|
| 1 | M&L screed bed or bedding layer 15 mm thick in cement mortar 1:6 on floors for laying floor finish complete all as specified and as directed. |
| 2 | M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 3 | M&L Pre-cast cement concrete block masonry 1:2:4, type B1 solid blocks, exc. 10cm in width and setting in CM (1:4) all as specified and directed. |
| 4 | M&L for RCC Type B1 (1:2:4) (20 mm graded aggregate) as in Beams, cantilevers, bressummer, lintels over 1.5m span complete all as specified and directed. |
| 5 | S&F TMT bars 10mm dia and over cut to length, bent to shape required including cranking etc and binding with 0.90mm wire MS wire complete |
| 6 | S&F TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, complete all as specified and directed. |
| 7 | Use and waste for formwork to sides and soffits of floor or roof beams, beam haunching's, girder, bressummers, lintels, cantilevers, shelves including supports, overhangs etc, complete all as specified and directed. |
| 8 | M&L for rendering 15mm thick in cm 1:4 on brick masonry surfaces or concrete surfaces on other than fair face of wall surfaces with sponge finish, complete all as specified and directed. |
| 9 | M&L for rendering 5mm thick in CM (1:4) finishing coat mixed with WPC over 10mm thick CM (1:6) backing coat on brick / concrete surfaces finished even and smooth without using extra cement |
| 10 | Supply only integral waterproofing compound |
| 11 | M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489: 2004, Alkali & fungal resistance , dirt resistance exterior paint of required shade ( company depot tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10sqm over new surfaces complete all as specified and directed. |
| 12 | M&L for preparation of putty surfaces and applying for 2 coats of oil bound distemper / acrylic emulsion over one coat of primer on ceiling |
| 13 | Supply & fixing of PUF insulated wall panels 50mm thick factory made , sandwich type panels consisting of pre-painted galvalume steel sheets 0.50mm thick on both sides with rigid polyurethane foam (density 38-42 kg/cum) insulation in between including joint sealing using silicone sealant complete all as specified and directed. |
| 14 | M&L for Steel rolling shutters, with out ball bearing, as specified including top cover, an- choring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type thickness of lathe 1.25 mm complete all as specified and as directed. |
| 15 | M&L for joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc Fe 410-W (Gde-250) quality -A complete all as specified and as directed. |
| 16 | M&L for plates (plain or chequered) channels, squares cut or notched (ordinary and counter sunk) forming holes, without any attachment |
| 17 | M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified. |
| 18 | M&L for preparation of old painted steel and iron surfaces and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer |
| 19 | Excavation in trenches, not exc 1.5 mtr deep and exc 1.5 m wide and getting out in soft/ loose soil in any description. |
| 20 | M&L for PCC type D2 1:4:8 using 40mm graded stone aggregate as in foundation filling. |
| 21 | M&L Pre-cast cement concrete block masonry with solid blocks, Type C1 1:3:6 exc. 10 cm in width and setting in mortar 1:4 mortar. |
| 22 | M& L for 15mm thick cement plaster on PCC block masonry surface finished even and smooth without using extra cement in CM 1:6 complete all as specified. |
| 23 | M&L for three coats of white wash |
| 24 | M&L for cement concrete 1:3:6 , type C-1 using 20mm graded stone aggregate as in copings , band plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed. |
| 25 | S&F for 450mm dia reinforcement concrete pipes NP3, laid and jointed complete with collars |
| 26 | M&L for reinforcement concrete M-20 using 20mm graded stone aggregates |
| 27 | Returning filling in including spreading levelling watering & well ramming in layers n exc 25cm each in soil. |
| 28 | Removal of excavated material n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point in soil |
| 29 | Use and waste of form work to sides or faces of concrete to sides or faces of concrete walls , retaining walls , abutments , parapets and similar work including attached pilasters for flat and rough surfaces. |
| 30 | M&L for PCC C2 type (1:3:6) using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed. |
| 31 | M&L for precast cement concrete block (1:3:6 Type C1) masonry with solid blocks,exc 10 cm in width and setting in mortar 1:6. |
| 32 | M&L for 10 mm thick cement plaster in CM 1:4, on PCC block Wall finished even and smooth without using extra cement complete. |
| 33 | Extra for forming fair finished drain or channels 45 cm inner girth in Cement concrete using extra cement including forms, moulds mitred/ stopped ends etc. in manholes. (inner girth only measured). |
| 34 | Reinforcement with TMT bars 10mm dia and over cut to length, bent to shape required including cranking etc and binding with 0.90mm wire MS wire complete |
| 35 | M&L for Precast cement concrete Type B1 1:2:4 (20mm graded aggregate) set in CM 1:4, in landings, cover slabs (for manholes etc) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces. |
| 36 | M & L for Moorum/red bajri filling in floors or paving's, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering etc complete all as specified and directed. |
| 37 | M & L for Hardcore of gauge not exceeding 63mm of broken stone or boulder's, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface etc complete all as specified and directed. |
| 38 | M & L for providing 100mm thick PCC(1:4:8) type D-2 using 40mm graded stone aggregate for sub base complete all as specified and directed. |
| 39 | M & L for providing 100mm thick PCC(1:2:4) type B-1 using 20mm graded stone aggregate for flooring complete all as specified and directed. |
| 40 | M&L for 75mm thick PCC (1:3:6) type C2 (40mm graded aggregates) as in plinth protection complete all as specified |
| 41 | M&L for Anodised aluminium frame for doors, windows, ventilators and partitions with one or more rebates including joining cleat for fixing etc. complete all as specified complete all as specified. |
| 42 | Supply & fixing of Anodised aluminium Sections for door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges/pivots etc for fixing purpose anodised aluminium snap beading screws etc. complete all as specified. |
| 43 | Dismantling of galvalume aluminium zinc coating GI based plain or corrugated steel sheets of any thickness in roofing all as specified and directed. |
| 44 | S & fixing of Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding/ridge to wall fixed with self tapping screws as specified. |
| 45 | Supply & fixing of 4.0 mm thick Sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane fixed to Aluminium windows/ventilator etc complete all as specified and directed. |
| 46 | S&F in repairs Aluminium alloy, anodised, sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed. |
| 47 | Supply & fixing of 150 mm long aluminium anodized barrel tower bolts of extruded sections as fixed complete all as specified and directed. |
| 48 | Supply & fixing of 100mm extruded aluminium alloy handles, cast type as fixed complete all as specified and directed. |
| 49 | S&F in repairs extruded aluminium alloy butt hinges 100mm size with galvanised mild steel hinge pin type C-21 complete all as specified and directed |
| 50 | M&L for point wiring using approved colour coding as per IS (Red , Black and Green for single phase circuits),with multistranded copper conductor 1.5 sq mm nominal cross-sectional area , single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade, ISI-694 marked with valid CML No.in and including medium grade, PVC conduit minimum 20 mm dia concealed in wall/floor/ceiling and accessories etc, ISI marked with mild steel/pressed steel sunken box (with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally. and two coats of black bituminous paint over a coat of red oxide primer externally, with white cover plate with frame for mounting switches, socket and fan regulators etc, including PVC insulated multistranded copper conductor 1.5 sq. mm nominal cross sectional area single core FR LS cable as earth continuity conductor to common earth and connecting to earth duly completed all as specified and directed by Engr-in-charge for the following :- |
| 51 | One light point controlled by one switch |
| 52 | All as per item No 50 here-in-before but wiring with 2.5 sqmm single core multi stranded copper conductor 1100 v grade PVC insulated but unsheathed copper conductor FRLS cable 1100 volts grade and 2.5 sqmm PVC insulated but unsheathed FRLS cable as earth wire for 16 Amps power point on independent board complete all as specified and directed by Engr-in-charge. |
| 53 | Supply and fixing of switch piano 5 Amps one way flush type, matching with existing make, ISI marked, all as specified and directed. |
| 54 | Supply and fixing of Ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body complete all as specified and directed. |
| 55 | Supply and fixing of switch socket combination 16 Amp, flush type, ISI marked, all as specified and directed. |
| 56 | Supply and fixing of wall mounted extruded aluminium housing high quality indoor batten LED tube 20 watt colour temperature 6500 K (4' long) lumen 2000 - 3000, PF> 0.9, THD less 15% diffused connecting with three core flexible copper wire from connector to ceiling rose/angle holder as per existing site requirement including taking down old conventional type tube light fitting as directed by Engr-in-charge. |
| 57 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 3.5 core |
| 58 | Supply of flexible DWC- HDPE pipe (suitable for laying XLPE cables) of nominal diameter 63 mm conforming to IS 16205 part 24, laying the pipe under the ground and drawing the XLPE cable through the DWC pipe including joints, bends etc for proper fixing of the pipe complete all as specified and as directed. |
| 59 | M&L for natural dry river sand cushioning including spreading, levelling and hand punning to underground cable in trench all as specified and directed.Note : Punned thickness shall only be measured and paid. |
| 60 | M&L for sub main wiring but using two single core multistranded PVC insulated copper conductor FRLS Cable of size 2.5 sqmm 1100 volt grade drawn into PVC conduit of size 25 mm dia including 2.5 sqmm. PVC multi standard copper conductor FRLS cable in green colour for continuous earthing including taking down old unserviceable/burnt wiring of any type or size all as directed by Engr-in-Charge.. |
| 61 | Supply and fixing of LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. |
| 62 | Supply & fixing of MCB Distribution board, Triple pole neutral 415 Volt, 4 way, horizontal double door powder coated steel sheet enclosure for surface mounting fitted with 200 Amps bus bar and din channel complete all as directed. |
| 63 | Supply & fixing of MCB TPN, 40 to 100 Amps, ''C'' series 415 Volts, 3 phase, 10 KA capacity all as specified and directed. |
| 64 | Supply & fixing of sheet metal enclosure MCB DB SPN 08 ways double door type with busbar all as specified and directed . |
| 65 | Supply and fixing of amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SPN of 40 Amps current rating complete with connection testing and commissioning. |
| 66 | Supply and fixing of amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SP of 6 to 32 Amps current rating complete with connection testing and commissioning. Please Enable Macros to View BoQ information |