|
| 1 | Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per specification and direction of E/I |
| 2 | Providing 6mm. cement plaster (1:4) in ceiling with clean coarse sand of F.M 1.5 including cost of carriage, screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. |
| 3 | Providing 12mm. cement plaster (1:6) with clean coarse sand of F.M. 1.5 including cost of carriage, screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. |
| 4 | Dismantling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 5 | Covering of treated surface with PCC :- Providing 50 mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm |
| 6 | Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 7 | Supplying and fixing 10 Gauge weld mesh of size 100mm x 100 mm for floor/roof slab concrete screed over the micro beams as reinforcement. The weld mesh shall be fixed as per drawing. |
| 8 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : |
| 9 | Dismantling patent stone floor including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 10 | Providing 25mm thick first class patent stone flooring (1:2:4) with stone chips in two layers, bottom layers 19mm. Thick (1:2:4)with 12mm to 6mm. Size graded stone chips and top layer 6mm. Thicks (1:2) with 6mm down stone chips, in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royality with all complete as per building specification and direction of E/I. |
| 11 | For StairProviding and laying vitrified floor tiles for step of stair in with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete step tiles & have bullnose, Anti and self embossed line. Size of Tile 1200x300 mmx15 mm |
| 12 | Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) |
| 13 | Providing and laying 6mm. precast white glazed tiles in walls over 12mm. cement mortar (1:3) and jointed with grey cement slurry, finish pointed with white cement including rubbing, polishing and cost of curing, taxes and royalty all complete as per Building specifications and direction of E/I With commercial grade white 15x15cm tiles. |
| 14 | Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 15 | Providing two coats of oil bound distemper of approved shade and make over old surface includingwashing cleaning and papering the walls, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/I. |
| 16 | Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqmover and including priming coat of exterior primer applied@ 2.20 kg/10 sqm) |
| 17 | Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thououghly, scaffolding and taxes all complete as per building specifications and direction of E/I |
| 18 | Supplying, fitting and fixing fully glazed steel door, window or ventilations of standard rolled 'Z' and mullion steel sections and size as per IS-1038 joints met and welded with 100X16X3mm M.S. lugs fixed in cement concrete (1:2:4) block 15X10X10cm, size including cost of oxidised iron fittings, with hinges, handle per steps, catch springs, 3mm thick plain glass panes with Aluminimum beads and inner frame fixed with lugs with 20mm long 6.3mm G.I. counter sunk machine screw and nuts and applying a coat of red lead paint carriage to work site hoisting and placing in position in all storys and taxes all complete as per building specification and direction of E/I. |
| 19 | Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.) |
| 20 | Supplying fitting and fixing glass panes including supplying putty. Beads and nails after taking out old and broken glass panes and disposal of debris all complete as per building specification and direction of E/I.3mm plain |
| 21 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 22 | Supplying, fitting and fixing vitreous white glazed earthenware I.W.C of Parry, Hindustan or any other I.S.S approved make with 100 mm H.C.I 'P' trap, 15 litres (high level) C.I pull and let go flushings cistern- liter low down C.I mosquito Proof flushing cistern of Nomus or other I.S.S equivalent make, Complete with all fittings, C.I or R.S bracket, 32 mm alkathene/ P.V.C telescopic flush pipe about 2 meter long with one brass coupling and clamps. C.I chain and pull including supplying and fixing a pair of vitreous white glazed earthen ware foot rest to be fixed in floor 15 mm C.I body brass spindle stop cock of weight not less than 50 gms, 15mm P.V.C connection pipe 450 mm long and than 15 mm P.V.C connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I (B)510mm long With 10 litre low level P.V.C. cistern |
| 23 | Supplying fitting and fixing flat back or angujlar type vitrious urinal as per do--do-- E/I |
| 24 | Supplying, fitting and fixing 550mmx400x400mm size vitreous white glazed earthan ware ware wash hand basin of ‘Parry’ or Hindustan or any other I.S.S approved make supported on painted C.I or R.S brackets 32mm C.P brass spindle stop cock of approved quality of weigth not less than 450 gms. 15mm P.V.C pipe 450 mm long with brass coupling 15mm dia C.P Brass pillar cock of approved quality weight not less than 350 gms 32 mm P.V.C waste pipe 750 mm long with brass coupling at noe end and making plumber joint etc. all complete as per specifications and direction of E/I |
| 25 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 26 | 75 mm Dia |
| 27 | 110 mm Dia |
| 28 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 29 | Single tee with door 75x75x75 mm |
| 30 | Single tee with door 110x110x110 mm |
| 31 | Bend 87.5° 75 mm bend |
| 32 | Bend 87.5 110 mm bend |
| 33 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. |
| 34 | 15 mm nominal dia Pipes |
| 35 | 20 mm nominal dia Pipes |
| 36 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. |
| 37 | 25 mm nominal dia Pipe |
| 38 | 32 mm nominal dia Pipes |
| 39 | Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750mm deep 600x450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:0 with 600x475mm G.I cover with frame (weight not less than 36kg) along with earth work in excavation and 80mm thick P.C.C (1:3:6) in foundation and refilling all complete as per specification and of E/I |
| 40 | Providing and fixing male ended 15mm dia brass bib cock of approved quality (Wt not less than 350 gms)with extra socket all complete as per specifications and direction of E/I |
| 41 | Providing and fixing brass/C.I stop cock of approved quality all complete as per specifications and direction of E/I (A) BRASS STOP COCK 15mm dia |
| 42 | Providing and fixing 15mm size C.P. brass pillar cock (weight not less than 350gms C.I body brass spindle pillar cock of approved quality all complete as per specifications and direction of E/I C.I. body brass spindle |
| 43 | Wiring for Circuit/submain wiring along with earth wire with the following sizes PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required. |
| 44 | (i) 2 x1.5sq.mm. + 1 x1.5sq.mm. earth wire |
| 45 | (ii) 2 x 2.5 sq.mm. + 1 x 2.5 sq.mm. earth wire |
| 46 | S/F Modular Boxes, base & cover plate: Supplying and fixing following size / modules GI box along with modular base & cover plate for modular switches in recess etc as required. 12 Module (135mm x 205 mm x 60 mm) |
| 47 | S/F Ceiling Rose: Supplying and fixing 2 pin 5 amp ceiling rose on the existing junction box/ wooen block including connection etc as required. Make :- Anchor / Kona / Kany |
| 48 | S/F Batten / Angle Holder: Supplying and fixing batten / angle holder including connection etc as required. |
| 49 | S/F S.P MCB DB :- Supplying and fixing following way, single pole and neutral sheet steel MCB distribution board 240 Volts on surface/recess, complete with tinned copper bus bar neutral bus bar, earth bar, din bar including powder Painted including earthing etc as required. (But without MCB/RCCB/ Isolator) 8 way single door |
| 50 | Suppling Instalation festing and commissioning of following size celling fan 3 blades confirming to IS : 374:2019 including wiring the down roads of standard lenth (up to 30 cm) with 1.5 sqmm FR PVC insulated copper wire suitable for 230v 50 HZW, single phase supply etc complete as required. 1400mm (56'') ceiling fan. |
| 51 | S/F 10/12 watt LED Tube Light |
| 52 | Suppling and fitting 15/16Watt LED Bulb |
| 53 | S/F Modular type switch/Socket :- Supplying and fixing of following modular switch/Soket on the existing modular plate & switch box including connections but encluding modular plate etc as required. |
| 54 | 5/6 amps one way Switch |
| 55 | 5/6 amps 3 Pin Socket ourt let |
| 56 | Carriage of materials |
| 57 | stone chips |
| 58 | Provision of GST @18% |
| 59 | Add 1% Labour Cess Please Enable Macros to View BoQ information |
