|
| 1 | Dismantling of asbestos cement corrugated, semi corrugated sheeting, any gauge and thickness in roof coverings including Nainital or similar pattern roof covering complete all as specified and as directed. |
| 2 | Dismantling battens for tiles, shingles etc, of any size including tilting fillets spaced exceeding 15cm all as specified and directed. |
| 3 | Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed.Note: The colour and design patten shall be as directed by Engineer-in-charge. |
| 4 | Pre- painted galvalume aluminum zinc coating GI based Plain steel sheet as in ridge of 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering and on chajjas fixed with self tapping screws all as specified and directed. |
| 5 | Mild steel works in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle) including distance pieces, cleats etc.of grade Fe-410-W (Gde-E-250) quality-A all as specified and directed. |
| 6 | Demolition of cement Concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness including floor finishing complete all as specified and directed. |
| 7 | 75mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base floor and finished even and fair complete all as specified and directed. |
| 8 | Machine Pressed precast concrete interlocking paver block rubberised any shape and size conforming to IS- 15658 - 2006 of 60 mm thickness M-35 Grade with grey cement and pigment including 40mm thick sand bed complete all as specified and directed. |
| 9 | Demolition of Brickwork, stone / boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 10 | Pre-cast cement concrete block masnory with solid block using type C1, 1:3:6 using 20mm graded stone aggregate exceeding 10cm in width and setting in mortar 1:6 complete all as specified and directed |
| 11 | Taking down cement or cement lime plaster, any description on brick or stone walls or ceiling, etc.including raking out joints, hacking for key, scrubbing down with water, etc ,complete all as specified and as directed |
| 12 | Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed. |
| 13 | Applying two coats of distemper oil emulsion on ceilings over priming surfaces with alkali resistant priming paint over one coat in 3mm thick putty including preparation of surfaces complete all as specified and as directed. |
| 14 | Taking down chowkhats or frame exceeding 1.5 Sqm but not exceeding 4 sqm each with shutters (without taking off shutters from frame) all as specified and as directed. |
| 15 | Taking down chowkhats or frame not exceeding 1.5 Sqm each with shutters (without taking off shutters from frame) all as specified and as directed. |
| 16 | Factory made UPVC white colour two track panels sliding glazed door made of (big series) frame 67x50mm & sash 46x82mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 Sqm) comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, and upvc extruded line sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (ss 304 grade) body with adjestable double nylon rollers (weight bearing capacity to be 120kg), G.I fasteners 100x8mm size for fixing frame to finished wall and necessary stinless steel screws etc. profile of frame & sash shall be mitred out and fusion welding at all corners, including drilling of holes for fixing hardware's and drainage of water etc. after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specifed and directed.Note: I) Glass or wiremesh shall be measured and paid separatelyII) For UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e depth & width of profile accepted. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 17 | Sheet glass 5.5 mm thick, ordinary quality and glazing with oil putty in squares exc 0.50 sqm in each pane thick of selected quality, fixed to the frame any type all as specified and directed. |
| 18 | Dismantling of floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed. |
| 19 | Vitrified coloured ceramic tiles 10mm thick (square/ rectangular) light shade polished, area of each tiles not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement slurry to match the surface over and including 20mm thick screed bed or bedding layer of mortar in cement mortar 1:4 complete all as specified and as directed. |
| 20 | Vitrified coloured ceramic tiles double charged 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, as in skirting/, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement slurry to match over 10mm thick cement plaster as backing coat in cement mortar 1:4 complete all as specified and directed. |
| 21 | Providing and fixing factory made UPVC white colour Sliding window Three track, Area not exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm ((+) or (-)0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 (+) or (-)0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.Note: (i) The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. (ii) Net Opening will be measured for payment purpose. |
| 22 | Mild steel Framed work such as grill, grating etc with ends of bars shouldered and /or riveted or forged into spikes, framed guard bars, barred iron door, ladders, framed balusters, walk ways, railing, framework of water tanks and simialr work conforming to Fe290 Gde E-165 all as specified and directed. |
| 23 | Preparation of old painted steel surfaces and steel based materials of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed. |
| 24 | Preparation of old painted wooden surfaces and wood based materials of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed. |
| 25 | Complete removal of existing treatment of wall surfaces and applying two coats of Oil Bound Distemper (washable) over a coat of primer (water thinable/ solvent thinable), over one coat of white wall care putty even and smooth complete all as specified and directed. |
| 26 | Complete removal of existing treatment of wall surfaces and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & Fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43litre/10Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10Sqm over new surfaces complete all as specified and directed. |
| 27 | Dismantling boarding/ ceiling board of any description fixed in any position with nails complete all as specified and directed. |
| 28 | Cupboard Shutter / shelf / partition / cabinet care case of required sizes made out of HDHMR Board 18 mm thick one side decorative Lamination & other side Balancing Lamination . The 18 mm thick board shutter / cabinet care case finished at all level including all fixing hardwares and solvent as per the Manufacturers Instructions complete all as specified and directed.Make: Action Tesa or equivalent as approved by GE. |
| 29 | Stainless Steel Auto closing Hinges fixed to Cabinet Shutters complete as per Manufacturers specifications and all as specified and directed.Make : EBCO or Equivalent |
| 30 | Mild steel sheet eaves gutter galvanised class 3 half round with rounded edges 150mm, 1.25mm thick all as specified and directed. |
| 31 | Dismantling wall and ceiling board (fibre, pulp, insulation etc) or insulation boards / slabs / blankets, any thickness, including cover fillets and frame work all as specified and directed. |
| 32 | GI frame work for grid of size 605mm x 605mm seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre / intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2m length) of 0.55 thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and directed. |
| 33 | 12 mm thick Gypsum Board in ceiling fixed with screws as per manufacturers instructions complete all as specified and as directed. |
| 34 | Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M in depth and getting out in soft/ loose soil for laying of under ground cable and foundation of poles.etc complete all as specified and directed. |
| 35 | Returning filling in including spreading, leveling watering and well ramming using excavated soil in layers not exceeding 25 Cm thick, complete all as specified and directed. |
| 36 | Removal of excavated surplus soil to a distance not exceeding 50 m and depositing where directed at al level not exceeding 1.5 m above the starting point and all as specified and directed. |
| 37 | Supply and lay pipe galvanized, \\"Medium class\\", including fittings, accessories like, elbow, bend, union, nipple etc of size 50mm (2\\") dia complete all as speicfied and directed. |
| 38 | Supply and lay pipe galvanized, \\"Medium class\\", including fittings, accessories like, elbow, bend, union, nipple etc of size 20mm (3/4\\") dia complete all as speicfied and directed. |
| 39 | Supply and lay pipe galvanized, \\"Medium class\\", including fittings, accessories like, elbow, bend, union, nipple etc of size 15mm (1/2\\") dia complete all as speicfied and directed. |
| 40 | Gunmetal gate globe valve with iron wheel head screwed both ends for iron pipe and fixed conforming to IS 9338, 50mm (2\\") dia pipe all as specified and directed. |
| 41 | Gunmetal gate globe valve with iron wheel head screwed both ends for iron pipe and fixed conforming to IS 9338, 20mm (3/4\\") dia pipe all as specified and directed. Please Enable Macros to View BoQ information |
| 42 | Gunmetal gate globe valve with iron wheel head screwed both ends for iron pipe and fixed conforming to IS 9338, 20mm (3/4\\") dia pipe all as specified and directed. Please Enable Macros to View BoQ information |
