 | M&L for PVC (SWR) bend any radius of 75mm bore, complete all as specified and directed. |
| 93 | S&F PVC 'S' or 'P' trap 110 mm bore (SWR) fixed in repairs and jointed, complete all as sepcified and directed. |
| 94 | M&L for preparation of old decorated plastered surface of walls and applying one coat of oil bound distemper, complete all as sepcified and directed. |
| 95 | M&L for preparation of old decorative surfaces of wall and applying one coat of cement base paint (multi colour pattern as approved by GE), complete all as specified and directed. |
| 96 | M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash, complete all as sepcified and directed. |
| 97 | M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint (multi colour pattern as approved by GE), over a coat of primer, complete all as specified and directed. |
| 98 | M&L preparation of new plastered surface of walls and applying two coats of oil bound distemper, complete all as sepcified and directed. |
| 99 | M&L for applying two coats of synthetic enamel paint over a coat of pink primer on new or previously untreated wood and wood based surface incl preparation, complete all as sepcified and directed. |
| 100 | M&L for applying one coat of synthetic enamel paint over on old wood and wood based surface including preparation, complete all as sepcified and directed. |
| 101 | M&L preparation of new of previously untreated steel or iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of Synthetic enamel paint over a coat of red oxide primer, complete all as sepcified and directed. |
| 102 | M&L preparation of old painted steel or iron surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as sepcified and directed. |
| 103 | M&L for PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in surface channels and drains including all necessary form work, complete all as sepcified and directed. |
| 104 | Extra forming fair finished drain or channels 30cm inner girth in cement concrete using extra cement including forms, mould, mitred/stopped ends etcr, complete all as sepcified and directed. |
| 105 | Site clearance in soft/loose soil, complete all as sepcified and directed. |
| 106 | Excavation in trenches for foundation etc not exc 1.5m wide and not exc 1.5 m in depth in soft/loose soil, complete all as sepcified and directed. |
| 107 | Returning filling in including spreading levlling ,watering and well ramming in layers nexc 25cm thick, complete all as sepcified and directed. |
| 108 | Removal of excavated material to a distance n. exc 50 m and depositing at a level nexc 1.5 m above the starting point, complete all as sepcified and directed. |
| 109 | M&L cement concrete (1:4:8) type D2 (using 40mm graded stone aggregate) as in foudation, filling, sub base and mass concrete, complete all as sepcified and directed. |
| 110 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; verticle or to batter complete all as specified and as directed. |
| 111 | M & L for RCC design Mix M-25 (using 20 mm greaded Stone Aggregate) as in foundations, including rafts, footings, foundation, beams, plinth beams, bases for columns, etc; basement slabs, under-reamed piles and mass concrete, complete all as sepcified and directed. |
| 112 | Formwork to sides of pillars, posts, struts, piers,columns, and stanchions complete all as specified and as directed. |
| 113 | M & L for RCC design Mix M-25 (using 20 mm greaded Stone Aggregate) as in columns, pillars, piers, posts and struts, complete all as sepcified and directed. |
| 114 | Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, chajjas etc. also splays between floors and beams, etc, complete all as sepcified and directed. |
| 115 | M & L for RCC design Mix M-25 (using 20 mm greaded Stone Aggregate) as in Beams, cantilevers, bressummers, lintels over, complete all as specified and directed. |
| 116 | Formwork to soffits of suspended slabs such as roof slab, floor slabs, landings and simillar works, not exceeding 200mm thick, complete all as sepcified and directed. |
| 117 | M & L for RCC design Mix M-25 (using 20 mm greaded Stone Aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slab and in shelves and the like, complete all as sepcified and directed. |
| 118 | M&L TMT 5mm dia and over upto and incl 10mm dia in stirrups, spacers and binders, complete all as sepcified and directed. |
| 119 | Supply only integral water proofing compound conforming to IS, complete all as specified and directed. |
| 120 | M&L for 40 mm thick for damp course to horizontal surfaces in cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) including all necessary form work, complete all as specified and directed. |
| 121 | M&Lfor 75 mm thick Cement concrete type D-2, 1:4:8 (40mm graded stone aggregate) in sub base of floor, complete all as specified and directed. |
| 122 | M&L for glazed coloured ceramic tiles in dado/vertical surface (350mm x250mm x 7 mm/450x300x7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface, complete all as specified and directed. |
| 123 | M&L for Rendering 15 mm thick on brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement, complete all as specified and directed. |
| 124 | S&F factory made pressed steel frame box type window/Ventilator with side huge shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement and one coat of red oxide primer, complete all specified and directed.Note : (i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889(ii) MS fillets, glazing, wire gauge shall be measured and paid separately. |
| 125 | M&L for framed work such as guard bars etc, complete all as specified and directed. |
| 126 | S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares n exe 0.5 sqm each pane, complete all as specified and directed. |
| 127 | Supply and fixing of 100 mm But hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and directed. |
| 128 | S&F for 150mm size aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed. |
| 129 | S&F for PVC (SWR) junction double, (double T), 75mm bore, equal or unequal, complete all as specified and directed. |
| 130 | S&F for PVC (SWR) vent cowl 75mm, complete all as specifed and directed. |
| 131 | M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash, complete all as specifed and directed. |
| 132 | Construction of On site RCC Hume Pipe septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc, complete for complete for 10 users, complete all as specifed and directed. |
| 133 | M&L for Soakage well execution, in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete of size 1.8 M dia X 3.0M deep, complete all as specifed and directed. |
| 134 | M&L for PCC.1:3:6 type C2 (using 40mm graded stone aggregate) as in foundation mass concrete, complete all as specifed and directed. |
| 135 | M&L for PCC 1:3:6 type C2 as in bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested for Salt Glazed Stoneware pipe 150mm dia, complete all as specifed and directed. |
| 136 | M&L for precast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregates) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and setting in mortar complete with joints to match , set in cement mortar 1:4. complete all as specified and diredted. |
| 137 | M&L for reinforced concretre pipes, class NP 2 150mm bore dia, laid and jointed complete with collars, complete all as sdpecified and directed. |
| 138 | Sch 'A' Part-II (E/M works)Taking down unserviceable aluminium point wiring (light, fan, socket or power) complete, including all fitting and fixtures such as switches, ceiling roses, pendants, regulators sockets, light fittings etc.) removing material for taking credit (credit for above items should be made as per conditions separately) and making good the disturbed, complete all as specified and directed. |
| 139 | Material and labour for point wiring with 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall/ceiling including modular metal flush box, modular white cover plate with frame, blanking plate etc suitable for Mylinc / Coral / Sleek model accessories etc and making good to the disturbed surfaces to match the existing complete all as specified and directed for one light point controlled by one, one way switch 06 Amps.Note :- Rate is inclusive of Cutting/chases of wall/floor/ceiling |
| 140 | One light point/ fan point controlled by one switch, one way |
| 141 | One switch socket outlet 3pin, 5 Amp point controlled by one switch one way on independent switch board. |
| 142 | One socket out let 6 Amps 2/3 pin, point controlled by one switch one way on same switch board |
| 143 | All as per item No 139.00 here-in-before, but point wiring 2.5 sqmm for switch socket combination for 15Amps point controlled by one switch. |
| 144 | M&L for modular switch piano, 1 module, 6 Amps SP one way 230 volts, complete all as specified and directed. |
| 145 | M&L modular socket outlet 3 pin, 2 module, 6 Amps, 230 volts, ISI marked, complete all as specified and directed. |
| 146 | M&L modular switch, 1 way, 16 Amps, 1 module, 230 volts, complete all as specified and directed. |
| 147 | M&L for modular socket outlet, 6/16 Amps, 2/3 Pin, 2 module, 230 volts, complete all as specified and directed. |
| 148 | M&L for ceiling rose surface bakelite 3 terminals, PVC/ Polycarbonate, isolated body, complete all as specified and directed. |
| 149 | S&F in repair modular fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100%, 240 volts AC and connecting electrically, complete all as specified and directed. |
| 150 | S&F in replacement LED Tube light fitting, 1x 20 watts. Decorative ultra slim linear LED lighting fixture with co extruded polycarbonate body, environmental friendly, energy efficient ready to use pack complete rewired, Premium 20 W LED batten, connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core, including removing old/unsv, complete all as specified and directed. |
| 151 | S&F lamp holder insulated body, PVC/ Polycarbonate type with back plate suitable for batten/ angular/ pendent holder fittings, complete all as specified and directed. |
| 152 | S&F LED lamp 7/9/10 watt suitable for lamp holder, complete all as specified and directed. |
| 153 | S&F in replacement of sheet metal enclosure MCB DB, SPN 240 volts 4 way with IP-43 IK-09 protection double door 200A complete with appropirate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specificaiton, complete all as specified and directed.Note: MCBs will be measured separately. |
| 154 | S&F in replacement of sheet metal enclosure MCB DB, SPN 240 volts 8 way with IP-43 IK-09 protection double door 200A complete with appropirate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specificaiton, complete all as specified and directed.Note: MCBs will be measured separately. |
| 155 | S&F MCB SP 240 volt any rating from 6 to 40 Amps conorming to IS 8828 of 1996, with rupting capacity 10KA including providing thimble for out goint cable complete all as specified and directed. |
| 156 | S&F MCB SPN 240 volt any rating from 6 to 40 Amps conorming to IS 8828 of 1996, with rupting capacity 10KA including providing thimble for out goint cable complete all as specified and directed. |
| 157 | S&F in replacement LED building security light 35 watt with pressure die-cast housing with individual LEDs as light source and lense embedded PC cover having TOP opening separate driver compartment with IP-66 protection and impact resistance of IK-07 complete with connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 1.0 sqmm, complete all as specified and directed. |
| 158 | M&L for street light bracket made up of 40mm bore light grade GI pipe 1.2mtr long including necessary bending, welding etc, complete all as specified and directed. |
| 159 | S&F LED light fitting 1 x 9Watt/ 1 x 10Watt bulk head luminairies including LED light driver holder etc complete with all accessories and including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed. |
| 160 | M&L for earthing with galvanised steel earth plate electrode 600mm x 600mm x 6 mm burried directly in ground earth pit not less than 2.25 mtr deep below normal ground level with top edge of the plate vertically to a depth not less than 1.5 mtr below ground level connected to connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 including GI pipe 15 mm dia light grade for protection to the extend of 7.5 mtr as earthing lead connecting to equipment with provn charcol and salt complete including PCC chamber with RCC cover watering arrangement with GI pipe 20 mm dia medium grade and MS funnel, including excavation and earth work and returning, filling in including ramming and removal of surplus soil and testing on completion complete. |
| 161 | M&L for replacement of service cable of size 6 sqmm 2 core, 1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor, served with an inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm suspension wire or down in and including medium grade non metalic rigid PVC conduit as per site requirement, flat or circular, complete all as specified and directed. |
| 162 | Supply & Laying of 25 mm bore galvanised steel water tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in trenches/wall/floor etc, complete all as specified and directed. |
| 163 | S&F 25 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 164 | Cutting existing steel tubing for alterations or additions (each cut measured) for 40/50mm, complete all as specified and directed. |
| 165 | S & F storage water heater (geyser) 5 star rated as per BEE norms electrically operated suitable for 230 volts, 50 hz, AC supply system complete with glass coated insulated heating element tank of capacity 25 litre, complete with all accessories such as safety valve, thermostat, NRV,connecting hose-02 Nos hot and cold water, complete all as specified & directed. |
| 166 | M & L for submain wiring with single core PVC insulated but unsheathed FRLS cable of size 2 Run of 4 sq mm cable and one Run of 4 sq mm earth continuity conductor of similar type cable multistranded copper conductor 1100 volts grade IS:694 marked drawn in and inluding 25mm dia PVC casing caping/ pipe , medium grade, ISI marked complete with all acessories and fittings all laid in ceiling or surface ,walls and also include the specified runs of cablescomplete all as specified & directed.Note:- 2 Run of main cable, one run of earth continuity conductor & one run of PVC casing capping/pipe shall be measured as one Run. |
| 167 | Supply & Fixing of PVC box suitable for fixing of modular cover plate 3 modules complete all as specified & directed. |
| 168 | Supply & Fixing Modular Cover plate 3 Module suitable for fixing of switches and sockets, complete all as specified & directed. |
| 169 | Supply & Laying of 80 mm bore galvanised steel water tubing, medium grade laid in tranches/ wall/ floor / on ground and joined including necessary fittings such as bends, flanges elbow, tees sockets, etc including necessary saddles and clamps, complete all as specified and directed. |
| 170 | Supply & Laying of 100 mm bore galvanised steel water tubing, medium grade laid in tranches/wall/floor/on ground and joined including necessary fittings such as bends, flanges elbow, tees sockets , etc including necessary saddles and clamps including taking down old UNSV GI pipes, complete all as specified and directed. |
| 171 | Supply & Laying of 50 mm bore galvanised steel water tubing, medium grade laid in tranches/wall/floor/on ground and joined including necessary fittings such as bends, elbow, tees sockets etc including necessary saddles and clamps including taking down old UNSV GI pipes, complete all as specified and directed. |
| 172 | Supply & Laying of 40 mm bore galvanised steel water tubing, medium grade laid in tranches/wall/floor/on ground and joined including necessary fittings such as bends, elbow, tees sockets etc including necessary saddles and clamps including taking down old UNSV GI pipes, complete all as specified and directed. |
| 173 | Material and labour for cutting, drilling and taping cast iron / Ductile iron/ GI water mains (in position) for branch connection of the outer dia 80 to 150 mm including necessary fittings such as ferrules, nipple short pipe etc, complete all as specified & directed. |
| 174 | Supply and fix Valves, Sluice, flanged of class 1.0 PN, 150 mm (6”)dia complete with nut, bolt, washer and packing including taking down the old UNSV valve, complete all as specified & directed. |
| 175 | Supply and fix Valves, Sluice, flanged of class 1.0 PN, 100 mm (4”) dia complete with nut, bolt, washer and packing including taking down the old UNSV valve, complete all as specified & directed. |
| 176 | Supply and fix Valves, Sluice, flanged of class 1.0 PN, 80 mm (3”) dia complete with nut, bolt, washer and packing, complete all as specified & directed. |
| 177 | M&L for construction of brick masonarry new valve pit chamber of size 900mm x 900mm x 900mm (internal size) 100mm thick PCC 1:4:8 type D2 lean concrete foundation using 40mm graded stone aggregate providing well burnt brick masonary wall of 23mm thick built in CM 1:6 rendering in cement mortar 1:6 finished even & smooth using extra cement internally and 20mm thick in CM 1:4 and finished fair and even supply and fix 3 mm thick MS sheet steel cover fixed on 50mmx50mmx4mm thick angle iron frame embbeded in PCC coping with locking arrangement and 1 Nos 50mm size 4 levers lock with key in duplicate Standard size and MS hold fast and handle made out of 25 x 6mm flat iron appplying two coats of synthetic enamel paint of approved shade over a coat of primer (Red Oxide) to all exposed steel surface making good all disturbed surface to match surrounding, complete all as specified & directed. |
| 178 | M&L for construction of brick masonarry new valve pit chamber of size 1200mm x 1200mm x 1200mm (internal size) 100mm thick PCC 1:4:8 type D2 lean concrete foundation using 40mm graded stone aggregate providing well burnt brick masonary wall of 23mm thick built in CM 1:6 rendering in cement mortar 1:6 finished even & smooth using extra cement internally and 20mm thick in CM 1:4 and finished fair and even supply and fix 3 mm thick MS sheet steel cover fixed on 50mmx50mmx4mm thick angle iron frame embbeded in PCC coping with locking arrangement and 1 Nos 50mm size 4 levers lock with key in duplicate Standard size and MS hold fast and handle made out of 25 x 6mm flat iron appplying two coats of synthetic enamel paint of approved shade over a coat of primer (Red Oxide) to all exposed steel surface making good all disturbed surface to match surrounding, complete all as specified & directed. |
| 179 | Supply Fabrication and errection structural steel work made out of angle iron channels flats sheets etc by rivited bolted or welded in built up section trusses in and including cutting hoisting fixing in position and applying two coats of weather proof synthetic Enamel Paint over a coat of red oxide primer (anti corrossive primer) of approved colour suitable for base platform of 50000 Ltr capacity SMC Tank, complete all as specified & directed. |
| 180 | Supply and Fixing of sintex SMC panel tank Cap 50000 Ltr square type , made out of HOT PRESS MOULDED SHEET MOULDING COMPOUND panels of size 5 M X 5M X 2 M the flange shall be perpendicular to the main surface. The shape shall be Trunked type of extra strength and 90 degree flanges pre drilled for bolting. All the flanges of the 1 Mtr panel should have 13 Nos holes per side for fastening/jointing the panels to one another .Hot Pressed Moulded SMC Pre Drilled corner pieces with built -in ribsof the size 75 mm X 75 mm shall be provided for 90 degree joints of tank wall to roof joints complete with olive green nuts ,bolts and washers Special Sealent having excellent UV resistance as well as suitable for potable water ,must be ISI marked meeting BIS14399 ( part 1 & 2) .Tank inlet and outlet size 80 mm dia for connection of GI pipe, complete all as specified & directed (Make :- Amitex / Sintex or Eqivalent or equivalent make as approved by GE). |
| 181 | M & L Gun metal globe/gate valve (ISI Marked) with iron wheel head, screwed both ends for pipes or for unions for 50 mm bore dia steel tubing, complete all as specified & directed. |
| 182 | M & L Gun metal globe/gate valve (ISI Marked) with iron wheel head, screwed both ends for pipes or for unions for 40 mm bore dia steel tubing, complete all as specified & directed. |
| 183 | M&L for plain cement 1:3:6 type C-1 (using 40mm graded stone aggregate) in foundation of PCC Poles/ struts including necessary formwork, complete all as specified and directed Please Enable Macros to View BoQ information |
