Tender For Construction Of 100 Bedded New Hostel Building At East Singhbhum, East Singhbum-Jharkhand

TDR : 55101403

Tender Notice
BOQ

17 Days Left

East Singhbum , Jharkhand

Tender Brief : Tender For Construction Of 100 Bedded New Hostel Building At East Singhbhum

Document Fees
₹ 10000 /-

EMD
₹ 469000.0 /-

Tender Value
Refer document

Submission Date
06-05-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 m including all lifts, levelling , ramming the foundation trenches, removing roots of trees, serbs all complete as per approved design,building specification & direction of E/I.
2	Extra for earthwork in hard soil as per specification and direction of E/l (vide classification of soil item-B)
3	ExcavationinOrdinaryRockwith Dozer with lead upto100metres(Excavation for roadway inordinary rock by deploying a dozer,80HP including cutting and pushing the cut earth to site of embankment up to a distance of 100 metres (averagelead50metres) ,trimming bottom and side slopes in accordance with the requirements of lines, grades and cross sections.)
4	Excavation for road work in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and tranporting to the embankment location within all lifts and lead upto 1000 m
5	Providing coarse clean local sand in filling in foundation trenches or in plinth including ramming and watering in layer not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume)
6	Providing designation 75A one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I
7	Providing And Fixing in position cement concrete of specified grade excluding the coast of centering and shuttring -All work up to plinth level .1:2:4 (1 cement :2 coarse sand(Zone-III):4 graded stone aggregate 40mm nominal size)
8	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)
9	Centering and shuttring including,propping etc and removal of from for Foundation,footings below bases of coluumn etc for mass concrete.
10	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:11/2:3 (1 cement :11/2 coarse sand (Zone-III):3 graded stone aggregate 20mm nominal size)
11	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :
12	Centering and shuttring including,propping etc and removal of from for Columns.Pillars,Piers,Abutments,Posts And Struts
13	Reinforced cement concrete work in beams, suspended floors, roofs havingslope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plainwindow sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering,shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarsesand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
14	Centering and shuttring including,propping etc and removal of from for lintel,beams,plinth beam,girders,bressumers and cantilevers
15	Centering and shuttring cluding,propping etc and removal of from for Suspended floors,roofs,landigs,balconyes,and acess platform
16	Centering and shuttring incuding,propping etc and removal of from for Stairs,(excluding landings)excepts spiral staircases
17	Centering and shuttring incuding,propping etc and removal of from for Weather shade, Chajjas, corbels etc., including edges
18	Providing tor steel reinforcement rods as per approved design --do-- tht fe 500(only valid for tata(tiscon),sail, jspl,electeo steel, ltd.bokaro and vizag (RINL)
19	TMTC-500 8mm dia
20	TMTC-500 10mm dia
21	TMTC-500 12mm dia
22	TMTC Fe-500 16mm dia
23	TMTC Fe-500 20/25mm dia
24	Water proofing for old and new roof slab:- providing and laying water proofing treatment on roof slab by appling two component,factory designed ready to use acrylic modified flexible materials applied with …
25	Covering of treated surface with PCC :- Providing 25 mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm
26	Providing and filling of 6 mm thickGroove between 25 mm PCC Panels with Polysulphide Sealant (Poring Grade)as per drawings and technical specifications and direction of E in Charge.(with 18%
27	Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3mmdia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standard drawing.
28	Earth filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)
29	Providing designation 75 A brick work in C.M. (1:4) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.
30	Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.
31	Providing designation 75B brick work in CM (1:6) in Foundation with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.
32	Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).
33	Providing designation 75A brick work in CM (1:6) in superstructure with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.
34	Providing 125mm thick reinforced designation 75A brickwork in C.M. (1:4) in Superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, cost of materials, racking out joints to 15mm depth, carriage, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.
35	Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 and including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I
36	Providing 6 mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I.
37	Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.
38	Supplying, fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.
39	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.
40	Suppling, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l
41	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/clerestory windows & desertory other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulusof elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus sideshall be acceptable but no extra payment on this account shall be made.
42	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/ mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)
43	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Powder coated aluminium (minimumthickness of powder coating 50 micron
44	Providing and fixing reflective glazing in windows with 5mm thick of ST-167-sparkling Ice/ or Equevalant with EPDM rubber / neoprene gasket etc. all cost complete as per architectural drawing and the direction of E/I
45	Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I.
46	Supplying, fitting and fixing 20 guage G.C.I, sheet gate fitted on M.S. Angle frame of size 60x60x6mm. including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l.
47	Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)
48	Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.
49	Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.
50	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
51	Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws win rubber stopper
52	Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.
53	Providing and laying doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc.,complete. Size of Tile 600x600 mm
54	Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete.
55	Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. With commercial grade colour 15X15cm Tiles.
56	Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with floating coat of neat cement, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I (Cost of Cico will be paid separately)
57	Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Udaipur green marble
58	Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
59	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
60	Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l.
61	Providing & Applying high quality acrylic modified resin based textureof Dholpur/Red sand stone Pattern with anti algae and UV resistanceproperties to be applied as intermediate finish in desired pattern @ 43.04kg/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properlycleaning the surface to remove loose particles from the plaster surface,followed by top coating with Premium Acrylic Smooth exterior paint withSilicone additives of required shade by two or more coats @ 1.43 litre/10sqm, complete as the direction of Engineer -in-Charge
62	Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.
63	Providing & fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. Single socketed pipes. 110mm dia
64	Providing & fixing on wall face unplasticised- PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion
65	Bend -110 mm
66	Shoe - 110mm
67	Providing and fixing to the inlet mouth of rain water pipe cast iron grating15 cm diameter and weighing not less than 440 grams.
68	Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge
69	Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).
70	Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approve color design and pattern.
71	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
72	Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.
73	Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete. 150 MM dia R.C.C. pipe 150 mm dia. R.C.C. pipe
74	Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete. 450 mm dia. R.C.C. pipe metre
75	Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm allcomplete
76	Supply fitting and fixing 20mm thick solid core type non decorative double leaf flush shutters in cup borads with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of stadard make with oxidesed iron fittings -do-
77	Supplying & Fixing C.I. Cover without frame -do-do- all complete job
78	Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg
79	Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design :With 20x20 mm Square Bar
80	Making soak pit 2.5 m diameter3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 150 mm Dia
81	Making soak pit 2.5 m diameter3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.
82	Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia
83	Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
84	Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
85	Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750 mm deep, 600 x 450 internal dimension having 250 mm wall thickness in cement mortar ( 1:6 ) including 12 mm cement plaster ( 1:4 ) with punning on inside and cement plaster (1:6) with 600 x 475 mm G.I. cover with frame (Weight not less than 36 Kg.) in foundation and refilling all complete as per specification and direction of E/l.
86	Carriage Of Materials
87	Sand - 10 KM
88	Aggregate - 22 KM
89	Stone Metal - 22 KM
90	Brick- (7+1) KM
91	PLUMBING WORK
92	Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with \\"p\\" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. E.W.C With \\"S\\" trap (b)10 lit. low level P.V.C. cistern
93	Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry hindustan or any other ISS approved make with 100mm HCI p trap 15 litres CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings CI or C C bracket 32mm alkethene / PVC telescopic flush pipe about 2m long with one brass coupling and clamps GI chain and pull including supplying and fixing a pair of vitreous white glazed earthenware footrest to be fixed in floor 15mm CI body brass spindle stop cock of weight not less than 50 grames 15mm PVC connection pipe 450mm long and coat of red oxide primer etc all complete as per specification and direction of E/I. (A) 580 mm long (b) with 12.5 litre low level PVC cistern
94	supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or hindustan or any other I.S.S approved make supported on painted C.I OR R.S bracket 32mm C.I brass waste 15mm dia C.I body brass spindle stop cock of approved quality of weight not less than 350 grames, 32mm PVC wate pipe 750mm long with brass coupling with one end and making plumber joints etc.all complete as per specification and direction of E/I.
95	Providing & fixing stainless steel jali (grating) with hole for waste pipe for floor / nahani trap. 100 mm dia. Weight not less than 100 gms.
96	Supplying, fitting and fixing gun metal full way valve of approved quality all complete as per specifcation and direction of E/I.
97	15mm dia.
98	20mm dia.
99	25mm dia
100	32mm dia
101	Providing and fixing brass stop cock of approved quality all complete as per specification and direction of E/I. … 15mm dia.
102	Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E/I.
103	Pillar cock (long neck)
104	Bib cock - long thread
105	Angular stop cock L.T.
106	Glass shelf
107	Flush valve complete with 32mm size control cock & flange
108	32mm dia. PVC waste pipe 750mm long with cushion
109	Providing Solvent cement
110	Supplying, fitting and fixing C.P. brass towel rail 20mm X 600mm with bracket container
111	Supplying, fitting and fixing C.P. brass soap dish container medium quality with screw and hinges etc.
112	Supplying, fitting and fixing Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror. 600 X 450mm
113	Providing and fixing 15mm dia and 45cm long PVC connection pipe with heavy quality brass coupling at both ends etc all complete as per specification and direction of engineer in charge
114	Providing and fixing PTMT extension nipple 15mm size with 12\\" BSP thread 70mm length and 30mm breadth and weighing not less than 32gms of approved make
115	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e fixing the pipe with clamps at 1Mtr. Spacing. This includes jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the walls etc.
116	20mm nominal bore
117	25mm nominal bore
118	32mm nominal bore
119	External work - 40mm nominal bore
120	Providing & fixing on wall face unplasticised - Rigid P.V.C. pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia
121	Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.
122	Single Tee with door
123	110x110x110 ,mm
124	110 mm bend
125	Supplying and fixing PVC fittings of approved make confirming to IS : 1729 including supplying nails and bobbins, fixing solutions including earth work or masonary work cutting and remaking and providilding as the case may be all complete as per specification and direction of E/I.
126	PVC cowl - 100mm dia.
127	Floor trap - 100mm dia.
128	Ring rubber
129	Door piece
130	ELECTRICAL WORK
131	Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.Group-A
132	Twin Control Point Wiring in PVC Conduit, with Modular type Switch: Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way modular type switch, modular plate, suitable size of GI box etc as required.
133	Power Plug wiring in PVC Conduit (2X4 Sq.mm) :- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor songle core cable in surface/recessed PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required.
134	Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.
135	2x1.5 Sqmm + 1x1.5 sq.mm earth wire(for Single Separate 5A socket from nearest switch board)
136	2x2.5 Sqmm + 1x2.5 sqmm earth wire (for switch board circuit).
137	4 x 4 sq. mm + 2 x 4 sq. mm earth wire (Lighting DB)
138	4x6 Sq.mm + 2x6 Sq.mm earth wire. ( to be used as main for Light TPN DB.)
139	Telephone Wiring in Existing Conduit:- Supplying and drawing, following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required. 2 pair
140	TV cable in Existing Conduit:- Supplying and drawing, co-axial TV cable RG-6 grade copper conductor, PE insulated with PVC sheath in the existing surface/ recessed steel / PVC conduit as required.
141	S/F PVC Conduit: Supplying and fixing of following sizes of Rigid 2 mm thick PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required for TV and TEL out lets. 25 mm
142	S/F Modular type Switch / Socket:- Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required. (to be used in switch board with sockets)
143	1.24.1 5/6 amps, one way switch
144	5/ 6 amps, two way switch
145	l5/ 16 amps, one way switch
146	5/6 amps, 3 pin socket outlet
147	S/F Modular type electronic fan regulator:- Supplying and fixing stepped (two module) type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.
148	S/F Modular blanking plate:- Supplying and fixing of the existing modular plate and switch box excluding modular plate etc, as required.
149	S/F Modular boxes, base and cover plate:- Supplying and fixing following size /modules G.I. box along with modular base and cover plate for modular switches in recess etc. as required
150	6 module (78mm x 205mm x 50mm)
151	8/9 module (78mm x 230mm x 60mm)
152	l2 module (l35mm x 205mm x 60mm)
153	iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
154	S/F light plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 5 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.
155	S/F power plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.
156	S/F Ceiling Rose:- Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.
157	S/F Batten / Angle Holder:- Supplying and fixing batten / angle holder including connection etc as required.
158	Erection on incandescent light fitting :- Erection of wall bracket/ceiling fittings of all sizes and shapes containing upto two GLS amps per fitting, complete with all accessories including connection etc as required.
159	S/F Electonic Musical Call Bell:- Supplying and fixing electronic musical call bell suitable for D.C./A.C. single phase, 230Volts, complete etc as required.
160	ITC fluorescent fitting directly on surface:- Installation, testing and commissioning of Pre-wired fluorescent fitting /compact fluorescent fitting of all types, complete with all accessories and tube etc.directly on surace or ceiling/ wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper conductor, single core cable and earthing etc. as required.
161	ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FRPVC insulated,copper conductor,single core cable etc, as required.
162	ITC Exhaust Fan upto 450 mm sweep:- installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.
163	S/F SP MCB DB:- Supplying and fixing following way, SP&N MCB distribution board of sheet steel for 240 Volts on surface /recess complete with tinned copper bus bar, neutral busbar, earth bar, detachable gland plate, interconnections, phophatized and powder coated painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR).12 Way Double Door
164	S/F TP MCB DB: Supplying and fixing following way,three pole and neutral sheet MCB distribution board, 415 volts on surface/recess complete with tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections,phosphatised and powder painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR). 8 ways (4+24) Double Door. (horizontal type)
165	S/F 'C' series MCB:- Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.
166	6/32A Single Pole
167	40A DP MCB (To use as incomer for all SP MCB DB)
168	50/63A TPN (To use as incommer for all TPN D.B.)
169	P/F MV Danger Notice Plate:- Providing and fixing M.V. danger notice plate of 200mmX150mm, made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in the single red colour on front side as required.
170	Earthing with G.I. Earth plate 600mm x 600mm x 6mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal and salt as required).
171	Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal or cock and salt) complete etc. as required.
172	Providing and fixing 25 mm x 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc, as required.
173	Supplying and laying 25 mm x 5 mm G.I. strip at 0.50 meter below ground as strip earth electrode including connection/termination with G.I. nut, bolt, spring, washer etc, as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm)
174	Providing and fixing 25 mm x 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc as required.
175	S/L 25mm x 6mm G.I. earth strip in ground :- Providing and laying earth connection from earth electrode with 6 SWG dia G.I. wire in 15mm dia G.I. pipe from earth electrode, as required.
176	Providing and fixing 25mm x 5mm G.I. strip on surface or in recess for connection etc. as required.
177	Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required.
178	Providing and fixing 4.00mm dia copper wire on surface or in recess for loop earthing etc, as required.
179	P/F G.I. lightning conductor final - Providing and fixing of lightning conductor final, made of 25mm dia 300mm long, G.I. tube, having single prong at top, with 85mm dia 3mm thick G.I. base plate including holes etc. complete as required.
180	Reverting sweating and soldering of copper/ GI tape ( with other copper GI tape of the finial or any other metallic object) as required
181	iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
182	P/F G.I. lightning conductor tape in horizontal run - Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)
183	P/F G.I. lightning conductor tape in vertical run - Provding and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)
184	P/F Testing joint G.I. lightning conductor - Providing and fixing testing joint, made of 20mm x 3mm thick G.I. strip, 125mm long, with 4 nos. of G.I. bolts, nuts, check nuts and spring washers etc. complete as required.
185	Earthing with G.I. Earth pipe 4.5 mtr long. 40mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal and salt as required).
186	Building Outer Light (90/100W LED) :- Supply of Street lighting luminaire aerodynamically shaped single piece pressure die-cast Aluminum luminaire with high power LEDs as light source and electronic driver (IP65), along with 90/100W LED Lamp, as Energy saving as per drawing prescribed reflector and heat resistant toughened flat glass cover, with 5ft long 40mm dia G.I. pipe with 3 Nos. of iron clamps , anchor nut bolts with double washers as per direction of E/I or consultant as per drawing prescribed reflector and heat resistant toughened flat glass cover (IP-65)Make:- Jaquare / Havells/ Wipro/Baja.
187	Supply of surface mounted round circular ceiling light fixture LED 1x15W-P LED control gear box,electronic blast etc. complete in all respect as required and as per the standard cataloge item.Make:-Jaquare / Havells/ Wipro/Baja.
188	Supply of surface/ pendent mounted with chain Batten type LED 4ft Tube light fitting with Housing & cover made up of CRCA sheet steel. Cover is fixed to the housing by means of 2 Nos. bolt with engineering plastic head along with 1 nos LED tube of 20/22W Each of luminous efficacy of efficacy >110 Lm/W. Make:- Jaquare / Havells/ Wipro/Baja.
189	Supply, Installation, testing and commissioning of following, size ceiling fan 3 Blades confirming to IS : 374 : 2019 including wiring the down rods of standard length (up to 30cm) with 1.5 sq.mm. FR PVC insulated, copper wire suitable for 230V 50Hz, single phase supply etc. complete as required. 1200mm (48\\") BLDC 5star rating 32W Ceiling Fan
190	Supply, fitting and fixing of Special type bulk head fittings complete set with 9W LED. Make:- Jaquare / Havells/ Wipro/Baja.
191	15/16W LED type bulb :- Supply and fixing of 15 led bulb in existin Holder Fitting .Make:- Jaquare / Havells/ Wipro/Baja.
192	Supply of surface/ pendent mounted with suspenssion chain Batten type LED Tube light fitting with Housing & cover made up of CRCA sheet steel. Cover is fixed to the housing by means of 2 Nos. bolt with engineering plastic head along with 2 nos LED tube of 20/22W Each of luminous efficacy of efficacy >110 Lm/W. (Make :- Philips- / Havells / Equivallent in Bajaj / Wipro.).
193	Supply and Transportation of AC 230/250 Volts, 50Hz,300mm sweep Exahaust Fans including providing nuts- bolts, mounting frame and other required accessories etc. (For toilets) Make:- Bajaj /Crompton / Havells .
194	LT PANEL FOR Girl's HOSTEL BUILDING : (For G+2BUILDING) :- Supplying, designing, manufacturing, fitting, fixing, installation, testing and commissioning of LT Panel, fabricated out of 1.6mm thick (16 SWG) CRCA sheet steel IP:43, (dust and vermin proof) with reinforcement of suitable lifting arrangement effecting proper connection of all incomer and outgoing for all DBs , floor mounting type , fixed on base channel of 75mm x 75mm x 6mm, which will have incoming 3 phase power supply from Campus Sub-Station.
195	The sheet steel shall under go minimum of 7 tank treatment followed by finished powder coating of minimum 60 micron thickness and suitable for operation on 415V / 3 Ph / 50 Cy includes 415V electrolitic Al. bus bar with atleast 3 mm removable gland plate, cable glands including connection with outgoing feeders complete in all respect and should have bottom entry.
196	The panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 5/15A socket service outlet (single phase) and 1 no. CFL light with holder shall be provided in one of the compartments as service outlet in the panel. Panel shall be so designed as to have minimum 10% spare feeders/space. The complete panel shall be fuse less type, for control circuits 2A/6A MCB's to be used.
197	The panel shall be interlocked with switchgear in such a way that no door can be opened when the switch is in ON position.The switch gear shall have mechanical arrangement for interlock defeat.The design of panel shall be such as to offer maximun safety and easey of maintenance. The gap between live part of the Panel shall be minimum 35mm.
198	The above Panel shall be completed with 3 Nos. LED phase indicating lamps with MCB protection, analogue ammeter, voltmeter, selector switches, CTs etc. as incomer with all interconnections and compartmentalised cubical type for installing meters with hinged and lockable door stand. All opening shall be covered by soft rubber gasket. All wires used for control circuit should be FRLS PVC insulated flexible copper wire of grade 1100V.
199	The MCCB's shall be Ics = 100% Icu, with rotary handle, spreader links & pad locking arrangement, with trip setting as per load requirement with short circuit & over current protection. The breaking capacity specified is Ics=Icu value. All MCCB's shall be of thermo magnetic category type.
200	AL. BUS BAR:- The panel includes 415V, 400A, 3Ph, 36KA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) G.I. Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The electrolytic Aluminium bus bar of grade 63401 WP as per I:S 5082 of suitable length and insulated by heat shrinkable sleeves Red, yellow, Blue and Black as R Y B & N. The current density of bus bar shall be minimum 0.8 A / sq mm. All inter connections from main Bus Bar to individual MCCB shall be made with 4, 6 & 10 Sq mm FRLS PVC Cu. wire with 35A 4 studs (Brass) treminal block..
201	Each feeder shall have individual compartment with name plate with DB Nos., Floor No. and Block No.
202	Note:- Inspection of LT Panel shall be carried out by Engineering Incharge / Consultant (Eletcrical) at panel builder site and for that, all arragements shall be made by the suppilier on prior information to parrent department.
203	SLD along with the G.A. drawing of LT Panel will be submitted by the contractor to Engineering Incharge or to the Consultant for approval . The above SLD and G.A. Drawing of Main LT Panel must be based on approved SLD.
204	Selection of Make of Switch Gears and other components of Panel shall be decided by the consultant (elec.) / Engineering Incharge)
205	Panel Size - As per Drawing submitted.
206	Cost of Fabcrcation part of LT. Panel & busbar system, in CRCA Sheet Steel enclosure (IP-43) without any components. Name of Panel Builder :- SPC Electrotech Pvt. Ltd. / EAP / PM Control/TTS Systematix Private Ltd./ ADLAK. (A)
207	Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL-or 3 VA
208	Make of MCB- C Series 10kA- Legrand/Schneider/ Siemens/ L&T.
209	INCOMER :-
210	400A FP MCCB (36kA) with adjustable thermomagnetic release type with S/C & O/L protection with extended front rotary handle and spreader links.
211	iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
212	INDICATING FOR PANEL FOR LIFT MACHINE
213	Multi function-meter (0 – 500A) 96mmx96mm 4-position with selector switch for incomer. Make- L& T./ AE/ Schneider. Make- Kaycee/L&T/Schneider.
214	CT 500/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix
215	Phase indicating light shall be protected by 2 Amps SP MCB's for incomer.Make-L& T./ AE/ Schneider.
216	iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
217	OUTGOING
218	100A/ FP/16kA MCCB with thermomagnetic release type with S/C & O/L protection with extended front rotary handle and spreader links -1No.
219	80A/FP/16kA MCCB with thermomagnetic release type with S/C & O/L protection with extended front rotary handle and spreader links. -8 Nos.
220	63A FP MCB C-Series.-4 Nos.
221	32A DP MCB C-Series.-2 Nos.
222	Total Cost of LT Panel for Girl's Hostel
223	iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
224	FLOOR PANEL FOR Girl's HOSTEL BUILDING : (For G+2 BUILDING) :- Supplying, designing, manufacturing, fitting, fixing, installation, testing and commissioning of LT Panel, fabricated out of 1.6mm thick (16 SWG) CRCA sheet steel IP:43, (dust and vermin proof) with reinforcement of suitable lifting arrangement effecting proper connection of all incomer and outgoing for all DBs , floor mounting type , fixed on base channel of 75mm x 75mm x 6mm, which will have incoming 3 phase power supply from Campus Sub-Station.
225	The sheet steel shall under go minimum of 7 tank treatment followed by finished powder coating of minimum 60 micron thickness and suitable for operation on 415V / 3 Ph / 50 Cy includes 415V electrolitic Al. bus bar with atleast 3 mm removable gland plate, cable glands including connection with outgoing feeders complete in all respect and should have bottom entry.
226	The panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 5/15A socket service outlet (single phase) and 1 no. CFL light with holder shall be provided in one of the compartments as service outlet in the panel. Panel shall be so designed as to have minimum 10% spare feeders/space. The complete panel shall be fuse less type, for control circuits 2A/6A MCB's to be used.
227	The panel shall be interlocked with switchgear in such a way that no door can be opened when the switch is in ON position.The switch gear shall have mechanical arrangement for interlock defeat.The design of panel shall be such as to offer maximun safety and easey of maintenance. The gap between live part of the Panel shall be minimum 35mm.
228	The above Panel shall be completed with 3 Nos. LED phase indicating lamps with MCB protection, analogue ammeter, voltmeter, selector switches, CTs etc. as incomer with all interconnections and compartmentalised cubical type for installing meters with hinged and lockable door stand. All opening shall be covered by soft rubber gasket. All wires used for control circuit should be FRLS PVC insulated flexible copper wire of grade 1100V.
229	The MCCB's shall be Ics = 100% Icu, with rotary handle, spreader links & pad locking arrangement, with trip setting as per load requirement with short circuit & over current protection. The breaking capacity specified is Ics=Icu value. All MCCB's shall be of thermo magnetic category type.
230	AL. BUS BAR:- The panel includes 415V, 100A, 3Ph, 16KA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) G.I. Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The electrolytic Aluminium bus bar of grade 63401 WP as per I:S 5082 of suitable length and insulated by heat shrinkable sleeves Red, yellow, Blue and Black as R Y B & N. The current density of bus bar shall be minimum 0.8 A / sq mm. All inter connections from main Bus Bar to individual MCCB shall be made with 4, 6 & 10 Sq mm FRLS PVC Cu. wire with 35A 4 studs (Brass) treminal block..
231	Each feeder shall have individual compartment with name plate with DB Nos., Floor No. and Block No.
232	Note:- Inspection of LT Panel shall be carried out by Engineering Incharge / Consultant (Eletcrical) at panel builder site and for that, all arragements shall be made by the suppilier on prior information to parrent department.
233	SLD along with the G.A. drawing of LT Panel will be submitted by the contractor to Engineering Incharge or to the Consultant for approval . The above SLD and G.A. Drawing of Main LT Panel must be based on approved SLD.
234	Selection of Make of Switch Gears and other components of Panel shall be decided by the consultant (elec.) / Engineering Incharge)
235	Panel Size - As per Drawing submitted.
236	Cost of Fabcrcation part of LT. Panel & busbar system, in CRCA Sheet Steel enclosure (IP-43) without any components. Name of Panel Builder :- SPC Electrotech Pvt. Ltd. / EAP / PM Control/TTS Systematix Private Ltd./ ADLAK. (A)
237	Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL-or 3 VA
238	Make of MCB- C Series 10kA- Legrand/Schneider/ Siemens/ L&T.
239	INCOMER :-
240	80A FP MCCB (16kA) with adjustable thermomagnetic release type with S/C & O/L protection with extended front rotary handle and spreader links.
241	iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
242	INDICATING FOR PANEL FOR LIFT MACHINE
243	Multi function-meter (0 – 100A) 96mmx96mm 4-position with selector switch for incomer. Make- L& T./ AE/ Schneider. Make- Kaycee/L&T/Schneider.
244	CT 100/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix
245	Phase indicating light shall be protected by 2 Amps SP MCB's for incomer.Make-L& T./ AE/ Schneider.
246	OUTGOING
247	63A FP MCB C-Series.-6 Nos.
248	32A DP MCB C-Series.-2 Nos.
249	Total Cost of LT Panel for Girl's Hostel
250	iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
251	Providing and fixing of PVC/XLPE indulated PVC sheathed heavy duty , aluminium armoured cable of grade 1.1KV as per IS 1554 (Part-1), etc. as required. Make:- Havells / Finolex / Polycab/KEI.
252	3.5 Core 35 Sq.mm. XLPE Al. Ar. Cable 1.1kV.
253	Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 1 run of Cable
254	1.1 KV Cable End Termination:-Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required. 3.5 Core 35 Sq. mm. (32mm)
255	Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc. as required. 100 mm dia
256	FIRE FIGHTING WORK Please Enable Macros to View BoQ information
257	FIRE FIGHTING WORK Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Jharkhand Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of 100 Bedded New Hostel Building At East Singhbhum, East Singhbum-Jharkhand

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of 100 Bedded New Hostel Building At East Singhbhum, East Singhbum-Jharkhand

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us