|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 2 | 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 3 | 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 4 | Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete (Copper oxidised as per IS 1378) |
| 5 | 300 mm weighing not less than 330 grams |
| 6 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. |
| 7 | Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, priming coat of approved steel primer, but excluding the cost of other fittings, glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment). |
| 8 | Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 9 | Welding by gas or electric plant including transportation of plant at site etc. complete. |
| 10 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 11 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 12 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. |
| 13 | G.I. pipes |
| 14 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with : |
| 15 | 4.0 mm thick glass panes. |
| 16 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 17 | 40 mm thick with 20 mm nominal size stone aggregate |
| 18 | 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 19 | Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. |
| 20 | 18 mm thick. |
| 21 | Chequerred precast cement concrete tiles 22 mm thick in footpath &courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). |
| 22 | Dark shade pigment using ordinary cement. |
| 23 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i)Single socketed pipes. |
| 24 | 160 mm outer diameter |
| 25 | Providing and fixing on wall unplasticised rigid PVC drainage pipe for wash basin, sink, urinal etc. including uPVC fittings, jointing with solvent cement etc. complete as per direction of the Engineer-in-charge. |
| 26 | 50 mm nominal dia off white shedule: 40 pipe. |
| 27 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. |
| 28 | (a) Single tee without door (i) 160x160x160 mm |
| 29 | (b) Bend 87.5° (i) 160 mm bend |
| 30 | © Shoe (i) 160 mm Shoe |
| 31 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 32 | 110 mm |
| 33 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hardwood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 34 | 160mm dia MS clamp for SCI or PVC pipe |
| 35 | Providing and fixing Mild Steel pipe clamps of approved design to unplasticised - PVC rain water pipes or S.C.I pipe by means of fasters or 50x50x50mm hardwood plugs, screwed with M. S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 36 | MS clamp for 100mm nominal dia SCI or PVC pipe |
| 37 | MS clamp for 160mm dia SCI or PVC pipe |
| 38 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /seIf tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 39 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : |
| 40 | Ridges plain (500 - 600mm) |
| 41 | Gutter (600 mm over all girth) |
| 42 | 12 mm cement plaster of mix : |
| 43 | 1:6 (1 cement: 6 coarse sand) |
| 44 | 15 mm cement plaster on rough side of single or half brick wall of mix : |
| 45 | 1:6 (1 cement: 6 coarse sand) |
| 46 | Neat cement punning |
| 47 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. |
| 48 | Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. |
| 49 | Applying priming coat : |
| 50 | With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works |
| 51 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 52 | Two or more coats on new work. |
| 53 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 54 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : |
| 55 | Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface. |
| 56 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-harge. |
| 57 | With cement mortar 1:4 (1cement: 4 coarse sand). |
| 58 | Cleaning and de-silting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge. |
| 59 | Cleaning of under ground sump, Over Head R.C.C. Tank (independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:- (i) Tank shall be emptied of water by pumping & bottom shall be cleaned of slit and other deposits. (ii Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. (iii) Chlorination of RCC internal surface by liquid chlorine.(iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge. |
| 60 | Renewing two point steel (oxidised) handle of steel doors and windows as directed including painting complete. |
| 61 | Labour charges for for repairing to steel window, renewing damaged steel window members, MS grill etc. by cutting steel members including taking out and refixing, adjusting, welding, cleaning, cutting holes, scrapping all members and fitting so as to make the shutter easily operable, mending good damages to match existing one [Note: 1. Cost of MS member renewed to window, MS grill, new window hinge, handle, stays etc., will be paid seperately 2. Cost includes for making necessary scaffording and shifting of scaffolding etc. 3. Cost includes dismantling and refixing of glass panes where necessary.] a) For single or double shutter window up to 15m height. |
| 62 | Supplying of M.S steel window members for renewing damaged members of steel to make the shutter operable as per direction of the Engineer. |
| 63 | Supplying of Steel for repair works work welded in built up sections/ framed work, as required. |
| 64 | Renewing hinge of steel shutter including taking out old one by cutting and fixing new hinges by welding and mending good complete. |
| 65 | Refixing available iron materials for cable tary, ladder, grills, frame works, cable duct cover including applying a coat of with ready mixed red oxide zinc chromate primer as per direction of the Engineer-in-charge. |
| 66 | Removing loose scales, blisters etc. from old painted surface and thoroughly smoothening the surface to make the same suitable for receiving fresh coat of paint as per direction of the Engineer-in-charge. |
| 67 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 68 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 69 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 70 | Of area beyond 3 sq. metres |
| 71 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 72 | For thickness of tiles 10 mm to 25 mm |
| 73 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: |
| 74 | G.S. Sheet |
| 75 | Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead : |
| 76 | 100 mm dia pipe |
| 77 | 150 mm dia pipe |
| 78 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 79 | Dismantling GI/PVC pipe with fittings and clamps including stacking within the compound as per direction of the Engineer -in Charge. |
| 80 | 15mm to 50 mm diametre pipe. |
| 81 | Dismantling fixtures where necessary as per direction of the Engineer-in-Charge. |
| 82 | Flushing cistern, wash basin, sink, EWC , Anglo Indian WC etc. |
| 83 | CP/ Brass/ PTMT/PVC/Iron stop cock/ bib cock/ pillar cock/ wheel valve/gate valve etc. upto 50mm dia. |
| 84 | Supplying of ISI marked G.I. fittings for G.I. water pipe line work of required length and diameter. |
| 85 | (a) Equal or reducing Socket, Elbow, Tee etc. (i) 15 mm dia & 20mm dia. |
| 86 | (a) Equal or reducing Socket, Elbow, Tee etc. (ii) 25 mm & 32mm dia |
| 87 | (a) Equal or reducing Socket, Elbow, Tee etc. (iii) 40mm dia. |
| 88 | (a) Equal or reducing Socket, Elbow, Tee etc. (iv) 50mm dia. |
| 89 | (b) Long screw/Union (i) 15 mm dia & 20mm dia. |
| 90 | (b) Long screw/Union (ii) 25 mm & 32mm dia |
| 91 | (b) Long screw/Union (iii) 40mm dia. |
| 92 | (b) Long screw/Union (iv) 50mm dia. |
| 93 | © Short Pieces upto 150mm long (i) 15 mm dia & 20mm dia. |
| 94 | © Short Pieces upto 150mm long (ii) 25 mm & 32mm dia |
| 95 | © Short Pieces upto 150mm long (iii) 40mm dia. |
| 96 | © Short Pieces upto 150mm long (iv) 50mm dia. |
| 97 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with standard size flush pipe, CP spreaders with unions and clamps with waste fitting as per IS : 2556, including painting of fittings and cutting and making good the walls and floors wherever required : |
| 98 | Providing and fixing white vitreous china water closet squatting pan (Indian type) : |
| 99 | Orissa pattern W.C. pan of size 580x440 mm |
| 100 | Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan. |
| 101 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 102 | 10 litre capacity - White |
| 103 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : |
| 104 | White solid plastic seat with lid |
| 105 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : |
| 106 | Flat back wash basin of size 550x400 mm. |
| 107 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 108 | (a) Flexible pipe (i) 32 mm dia |
| 109 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. |
| 110 | Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms. |
| 111 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall |
| 112 | 15 mm nominal outer dia. Pipes. |
| 113 | 20 mm nominal outer dia. Pipes. |
| 114 | 25 mm nominal outer dia .Pipes. |
| 115 | 40 mm nominal outer dia. Pipes. |
| 116 | 50 mm nominal outer dia. Pipes. |
| 117 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 118 | Providing and fixing PTMT swivelling shower, 15mm nominal bore. Weighing not less than 40 gms. |
| 119 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. |
| 120 | 15 mm nominal bore with 45 cm length. |
| 121 | Cutting holes up to 30x30 cm in walls including making good the same: |
| 122 | With common burnt clay F.P.S. (non modular) bricks. |
| 123 | Providing and fixing Aqua CPVC high pressure ball valve(Plastic Ball) of approved quality including the cost of necessary uPVC socket, pieces of pipes etc. required for the work complete as per direction of Engineer-in-Charge : |
| 124 | 20mm nominal bore. |
| 125 | 25mm nominal bore. |
| 126 | 40mm nominal bore. |
| 127 | Providing and fixing 15mm nominal bore, 195mm long PTMT shower arm. |
| 128 | Providing and fixing soil, waste and vent pipes uPVC soil waste pipe conforming to ISI No.13592 1992 (TYPE-B) manufactured by Supreme or equivalent. |
| 129 | 110 mm outer dia Type-B pipe. |
| 130 | Providing and fixing uPVC fittings for new and repairs to soil waste and vent pipe(TYPE-B) with necessary rubber ring, solvent cement, gasket etc. complete as per direction of Engineer-in-Charge. (a) 110 mm dia. |
| 131 | Door bend (T/S) of required degree with access door. |
| 132 | Single Tee with door. |
| 133 | W.C. connector straight (Reducer type) (125 X 110 mm). |
| 134 | P Trap(125x110mm with WC ring). |
| 135 | Vent Cowl. |
| 136 | Removing chokage and repairing leakage of water pipe lines as and when required including cost of jointing materials such as zinc, jute etc. require to sealing the leakage of joints (Cost includes for necesary scafoldings require for out side pipe line of building upto floor-V level. Cost for fittings and pipes if required will be paid seperately). |
| 137 | 15mm to 50mm nominal dia pipe. |
| 138 | Supplying, fitting and fixing C I brackets /15 mm dia GI pipe as brackets including two coats of painting as per direction of the Engineer-in Charge for wash basin, sink etc. |
| 139 | Providing and fixing stainless steel grating of approved quality and colour. (a) Circular type. (i) 100 mm nominal dia. |
| 140 | Providing and fixing brass C. P. bib cock of approved quality : |
| 141 | (a) 15 mm nominal bore |
| 142 | Providing and fixing C. P. brass stop cock of approved quality : |
| 143 | (a) 15 mm nominal bore |
| 144 | Providing and fixing C. P. brass Pillar cock of approved quality : |
| 145 | (a) 15 mm nominal bore |
| 146 | Providing and fixing C.P. brass health faucet with 1m long hose of approved brand and manufacture and of approved shade |
| 147 | (a) 15 mm nominal bore |
| 148 | Providing and fixing C.P. brass two way bib cock of approved brand and manufacture and of approved shade |
| 149 | (a) 15 mm nominal bore |
| 150 | Providing and fixing C. P. Brass angle stop cock of approved quality. |
| 151 | (a) 15 mm nominal bore |
| 152 | Removing chokage of water closet. |
| 153 | Periodic cleaning of sewer line, sewer manhole, sewer gully chamber and storm water underground line, storm water line inspection pits, storm water road side gully pits etc. by using bamboo/rod for clearing the sewer/storm water line,taking out sludge, debris, rubbish and other waste materials, if any, from the sewer/storm water line and flooding/flushing with sufficient quantity of water with pressure to ascertain through cleaning of drainage system for smooth and proper functioning of sewer/storm water line including disposal of the all waste material outside the municipal limit or burried into pits at safe available distance as directed all complete. (Note-The operation includes cost of all and nothing shall be paid extra on any account). |
| 154 | Underground Sewer line/Storm water drainage line upto 150mm dia |
| 155 | Sewer line/Storm water inspection Pit. |
| 156 | Storm water drainage Gully Pits. |
| 157 | Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge |
| 158 | 75 mm average thickness |
| 159 | 50 mm average thickness |
| 160 | 25 mm average thickness |
| 161 | Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge. |
| 162 | Bars upto 12 mm diameter |
| 163 | Bars above 12 mm diameter |
| 164 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect. |
| 165 | SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer |
| 166 | Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge. Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2). |
| 167 | 12 mm average thickness. |
| 168 | 25 mm average thickness in 2 layers. |
| 169 | 50 mm average thickness in 3 layers. |
| 170 | Applying anticorrosive passivating coat on cleaned reinforcement rust free steel surface/new reinforcement surface by Anticor, the corrosion resistant chemicals for reinforcing bars, unique formulated water based passivating chemicals of Engineering Services International or equivalent with paint brush three or more coat before 24 hours of its application of protective concrete/morter coat and allowing it to dry, all complete as per direction of Engineer-In-Charge. |
| 171 | Bars upto 12 mm diameter . |
| 172 | Bars above 12 mm diameter |
| 173 | Providing and fixing single scaffolding system on the exterior side of building/structure, including additional rows of scaffolding in stepped manner as per requirement of site, made with 10 cm dia. bamboo ties @0.90 metre apart fitting and fixing with necessary coir,nails etc. horizontal & vertical with working platform etc. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. |
| 174 | For through external external repairs and maintenance works up to 25m height of building. above ground level. |
| 175 | Extra for providing, mixing 10 mm graded stone agreegates with modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand ) in the ration of 50: 50 Coarse Sand: graded Stone agreegate that is in ratioo of 1: 2:2 (1Cement :2 Coarse sand: 2 10mm graded stone agreegate) in liue of cement mortar 1: 4, as per specifications and directions of Engineer-in-charge. |
| 176 | Extra for 25 mm average thickness in two layer. |
| 177 | For 50 mm average thickness in 3 layers. |
| 178 | Extra for providing, extra thickness of cement concrete 1:2:2 (1 cement: 2 coarse sand : 2 10mm graded stone agreegate over existing schedule for 50mm average thickness in three layers, as per specifications and directions of Engineer-in-charge. |
| 179 | For average 25 mm extra thickness over schedule item of \\"Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) \\" . |
| 180 | Replacement of sufficiently damaged reinforcements or providing additional reinforcements with the damaged reinforcement by welding etc. including cost of reinforcement(TMT bar of required dia) complete as per direction of the Engineer-in-charge. (Work is to be executed upto 50 m heights above G.L) |
| 181 | Credit value for dismantled unserviceable/ serviceable departmental materials: |
| 182 | Iron/Steel materials (Flat, Angle, Tee, Channel, Joist, Plate, Sheet, Reinforcement etc.) |
| 183 | Unserviceable Corrugated Galvanised Iron Sheet Please Enable Macros to View BoQ information |
