|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. DSR No. 2.6.1 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 2 | Banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m : DSR No. 2.3.1 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) DSR-4.1.8 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1.5:3 (1 Cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) DSR-5.1.2 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 5 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level concrete of M25 grade with minimum cement content of 330 Kg/cum DSR-5.33.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 6 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works above plinth level upto floor V level DSR-5.33.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 7 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. DSR 5.22.A.6 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform DSR 5.9.3 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 9 | Shelves (Cast in situ) DSR 5.9.4 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 10 | Lintels, beams, plinth beams, girders, bressumers and cantilevers DSR 5.9.5 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 11 | Weather shade, Chajjas, corbels etc., including edges DSR 5.9.19 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 12 | Edges of slabs and breaks in floors and walls Under 20 cm wide DSR 5.9.16.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 13 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) DSR 6.1.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 14 | Brick work with common burnt clay machine moulded F.P.S. (non modular) bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand).From ground level upto plinth level DSR 6.29.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 15 | Brick work with common burnt clay machine moulded F.P.S. (non modular) bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). Above plinth level upto floor V level DSR 6.29.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 16 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) DSR 6.4.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 17 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) DSR 6.13.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 18 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. DSR 6.15 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 19 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. DSR 4.13 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 20 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) DSR 4.10 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 21 | Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. DSR 10.31 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 22 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding DSR 9.48.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 23 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws DSR 9.21.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 24 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). DSR 9.23 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 25 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides DSR 10.29.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 26 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes DSR 10.30.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 27 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm DSR 10.62.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 28 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish,(Barrel type) with necessary screws etc. complete : 250x10 mm DSR 9.63.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 29 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish,(Barrel type) with necessary screws etc. complete : 200x10 mm DSR 9.63.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 30 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm DSR 9.66.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 31 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper DSR 9.101.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 32 | Providing and fixing to existing door frames.30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. DSR 9.122.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 33 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.(The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.) DSR 22.5 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 34 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) DSR 13.4.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 35 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand) DSR 13.5.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 36 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate DSR 11.3.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 37 | Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick DSR 11.6.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 38 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. DSR 11.37 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 39 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. DSR 11.37A & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 40 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. DSR 4.17 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 41 | Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick DSR 11.13.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 42 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer DSR 13.41.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 43 | Fininshing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @1.67 ltr/10 sqm over and including priming coat of exterior pimer applied @0.90 liter/10 sqm) DSR 13.46.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 44 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR 13.80 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 45 | Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works DSR 10.25.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 46 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture DSR 13.48.3 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 47 | Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks: 1:6 (1cement : 6 coarse sand) DSR 11.1.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 48 | Providing and fixing magnetic catcher of approved quality in cupboard /ward robe shutters, including fixing with necessary screws etc. complete. Double strip (horizontal type) DSR 9.114.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 49 | Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge DSR 9.129 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 50 | Providing and fixing special quality bright finished brass cupboard orward robe locks with four levers of approved quality including necessaryscrews etc. complete. 65 mm DSR 9.79.3 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 51 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). DSR 10.13.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 52 | Providing and fixing chromium plated brass handles with necessaryscrews etc. complete: 125 mm DSR 9.92.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 53 | Making soak pit 2.5 m dia meter 3.0 meter deep with 45x45 cm dry brick honey comp s.w drain pipe 100 mm diameter 1.8 m long complete as per standard design with f.p.s. brick as per DSR NO 19.32.1 including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 54 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. DSR 10.3 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 55 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should besupplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. DSR 12.50 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 56 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes DSR 10.16.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 57 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Flashings/Aprons (up to 600 mm) 12.51.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 58 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Gutter (600 mm over all girth) 12.51.6 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 59 | SANITARY INSTALLATIONS & FITTINGSProviding and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests DSR 17.1.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 60 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid DSR 17.2.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 61 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 62 | Providing and fixing toilet paper holder : Vitreous china DSR 17.34.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 63 | Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not less than 88 gms DSR 18.54.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 64 | Providing and fixing wash basin with C.I. brackets, 15 mm PTMT pillar cock, 32 mm PTMT waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm PTMT pillar cock. DSR 17.7B & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 65 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. DSR 17.31 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 66 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. DSR 17.71 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 67 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. DSR 17.73 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 68 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern DSR 17.4.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 69 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore DSR 18.52.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 70 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 470x420 mm bowl depth 178 mm DSR 17.10.3 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 71 | Providing and fixing PTMT pillar cock of approved quality and colour. 15 mm nomina DSR 18.56.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 72 | Providing and fixing PTMT stop cock of approved quality and colour. Concealed stop cock, 15 mm nominal bore, 108 mm long, weighing not less than 108 gms DSR 18.55.3 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 73 | Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore DSR 18.21.2.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 74 | Providing and fixing PTMT bib cock of approved quality and colour. 15 mm nominal bore, 165 mm long, weighing not less than 110 gms DSR 18.54.3 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 75 | Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia DSR 18.58.1.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 76 | INTERNAL SOIL, WASTE & RAIN WATER ORAINAGE SYSTEMProviding and fixing P.V.C. waste pipe for sink or wash basin includingP.V.C. waste fittings complete. 32 mm dia DSR 17.28.2.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 77 | Providing and fixing P.V.C. waste pipe for sink or wash basin includingP.V.C. waste fittings complete. 40 mm dia DSR 17.28.2.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 78 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet DSR 17.60.1.3 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 79 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter DSR 12.41.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 80 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter DSR 12.41.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 81 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. |
| 82 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler DSR 12.42.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 83 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 75 mm DSR 12.42.1.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 84 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° DSR 12.42.5 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 85 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm Bend DSR 12.42.5.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 86 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 75mm Shoe DSR 12.42.6.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 87 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm Shoe DSR 12.42.6.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 88 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm DSR 12.43.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 89 | INTERNATION WATER SUPPLY SYSTEMProviding and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes DSR 18.8.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 90 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes DSR 18.8.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 91 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work-Exposed on wall 20 mm nominal outer dia Pipes DSR 18.7.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 92 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work-Exposed on wall 25 mm nominal outer dia Pipes DSR 18.7.3 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 93 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work-Exposed on wall 32 mm nominal outer dia Pipes DSR 18.7.4 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 94 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 20 mm nominal outer dia Pipes DSR 18.9.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 95 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal outer dia Pipes DSR 18.9.3 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 96 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore DSR 18.17.1A & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 97 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore DSR 18.17.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 98 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore DSR 18.17.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 99 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. DSR 18.48 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 100 | EXTERNAL SEWERAGE & RAIN WATER DRAINAGE SYSTEMExcavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia DSR 2.10.1.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 101 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150MM DIA RCC Pipes DSR 19.6.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 102 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 150MM DIA RCC Pipes DSR 19.3.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 103 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type 19.4.2.2 With sewer bricks conforming to IS : 4885 DSR 19.4.2.2 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 104 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floatingcoat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : DSR 19.7.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 105 | Extra for depth for manholes : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.8.1.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 106 | Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar DSR 19.15.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. |
| 107 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.27.1 & including cost of all material, labour, T&P, labour cess, Royalty, ISTP and all other taxes but excluding G.S.T. Please Enable Macros to View BoQ information |
