|
| 1 | Excavation in trenches in soft/loose soil for n exe 1.5 mtr in width and not exe 1.5 mtr in depth for foundation etc or for shafts well case pits manhole piers holes etc not exe 10 sqm on plan complete all as specified and directed. |
| 2 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed. |
| 3 | Removing excavated material (soil) n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed. |
| 4 | M&L for PCC 1:4:8( type D-2 using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed. |
| 5 | M&L for PCC 1:5:10 ( type E-2 using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed. |
| 6 | M&L for 75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, and joints shall be sealed with joint sealing compound grade 'A' complete all as specified and directed. |
| 7 | M&L for form work to sides and soffits of floor or roof or lintel beams for rough finished surfaces complete all as specified and directed. |
| 8 | S&F mild steel TMT bars 10mm dia and over cut to length bent to shape required , including cranking bending spirally for hooping for col, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips qty confirming to Fe-410W(Gde- E-250) or Fe-290(Gde-E-165) complete all as specified and directed. |
| 9 | All as per item No 08 here-in-before but 5mm dia & over upto and incl 10mm dia in stirrups, spacers and binders complete all as specified and directed. |
| 10 | M&L for RCC type B1 (1:2:4) (nominal mix) with 20mm aggregate for footing & plinth beam complete all as specified and as directed. |
| 11 | M&L for RCC type B1 (1:2:4) (nominal mix) with 20mm aggregate for floor beams, roof beams. Lintel beams, tie beams, gable beam complete all as specified and directed. |
| 12 | M&L for PCC type B-2 (1:2:4), using 40 mm graded stone aggregates as in filling & mass concrete, sub base, complete all as specified and directed. |
| 13 | M&L for Brick work using Sub class B bricks/Fly Ash lime fuel bricks or as specified in PS-II clause , straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:4), complete all as specified. |
| 14 | M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces with and including WPC, finished even and smooth complete all as specified and directed. |
| 15 | S&F Plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections of grade Fe 410-W (Gde- E- 250) quality- A complete all as specified and directed |
| 16 | S&F Mild steel work as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. quality confirming to grade Fe-290-Gde E-165, complete all as specified and directed. |
| 17 | S&F Mild steel bolts (machine made) with screwed on end with hexagonal or square nuts and washer other end 8-10 mm dia of neck and exc 5 cm long but n exc 10 cm long complete all as specified and directed. |
| 18 | M & L for rendering 15 mm thick on fair faces of brick work or concrete surface finished fair & even in CM 1:6 complete all as specified and directed. |
| 19 | M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamelled paint over one coat of red oxide primer complete all as specified and directed. |
| 20 | S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified etc completed all as specified and directed. |
| 21 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified etc complete all as specified and directed. |
| 22 | M&L for Bitumen blown any grade, applied hot, two coats, to concrete surfaces at the rate of 1.5kg. per sq. m per coat as in Damp proof course including cleaning surfaces etc, complete all as specified and directed. Please Enable Macros to View BoQ information |
