|
| 1 | Clearing jungle including up rooting of trunk vegetation grass bush wood trees and sapling of girth upto 30cm. Measured at a height of 1 meter above ground level and removal of rubbish upto a distance of 50m. outside the periphery of area cleared as per DSR SI NO. 2.31 |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil as per DSR SI.No. 2.8.1 |
| 3 | Diluting and injecting chemical emulsion for anti-termite treatment (excluding the cost of chemical emulsion) Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration as per SI.No.SOR 19.03 |
| 4 | Excavating, supplying and filling of local earth by mechanical transport upto a lead of 8.0km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. (Under Floor) as per SI.No. 301.5 |
| 5 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. as per DSR SI no 2.27 |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) As per DSR SI no. 4.1.8 |
| 7 | Brick work with common burnt clay (non modular) bricks of class -150 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand) as per DSR SI No- 6.1.1 |
| 8 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete woek - All work up to plinth level concrete of M-25 grade with minimum cement content of 330kg/cum as per DSR SI No-5.33.1.1 |
| 9 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete woek - All work up to plinth level concrete of M-25 grade with minimum cement content of 330kg/cum as per DSR SI No-5.33.1.1 |
| 10 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete woek - All work Above plinth level concrete of M-25 grade with minimum cement content of 330kg/cum as per DSR SI No-5.33.2.1 |
| 11 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete woek - All work up to plinth level concrete of M-25 grade with minimum cement content of 330kg/cum as per DSR SI No-5.33.1.1 |
| 12 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete woek - All work Above plinth level concrete of M-25 grade with minimum cement content of 330kg/cum as per DSR SI No-5.33.2.1 |
| 13 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete woek - All work Above plinth level concrete of M-25 grade with minimum cement content of 330kg/cum as per DSR SI No-5.33.2.1 |
| 14 | Steel reinforcement for R.C.C. work ready to use \\"cut and bend\\" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete in Thermo-Mechanically Treated bars of grade Fe-500D or more. As per DSR SI. No.- 5.22 B.1 |
| 15 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. as per SI-4.13 |
| 16 | Brick work with common burnt clay bricks of M-150 Class in super structure above plinth level upto floor V level in all shapes and sizes in cement mortar 1:4 ( 1 cement : 4 coarse sand ) as per DSR SI no 6.4.1 |
| 17 | Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. In grantings, frames, guard bar, ladder, railing, brackets, gates and similar works as per DSR SI no. 10.25.2 |
| 18 | Providing and fixing M.S Tublar frames for doors,windows,ventilators and cupboard with rectangular/ L-type sections,made of 1.6mm thick required size, including fixing of necessary butt hinges and screws and apply a priming coat of approved steel primer. as per DSR SI no. 10.15.1 |
| 19 | Providing and fixing of acoustic door with chowkhat for door opening size 1.50 x 2.40M providing supply, installation ,tedting and fixing in position a 65mm thick acoustic door with chowkhat. Door should have a 150mmx300mm vision panel of 6.0mm thick toughened glass. Both shutters shall be made with 100mm x50mm thick hardwood outer frame with 50mm x50mm hardwood ribs at 500mm c/c bothways. allwoodwork shall be treated with anti-termite treatment. the door shutter shall have 6mm thick bwp grade plywood fixed on its both sides. all the cavities inside the door shall be filled with high NRC acoustic insulation materials (rockwookof 60kg/m3 density) insides of the door will be lined with 3mm thick MLV sheet of minimum 1700kg/m3 density. periphery of the shutter shall be covered with 12mm thick teakwood lipping matching with the door frame. the external faces of the door shutter will be finished with 1mm thick laminate on both sides. teakwood lipping will be melamine polished. weather seal of rehau make shall be fixed on the door frame to fill the gap of shutter and wooden frame .drop down seal to be fixed in shutter to block the gap with floor when the door is closed . the coast shall include all hardware fitting like heavy duty ss hings (4inchlong -5per door, 1ft long D TYPE SS 304 Handles of godrej/ hettich/dorma make (both inside and outside _ |
| 20 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- decorative type, core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary. Extra for cutting rebate in flush door shutters as per DSR SI No- 9.21.2 |
| 21 | Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge Door Chaukhat as per SI- 14.2.1 |
| 22 | Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge Window Chaukhat as per DSR SI No- 14.2.2 |
| 23 | Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge Vent. Chaukhat as per DSR SI No- 14.2.3 |
| 24 | Providing and fixing glass panes with putty and glazing clips in steel doors, windows, clerestory, all complete with 4.0 mm thick glass panes. As per DSR IS No - 10.30.1 |
| 25 | 15 mm thick cement plaster of mix 1:6 ( 1 cement & 6 course sand ) Inner Side as per DSR IS No- 13.5.2 |
| 26 | 12 mm thick cement plaster of mix 1:6 ( 1 cement & 6 course sand ) Outer Side as per DSR IS No- 13.4.2 |
| 27 | 15 mm thick cement plaster of mix 1:4 ( 1 cement & 4 coarse sand )Below Plinth as per DSR IS No- 13.5.1 |
| 28 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone ) finished with floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. 40 mm thick floor 20 mm nominal size stone aggregate. as per DSR SI No- 11.3.1 |
| 29 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : (25 mm thick). As per DSR SI No-11.26 |
| 30 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing omplete. as per DSR SI No-11.27 |
| 31 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm as per DSR SI no 11.41.2 |
| 32 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Light shade pigment using white cement as per DSR SI No-11.20.1 |
| 33 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture as per DSR Sl no. -13.62.1 |
| 34 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre as per DSR Sl no. -13.41.1 Two Coats |
| 35 | Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) as per DSR Sl no. -13.46.1 Two Coats |
| 36 | Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer,over the plasterd wall surface even and smooth surface as per DSR Sl no. -13.80 |
| 37 | Providing and fixing glass strips in joints of terrazzo/ cement concrete floors. 40 mm wide and 4 mm thick. As per DSR SI No- 11.13.1 |
| 38 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs,balconies,terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS.2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.b)Laying bricks bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5(1 cement:5 coarse sand) admixed with water proofing compound conforming to IS:2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS:2645 and approved by Engineer-in-Charge to required slope and trating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS:2645 and approved by Engineer-in-Charge.d)Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand) admixed with water. as per DSR SI No- 22.5 |
| 39 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378) . (a) 250mm x 16mm. as per DSR SI.No- 9.62.1 |
| 40 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378) 250mm x 10mm. as per DSR SI No- 9.63.1 |
| 41 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378) (a) 125 mm. as per DSR No- 9.66.1 |
| 42 | Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete. As per DSR SI No- 14.34 |
| 43 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes.100 mm diameter. As per SOR 2025 15.(IV) |
| 44 | Centering and shuttering including stutting, propping etc. and removal of form. Foundation as per DSR SI No- 5.9.1 |
| 45 | Centering and shuttering including stutting, propping etc. and removal of form. Columns, pillars as per DSR SI No - 5.9.6 |
| 46 | Centering and shuttering including stutting, propping etc. and removal of form. Beam /Band as per DSR SI No- 5.9.5 |
| 47 | Centering and shuttering including stutting, propping etc. and removal of form. Slab as per DSR SI No - 5.9.3 |
| 48 | Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fiber and natural filler false ceiling tiles of size 595x595mm of approved texture, design and patterns having NRC (Noise reduction coefficient ) of 0.50 (minimum) with 15mm thick integral densified micro edge light weight calcium silicate false ceiling tiles......as per DSR SI No- 26.23.1 |
| 49 | Providing & fixing in position wall panelling at all heights with integral densified calcium silicate /tiles of size 595x595mm, having NRC (Noise reduction coefficient ) of 0.50 (minimum) as per is 8225:1987, light reflectance of 85%(minimum ) with 15mm thick fully perforated square/ butt edge light weight calcium silicate panels/ tiles .....as per DSR SI No- no 26.24.1 |
| 50 | Providing & fixing in position phenol bonded bamboo wood flooring with planks of sizes 14mm thick, minimum 1800mm length and minium 100 mm wide , in approved colour , texture and finish, having performance appraisal certificate (PAC) issued by building materials &technology promotion council (BMTPC ). .....as per DSR SI No- 26.1 |
| 51 | Providing & fixing OF Auditorium seat sliding and push back from 23inch, arm rest handle with cup holder .....as per direction of Engineer -in - charge |
| 52 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.dsr no 1.10.1 |
| 53 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire dsr no 1.14.1 |
| 54 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire dsr no 1.14.2 |
| 55 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 4 sq. mm + 2 X 4 sq. mm earth wire dsr no. 1.14.8 |
| 56 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 10 sq. mm + 2 X 6 sq. mm earth wire. Dsr no 1.14.10 |
| 57 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. Dsr no 1.31 |
| 58 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. dsr no 1.32 |
| 59 | Supply and fixing of panel light 2x2 fit of following body material and construction as per SI: 10322 fitting suitable for up to 45 watt light on surface complete in all respect. - dsr no .8.7.6 |
| 60 | Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 36 watt LED tube light on surface complete in all respect. dsr no.8.9.7 |
| 61 | Supply and fixing of recess/Surface/Pendent mounting round 12 Watt to 15Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect dsr no 8.2.3 |
| 62 | Supply and fixing of recess/ Surface/ Pendent mounting round 8 to 10 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. Dsr no 8.3.2 |
| 63 | Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 90 Watt. Confirming to IP 66 protection complete in all respect. Dsr no 8.14.14 |
| 64 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00,Air deliveryminimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase ACSupply, earthing etc. complete as required. dsr no 9.1.3 |
| 65 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. Dsr no 1.25 |
| 66 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep, dsr no 1.50.1 |
| 67 | Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes, dsr no 1.51 |
| 68 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. 4 way (4 + 12), Double door dsr no 2.5.1 |
| 69 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. 8 way (4 + 24), Double door dsr no 2.5.2 |
| 70 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole dsr no 2.10.3 |
| 71 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Sengle pole dsr no 2.10.1 |
| 72 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. Dsr no 2.11 |
| 73 | Supplying and fixing following capacity TP&N 160A disconnector fuse switch unit inside the existing board as required dsr no 2.1.5 |
| 74 | Supplying and fixing following capacity TP&N 400A disconnector fuse switch unit inside the existing board as required dsr no 2.1.8 |
| 75 | Supply and laying of aluminium conducter, PVC insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the cable run shall be fixed on M.S. clamps etc. of suitable size. or as directed by the Engineer-Incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. 50 sq. mm 3-1/2 core (UPPWD 501 (L) |
| 76 | Supply and burring of Safe Earthing pipe 4.5m long ,40mm dia including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.with charcoal/ coke and sait as required…all complete. Dsr no 5.2 |
| 77 | Supplying & Laying of 25mmx5mm G.I. Strip for earthing purpose as required complete in all respects. Dsr no 5.9 |
| 78 | Supply and Fixing of Fire Extinguisher ABC Type 6.0 kg. Capacity ( ISI Market IS : 15683 & TAC approved ) complete with initial charge and wall bracket, along with supply of all materials and labour for propercompletion(Firiecon/LifeGurd/Firefit/Excell) (lko pwdsor 1131 ) |
| 79 | Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. (lko pwdsor 1132 ) |
| 80 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. (a) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests dsr no 17.1.1 |
| 81 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require . (a) White Vitreous China Flat back wash basin size 550 x 400 mm with single 15 mm C.P. brass pillar tap. dsr no 17.7.4 |
| 82 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. Semi rigid pipe (a) 32mm dia dsr no 17.28.1.1 |
| 83 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms. Dsr no 18.65 |
| 84 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge. Dsr no 17.16a |
| 85 | Providing and fixing C.P brass shower rose with 15 or 20mm inlet 150mm dia . good quality and make as approved by Engineer - in -charge.dsr no 18.22.2 |
| 86 | Providing and fixing 600x450mm beveled edge mirror of superior glass complete with 6mm thick hard board ground fixed to wooden cleats make as approved by Engineer - in -charge. Dsr no 17.31 |
| 87 | Providing & fixing PVC pipes conforming to IS make working pressure 6 Kg/cm² including testing, labour, T&P and all complete fittings. 100mm dia (UPPWD SORCH-2ITEM -15 (IV ) bsr |
| 88 | Providing & fixing PVC pipes conforming to IS make working pressure 6 Kg/cm² including testing, labour, T&P and all complete fittings. 75mm dia (UPPWD SOR CH-2 ITEM -15 bsr |
| 89 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall 32mm dia nominal dia pipes. dsr no 18.7.4 |
| 90 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. 20mm dia nominal dia pipes dsr no 18.8.2 |
| 91 | Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions. (a) 15mm nominal bore. Dsr no 18.21.2.1 |
| 92 | Providing & fixing CP brass bib cock of approved quality conforming to IS 8931 (a) 15mm nominal bore dsr no. 18.49.1 |
| 93 | Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931 (a) 15mm nominal bore. Dsr no 18.53.1 |
| 94 | Providing and fixing gun metal gate valve with wheel of approved quality. (d) 32mm dia nominal bore. Dsr no 18.17.2 |
| 95 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. dsr no 18.48 |
| 96 | Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m. (a) Pipes 80mm to 300mm diameter.dsr no 2.10.1.2 |
| 97 | Providing, laying and joining glazed stone ware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. (b) 150mm diameter. Dsr no 19.1.2 |
| 98 | Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design. (b) 150mm diameter S.W. Pipe. Dsr no 19.2.2 |
| 99 | Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). With FPS bricks of class designation 7.5 (i) For Sewer Line. dsr no 19.7.1.1 Please Enable Macros to View BoQ information |
