|
| 1 | Dismantling of plain or corrugated steel sheeting of any gauge ,thickness as in roof covering complete all as specified and as directed. |
| 2 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed |
| 3 | Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 4 | S & F for 0.63 mm thick galvanised corrugated mild steel sheeting with two corrugation side lap , fixed with 'J' or 'L' type or cranked hook bolts and washers in roof covering etc with grade of zinc coating 120 complete all as specified and directed. |
| 5 | S & F for 0.63mm thick plain galvanised mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 120 complete all as specified and directed. |
| 6 | Demolition of stone or brick masonry, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc., complete, including removal of debris to a distance exc 1.5 km but n.exc 2 km, complete all as specified and directed. |
| 7 | Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed. |
| 8 | Dismantling of wall/ceiling board (fibre, pulp, Insulation etc.) or insulation of boards/slab /blankets, any thickness with frame work including cover fillets cornices etc. complete all as specified and as directed. |
| 9 | GI frame work anodised snap grid frame work of size of size 605 mm X 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer's catalogue/ instructions), cutting holes for electrical fittings fixed on and including aluminium tee of size 25mmX25mmX1.50 mm as main runner, aluminium tee of size 25mmX25mmX1.25 mm as cross runner and aluminium angle of size 25mmX25mmX1.25mm at the perimeter suspended from soffit at approx 900 mm centre to centre with hangers 6 mm dia galvanised (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanised iron flat 40 mm X 3 mm size, 60 mm long and expansion hold fasteners 12.5 mm dia, 40 mm long including necessary scaffolding all as specified and directed. |
| 10 | 6 mm thick non asbestos fibre cement building boards of size 600x600mm (ED board) as in ceiling fixed or laid/ inserted to timber/ GI/ aluminium frame work fixed with nails, all as specified. |
| 11 | Dismantling Timber scantling, over 40 Sqcm in Section, in any position, in framed work, complete all as specified and as directed. |
| 12 | Dismantling Timber scantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, framed or unframed work complete all as specified and directed. |
| 13 | M & L for second class hard wood in scantling clean sawn fixed in framed work complete all as specified and directed |
| 14 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.. |
| 15 | Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.290 Gde E-165, steel work, complete all as specified and directed. |
| 16 | S & F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240 complete all as specified and directed. |
| 17 | Dismantling boarding, any description fixed in any position with nails complete all as specified and directed. |
| 18 | S&F 15mm thick 2nd class hardwood boarding planed one side with butt joints & and fixed with nails in any situation complete all as specified and directed. |
| 19 | Demolition of cement concrete (unreinforced) of of any descriptions, in ground floors (Floor Topping, Sub Base etc) not exc 150mm thick, above or below ground level complete all as specified and directed. |
| 20 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed |
| 21 | Plain cement concrete M-15, nominal mix, type B-0, using 12.50mm graded mechanically crushed stone aggregate as in top layer of flooring, 25mm thick, surface finished even and fair for receiving floor finishes, complete all as specified and directed. |
| 22 | Machine cut kota stone slab flooring 18-20mm thick of size not less than 550 mm X 550mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:6 (1 cement : 6 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, laid over PCC sub base, complete all as specified and directed. |
| 23 | Machine cut kota stone,18-20mm thick, as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in vertical surfaces such as skirting/dado/riser to step/pillar aid over and including 10mm thick bedding layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, complete all as specified and directed. |
| 24 | Vitrified ceramic tiles light shade, 10mm thick (Square/ rectangular) area of each tile exc. 0.36 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed. |
| 25 | Vitrified ceramic tiles light shade, 10mm thick (Square/ rectangular) area of each tile exc. 0.36 Sqm, in vertical surfaces such as skirting and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick rendering in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed. |
| 26 | Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed. |
| 27 | Glazed coloured tiles of size 350x250/450x350/450x300x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed. |
| 28 | M & L for 75 mm thick Plain cement concrete M-7.5 nominal mix, type D-2, using 40mm graded mechanically crushed stone aggregate as sub base to floor, surfaces finished even and fair complete all as specified and directed |
| 29 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 30 | M & L for chequered cement concrete tiles of size 30cmx30cmx25mm thick with grey cement and pigment , set and jointed in neat cement slurry over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 31 | Taking down cement plaster of any description on brick/stone walls, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, remove dust, debries/rubbish etc complete all as specified and as directed. |
| 32 | M & L for rendering 15mm thick in cement mortar 1:6 on other than fair face of brick work or on concrete surfaces, finished even and smooth with using using extra cement complete all as specified and as directed. |
| 33 | M & L rendering 15mm thick in cement mortar 1:4 on external fair faces of brick work or concrete surfaces plastered surfaces finished even and smooth without using extra cement with water proofing compound as per manufactare instruction complete all as specified and directed. |
| 34 | Supply only integral water proofing compound complete all as specified and directed.. |
| 35 | M & L 5mm thick rendering in cement mortar 1:3 on ceiling surfaces, finished surface even and smooth, without using extra cement complete all as specified and as directed. |
| 36 | Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of 2 mm thick wall care putty preparatory to distempering including preparation of surface complete, all as specified and as directed by Engr-in-Charge complete all as specified and directed. |
| 37 | Preparation of newly plastered wall surfaces and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali and fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 Litre/ 10 sqm, complete all as specified and directed. |
| 38 | M & L for preparing new surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed. |
| 39 | M&L for Two coats of cement base paint with mechanical roller on newly plastered surfaces including preparation of surface complete, all as specified and as directed. |
| 40 | M & L for preparing new surfaces of walls and applying three coats of white wash, complete all as specified and as directed. |
| 41 | M&L for 50mm thick cement concrete 1:3:6, type C2 using 20mm graded stone aggregate as in plinth protection and similar works finished even and smooth without using extra cement complete all as specified and directed. |
| 42 | Taking down Chowkats or Frame (without taking off shutter from the frame) exc. 1.50 sqm but n exc 4.00 Sqm each complete all as specified and as directed. |
| 43 | Taking down Chowkats or Frame (without taking off shutter from the frame) n exc. 1.50 sqm complete all as specified and as directed. |
| 44 | Taking down shutters of any description but exc. 1 Sqm and n exc. 2 Sqm each complete all as specified and as directed. |
| 45 | Taking down shutters of any description n.exc 1 Sqm each complete all as specified and as directed. |
| 46 | S&F Pressed steel frames size 125 x 60mm, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed. |
| 47 | M&L for PCC type C-1 (1:3:6) using 20mm graded curshed stone aggregate as in filling in door frame and mass concrete etc complete all as specified. |
| 48 | S/F 35 mm thick 2nd class hard wood rail and style mm plain framed, factory made panelled shutter (one panel) without interlocking rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and size as per IS:1003 (part I), kiln seasoned and chemically pressure treated complete all as specified and as directed. |
| 49 | S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specifeid. |
| 50 | S/F 35 mm thick 2nd class hard wood glazed and skelton shutter open rebated and prepared to receive glass gauze etc (without shas bar) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of numbers of shutter as specified in SSR Part-I Section 8, clause 8.2 (a) complete all as specified and as directed. |
| 51 | S & F Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads complete all as specified and as directed. |
| 52 | S & F Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed in repair with stainless steel wire staples or wooden beads complete all as specified and as directed. |
| 53 | Hacking old broken glass (any thickness, size, quality or description) from wooden Frames/metal frame , glazed with wooden beads complete all as specified and as directed. |
| 54 | S & F for sheet glass, 4.0mm thick glazing with beads or oil putty with glazing clips, not exc. 0.50 sqm in each pane, complete all as specified and as directed. |
| 55 | Ditto all as per item No 54 above but pin headed complete all as specified and directed. |
| 56 | M & L appying two coats synthetic enamel paint over a coat of pink primer on wooden surface any description over 10 cm in width or girth not otherwise described including preparation complete all as specified and as directed. |
| 57 | Preparation of new steel and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 58 | Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed. |
| 59 | Factory made solid panel PVC door shutter 30 mm thick consisting of frame made out of MS tubes for Top & bottom nails MS framed shall be covered with neat moulded plain coloured PVC 'C' channel having PVC sheet ship if 20 mm width stuck inside with solvant cement for style and plain colour PVC shutters for top rail lock rail and bottom rail on edges side & gap insert for top rail bottom rail panelling of plain colour PVC sheet truck and nail with suitable PVC sheet bedding and jointed to shutter with solvent gear supply and fixing in the frame at site complete all as specified and as directed. |
| 60 | S & F 150 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed. |
| 61 | S & F 100 mm long aluminium anodised barrel tower bolt complete all as specified and as directed. |
| 62 | S & F 150 mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 63 | S & F 100 mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 64 | S & F 100 mm long stainless steel Butt Hinges Medium Weight, Cold Rolled and fixed complete all as specified and as directed. |
| 65 | S & F 75 mm long stainless steel Butt Hinges Medium Weight, Cold Rolled and fixed complete all as specified and as directed. |
| 66 | S & F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. |
| 67 | S & F in repair Vitreous china wash down water closet pan (Pedestal pattern), white fixed in repair with plastic water closet seat, black,closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device including PVC valveless, syphonic action type,10 ltr capacity flushing cistern, low level, white with inlet, ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32mm dia for low level cistern complete all as specified and as directed. |
| 68 | Wash hand basins, Vitreous China (oval type, coloured) size 435 mm x 505 mm x 180 mm, excluding tap etc including cast iron brackets duly painted including cutting and pinning in ends and making good disturbed surfaces in cement mortar (1:3) as well as matching with existing with 32 mm bore waste fittings, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, PVC connections 15mm size with CP brass coupling nuts of length 450mm, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, chain and plug, PVC 32mm dia flush pipe and all accessories fixed in repairs complete as all specified. Make: Cat Part No. KUS-WHT-35601 of Jaquar or equivalent in makes mentioned in Appx 'C' |
| 69 | S & F in repair Vitreous china squatting pan, Orissa pattern, size 580x440mm white, with integral foot rests including provision of lime concrete bedding and PVC valveless, syphonic action type,10 ltr capacity flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with fixing of flush pipe of polyethyne of low or high density or PVC 32mm dia, for low level cistern complete all as specified and as directed. |
| 70 | S & F in repair Vitreous china wash basin size 550x400mm (flat back or angle back type) including 32mm dia waste fittings, brass chromium plated for glazed ware sinks,basins, etc. with long screwed shanks and flynuts, flange end bedded in red lead cement and other end fixed with provision of 15mm bore dia pillar taps fancy type chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed. |
| 71 | M &L HDPE waste pipe of 32mm dia pressure rating 6 Kgs/Sq cm fixed wash basin, sinks etc complete all as specified and directed. |
| 72 | S & F in repair bevelled edge looking mirror of selected quality of size 600 x 450x 5.5mm thick, mounted on 6mm thick AC building board or commercial ply and fixed to wooden plugs and CP brass screws and cup washers complete all as specified & directed |
| 73 | Brass Chromium Plated, tubular towel rail, 19mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated screws, fixed in repair, complete all as specified and directed. |
| 74 | Taking down or up steel 15mm bore water tubing and connections including cleaning for re fixing or removal to store complete all as specified and as directed. |
| 75 | Taking down or up steel 20mm bore water tubing and connections including cleaning for re fixing or removal to store complete all as specified and as directed. |
| 76 | M & L 15mm dia bore steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified & directed |
| 77 | M & L 20mm dia bore steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed. |
| 78 | S & F in repair Bib taps cast copper alloy 15mm bore Chromium Plated , screwed down high pressure with crutch or butterfly handle, screwdd both ends for iron pipe or for unions and fixed complete all as specified and as directed. |
| 79 | S & F in repair Brass CP Shower Rose 125mm size with or without swivel joints, any size including fixing to steel pipe or union complete all as specified and as directed. |
| 80 | S & F angular stop cock 15mm bore fancy type Chromium Plated with wall flange complete all as specified and directed. |
| 81 | Harrison 25mm bore Curtain rails, mild steel, chromium plated with fixing brackets, stops and roller etc. fixed in repair, complete all as specified and directed. |
| 82 | Disconnecting existing tanks and removing to store water tanks of capacity n.exc 500 litre, complete all as specified and directed. |
| 83 | Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding brass ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line, complete all as specified and directed. |
| 84 | Disconnecting existing tanks and removing to store water tanks of capacity exc 500 but n.exc 1000 litre, complete all as specified and directed. |
| 85 | Rotational moulded polyethylene water storage tank 1000 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding brass ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line, complete all as specified and directed. |
| 86 | S & F in repair Steel Plate Rack made of stainless steel 0.60mm Thick size 900x750mm, 250mm deep, fixed in position with plugs, washers and steel screws, complete all as specified and directed. |
| 87 | S & F in repair sinks with drainage board made of stainless steel 1mm thick kithcen or laboratory with plugs, washers and wastes, including bedding in cment mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm and bowl size 410 mm x 330 mm x 160 mm, complete all as specified and directed. |
| 88 | S & F 20mm dia ball brass valve high pressure with polythene float and fly nut complete scrwed for iron pipe or brass ferrule and fixed complete all as specified and directed. |
| 89 | S & F 20mm dia ball brass valve high pressure with polythene float and fly nut complete scrwed for iron pipe or brass ferrule and fixed in repairs complete all as specified and directed.. |
| 90 | S&F in repair PVC valveless, syphonic action type,10 ltr capacity flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with fixing of flush pipe of polyethyne of low or high density or PVC 32mm dia, for low level cistern complete all as specified and as directed. |
| 91 | PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of bore 110mm, complete, including taking up or down old pipe, complete all as specified and directed. |
| 92 | PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of bore 75mm, complete, including taking up or down old pipe, complete all as specified and directed. |
| 93 | PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors bore 110mm, including taking up or down old pipe, complete all as specified and directed. |
| 94 | PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors bore 75mm, including taking up or down old pipe, complete all as specified and directed. |
| 95 | M & L for PVC (SWR) 110mm bore (dia), Bends any type, with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed. |
| 96 | M & L for PVC (SWR) 75mm bore (dia), Bends any type, and Jointing with Solvent Cement, complete all as specified and as directed. |
| 97 | M & L for PVC (SWR) 110mm bore (dia), Single T Junction equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed. |
| 98 | M & L for PVC (SWR) 75mm bore (dia), Single T Junction equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed. |
| 99 | S & F for PVC (SWR) floor trap 75mm with gratings including Jointing to waste pipe with solvent cement complete all as specified and directed. . |
| 100 | S & F 5.5mm thick Sheet glass, ordinary quality and fixed with rubber packing and aluminium snap beading in aluminium doors in square exc 0.5 sq. m in each pane complete all as specified and directed. |
| 101 | Mortice lock, brass, vertical type, size 100mm, 4 lever, fixed into aluminium door shutter, complete all as specified and directed. |
| 102 | S & F Aluminium (die cast body) door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg. fixed in repair complete all as specified and directed. |
| 103 | S & F 140mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 104 | M & L Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover,governing pivot made of brass,other parts made of mild steel heavy duty and fixed in repair complete all as specified and directed. |
| 105 | Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; flat iron for framing grills, framework of water tanks and similar work conforming to Fe.290. Gde-E-165, all as specified. |
| 106 | Chromium plated (Health Faucet) (ABS Body) with 1 Meter Long PVC Tube & Wall Hook and fixed in repair, complete all as specified and directed. |
| 107 | Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) including 10mm square MS bar grill and finishing the surfaces to match with existing including following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window.(ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf.(iii) MS tower bolt 150mm long - 2 No per leaf(iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf.(v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf.(vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf.(vii) Flat iron fillets of size 20X3 mm for fixing wire gauge.(viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 06/07.Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day. |
| 108 | Taking down aluminium door shutter n. exc. 2 sqm each, taking out servicable glass panes, hydraulic door closer, butt hinges, double action hydraulically regulated floor spring and other fittings, if required carefully and refixing in the same opening after repairs of unservicable or loosened joints/cleats of top rail/bottom rails/ lock rails and styles etc and fixing old servacable glass, any thickness with rubber packing and aluminium beadings, fixing of old servicable hydraulic door closer, double action door spring duly oiling/greasing and fixing all servicable fittings complete all as directed by Engr-in-charge. NOTE:- Unservicable door closer, double action floor spring, glass panes and other fittings etc shall be replaced and paid under separate items of schedule. |
| 109 | Natural colour 15 micron anodized powder coated aluminium door chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing door handles, tower bolts, mortice lock, hinges, door stopper including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- a) Shutter vertical member 85.00 x 44.45 x 1.80mm weighing 1.302 Kg/RM.b) Shutter top member 83.5 x 44.45 x 1.70 mm weighing 1.243 Kg/RM.c) Shutter bottom member 114.30 x 44.45 x 1.29mm weighing 1.139 Kg/RM.d) Shutter lock rail 83.5x44.45x1.70mm weighing 1.243 Kg/RM.e) Anodised aluminium handle, fancy type, 350mm long and aluminium tower bolt of size 150mm.(f) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (g) Aluminium anodised frame of door of section 101.6 x 44.45 x 1.75mm weighing 1.367 Kg/M, with flat iron hold fasts and necessary concrete in PCC M-15, type B-I using 12.5 mm graded crushed stone aggregate to fix hold fasts all as directed. |
| 110 | Natural colour 15 micron sliding three track anodized aluminium powder coated window with chowkhat of approved design complete all as directed with all fixing arrangements (including providing and fixing window handles, tower bolts and provision for fixing lock) including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a)Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881 Kg/RM.(b)Shutter top member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM.(c)Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM.(d) Natural colour 15 micron anodized aluminium anodised frame of chowkhat of section 85.00 x 44.45 x 1.80 mm weighing 1.302 Kg/ RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed.(e) 5.50mm thick tinted glass fixed with alumnium beading, silicon lining and gaskets complete. (f) The size of anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and anodised aluminium tower bolt of size 100mm (02 Nos). |
| 111 | Taking down cement plaster of any description on concrete surfaces of roof including racking out joints, hacking for key, scrubbing down with water, remove dust, debries/rubbish etc complete all as specified and as directed. |
| 112 | M&L for 15mm thick (average) screed bed /plaster in cement mortar 1:4 in order to maintain proper slope of existing RCC roof all as specified and directed. |
| 113 | Water proofing treatment over terrace using SHALIURETHANE- BTD OF STP MAKE OR EQUIVALENT as approved by GE in two coats @ 1 kg/sqm in each coat, high solid content single component water based liquid applied elastomeric water proofing membrane as ASTMC 836 and ASTMD 6083, thickness of the membrane shall be 1.5mm, having solid content of more than 80% elongation of 500+(-) 50%, laid over reinforcing layer on non woven geo-textile mesh of 40/50, 50 gms, including applying self primer coat by diluting with 1:1 ratio @ 0.40 kg per sqm and surface preparation including cleaning of existing treatment complete all as specified and directed. |
| 114 | Disconnecting of existing PVC /Ferro cement/MS Tank of capacity exc 250 ltr but n exe 500 ltrs for cleaning and removing all scale and dirt etc from tanks and from mouth circulating pipes etc and hoisting if required , reconnecting and refixing in position all as directed by Engr-in-Charge |
| 115 | Disconnecting of existing PVC /Ferro cement/MS Tank of capacity exc 500 ltr but n exe 1000 ltrs for cleaning and removing all scale and dirt etc from tanks and from mouth circulating pipes etc and hoisting if required , reconnecting and refixing in position all as directed by Engr-in-Charge |
| 116 | Granite (of any type) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement(1:2) with admixture of pigment to match the shade of granite stone including grinding and polishing complete as in kitchen platform, window cill /steps laid over and including 15mm thick screed bed in cement mortar (1:6), complete all as specified and directed. |
| 117 | Solid PVC Wall Lining consisting of 5mm thick wood grain printed sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing |
| 118 | S&F in repair Black out roller blinds of required and shade and necessary fitting of Johnson or equivalent Make complete all as per direction of Engr in Charge/GE |
| 119 | S&F in repair 8mm thick Laminated wooden flooring with plank size not less than 1200mmx190mm (with unilin/tongue-groove locking arrangement) having 0.2mm thick top abrasive layer over a decorative layer followed by a hingh density fiber board having densitry > 850kg/cum , substrate core over a rasin saturated packing layer and installing through unilin/tongue-groove system (having locking strenght not less than 1000kg/mtr) over a 2mm thick under layer polyurethene foam on polythene sheet 250micron over a smooth/flat hard sub-floor free from moisture (less than 8%), grease etc complete in all respect requisite accessories like end profile tranisition profile , reducer tee profile etc wherever required and preparation of base including all other incidental works as per direction and satisfaction of Engineer-in-Charge. |
| 120 | M & L for mirror polishing of existing machine cut Kota stone/ganite/ marble flooring, skirting, steps of 18-20 mm thickness, complete all as specified and directed. |
| 121 | GI frame work for seamless ceilling comprising of GI permeter channel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.90mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section of 0.55mm thickness having kurled web of 50mm and flange of 26mm each lips of 10.50mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre including Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish and applying two coats of distemper over 1mm thick wall care putty, complete all as specified and directed by Engr-In-Charge. |
| 122 | M&L for sunken slab treatment comprising of following: a) Taking out/down old existing sunken slab treatment including tiling, PC and cleaning the old RCC surfaces of sunken slab including removal of the rubbish out of campus complete all as specified. (b) M&L for 25mm thick PCC type B-1 using 20mm graded stone aggregate over cleaned sunken slab surfaces. (c) M&L for applying bitumen priming coat/tack coat over PCC @ 0.30 kg/Sqm. (d) M&L for 4mm thick APP modified water proofing membrane weighing not less than 4 Kg/Sqm reinforced with non-woven polyester matt weighing not less than 160gm/sqm including minimum 10cm side lap and 15cm end lap torch sealed and bound. (e) M&L for applying bitumen grade 85/25 over primer coat @ 1.20 Kg/Sqm. (f) M&L for 25mm thick plastering (in two layers 15mm 1st layer, 10mm second layer) in Cm 1:4 mixed with liquid water proofing admixture as per manufacturer instruction over and including 225mm thick PCC 1:4:8 using 40mm graded stone aggragate complete all as specified and directed by Engr-In-Charge. |
| 123 | S&F in repair wall panelling consist of heavy duty aluminium box section 50mm x 50mm @ 600mm c/c both ways horizontally and vertically. The vertical alternate frames to be fixed to the ceiling with necessary fixtures. The framing shall be finished with 12mm commercial ply and finished with 1 mm thick veneer finished with melamine polish. The shade of laminate/veneer and polishing finish to be got approved from GE/Engr in Charge. The rates shall inclusive of necessary hardware items etc complete all as specified and directed. |
| 124 | S&F in repair one piece floor mounted toilet water closet of size (WxPxH) 360 x 675 x 750 mm white or tinted S trap 300 mm trendy square design slim UF ezee seat cover wash down system dual flush (6/32 ltrs) mechanism with necessary fixing E145bolts/screws etc complete all as specified. Make Jaguar Cat no OPS-WHT 15853S300UF, Somany, Cera or Equivalent |
| 125 | S&F in repair counter top vitreous china wash basin premium quality of size 610 x 385 x 130mm including brackets waste coupling & pipe of 32 mm dia and fixed with including all connected items. |
| 126 | S&F in repair 12mm thick toughened glass partition (with or without opening/door shutters with diamond polished edge, clear glass including all hardware fittings detailed as under, fixed in position as per manufacturer instructions including following fittings complete: (a) Stainless steel top patch (cat No. EPF-701) 01 set (b) Stainless steel top pivot (cat No EPF-712) 01 set (c) Stainless steel bottom patch (Cat No EPF-702) 01 set (d) Glass to wall stainless steel lock (Cat No FH-ECO - 842) 01 set (f) Stainless steel Handle 300mm size (Cat No ESBH-011) 02 Nos for each shutter, Note: Cat No mentioned above for hardware fittings are of make ENOX, contractor may use similar type hardware fitting of make DORMA/OZONE. Make of glass ATUL/MODI/GURD/SAINT GOBAIN/ JINDAL/ INDAL/ HINDAL/ WALCO. |
| 127 | Supply fabricaton & fixing in position aluminium partition wall with top, middle and bottom frame of size 101.60x44.45x1.75mm weighing 1.367KG/RM, partly glazed with 5.5mm thick tinted glass with or without sash bars and partly panelled with 4 mm thic ACP board with both side decorative including rubber bead joining cleat for fixing in position, complete all as specified and directed by Engr-In-Charge. |
| 128 | Preparation of CGI/PGI sheet roof surfaces by removing all loose gravel, dust, dirt, corrosion, oil grease and other foreign materials by jet of dry air and clean the CGI/PGI sheet surfaces mechanically or by grinding to make the surfaces smooth and M&L for applying ShaliSeal PS PG conforming to SI-12118 Part-I; 1987 to seal holes of J/L hooks and applying one coat of cold applied adhesive ShaliBond APP @ 3.00 Sqm per Kg (Approx) on CGI/PGI Sheet surfaces as bonding adhesive to affix bituminous membrane with brush. S&F for unroll the APP membrane 1.50mm thick (TarFelt APP conforming to ASTM D-5147) over the tacky surface and bond it to the CGI/PGI sheet surfaces by applying unifrom pressure and finally membrane shall be coated with Super Silver sheild @ 7 to 9 Sqm/ltr to protect the membrane from UV rays and prevent degradation arising of exposure to sun light. Note: Roof treatment shall be carried out by expert applicator of the firm. Please Enable Macros to View BoQ information |
