Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Excavation in soil in hilly area all heights and depths, in all kind of soil including saturated soil comprising of pick, jumper, blasting work both in soft and hard rock with chiseling/wedging out of rock (where blasting is prohibited) and their intermediate classification of soil including, dewatering wherever required setting out to the required line grades, side slopes trimming bottom and level as shown on the drawings as directed by Engineer-in-Charge at site according to technical specifications clause 1603.1 & 1603.2 sorting out useful/ unuseful materials and stacking the same in all leads and lift and transportation of un-useful materials for filling in road ways, embankments for grades improvements and levelling to the required grade and then disposing of surplus excavated earth in acquired width of roads or on approved dumping sites through all modes of transportation including head load, animal load or mechanical means along with its levelling fine dressing and all labour, machineries, materials, tools equipments and safty measures and incidentals necessary to complete the work by all means ( if required). Recovery of useful stone of 10.48 cum. @ 300/- per cum. amounting to Rs. 3,144/- only shall be done on prorata basis for the quantity of cutting in earth work effected. Any loss to the public and private property during the course of execution shall be the absolute responsibility of the contractor, which shall have to be duly compensated by him in all respect including all leads and lift of materials as per direction of Engineer-in-charge.The rate is including octroi,royality, Malkana, toll taxes imposed by the Government but excluding GST. |
| 2 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation, trenches, drains (Any width or square meter on plan), including dressing of sides and ramming of bottoms, lift upto any height, including getting out the excavated soil and disposal of surplus excavated soil as directed in all kinds of classification, of soils such as pick work, jumper work, blasting work saturated soils including chiseling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Any loss to the public or private property during the course of excavation shall be the sole responsibility of the contractor which shall have to be duly compensated by him at his own cost in all cases including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 3 | Providing and laying in position cement concrete 1:4:8 (one cement : four coarse sand : eight graded stone aggregate 40mm (forty millimeter) nominal size) excluding the cost of centering and shuttering all work up to plinth level including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (one cement : five coarse sand : ten graded stone aggregate 40mm (forty millimeter) nominal size) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 5 | Providing and laying cement concrete 1:5:10 (one cement : five coarse sand : ten graded stone aggregate 40 mm (forty millimetre) nominal size) in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor all level, excluding the cost of centering, shuttering and finishing including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 6 | Providing and fixing weep holes with 110mm dia (one hundred ten millimetre) PVC pipes laid in slope of 1:20 (one in twenty) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 7 | Providing and laying upto first two level reinforced cement concrete 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size) to give a smooth and even surface including centring and shuttering etc but excluding costof reinforcement in : String courses, copings, bed plates, anchor blocks, plain windows sills and the like including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 8 | Constructing Coursed rubble hammer dressed 'U' shape open surface drain with side wall. 15x22cm (fifteen into twenty two centimeter ) in cement mortar 1:6 (one cement : six approved sand) and inside plastering with cement mortar 1:3 (one cement: three approved sand) including earth work and laying 10cm (ten centimeter ) cement concrete in 1:5:10 (one cement : five approved sand : ten graded crushed stone aggregate) of 40mm (forty millimeter) nominal size and 7.5cm (seven point five centimeter) cement concrete 1:2:4 (one cement : two approved sand : four graded crushed stone aggregate of 20mm (twenty millimeter) nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form work for in setu-reinforced concrete and plain concrete work : |
| 10 | Suspended floors, roofs, landings, balconies and access platform within all leads, lifts and carriage of materials and other incidentals or as per direction and satisfaction of Engineer-in-Charge. |
| 11 | Lintels, beams, plinth beams, girders, bressumers and cantilevers within all leads, lifts and carriage of materials and other incidentals or as per direction and satisfaction of Engineer-in-Charge. |
| 12 | Edges of slabs and breaks in floors and walls up to any width within all leads, lifts and carriage of materials and other incidentals or as per direction and satisfaction of Engineer-in-Charge. |
| 13 | Weather shade, Chajjas, corbels etc., including edges including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 14 | Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.all complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 15 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm (twenty millimeter) nominal size) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 16 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete including cost of binding wire upto all floor level. Thermo-Mechanically Treated bars of grade Fe-500D (five hundred) or more including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 17 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work up to plinth level, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability. (ll) works above plinth level upto Floor -V level. (Note :- Cement content considered in this item is @ 330 kg/cum (three hundred thirty kilogram/cubic metre). Excess/ less cement used as per design mix is payable/recoverable separately) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 18 | Brick work with common burnt clay F.P.S. (Non modular) bricks of class designation 7.5 (seven point five) in super structure above plinth level up to floor V level in all shapes and sizes in cement mortar 1:6 (one cement : six coarse sand) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 19 | Half brick masonry with common burnt clay F.P.S. (Non modular) bricks of class designation 7.5 (seven point five) in foundation, plinth and super structure in Cement mortar 1:4 (one cement : four coarse sand) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 20 | Providing and laying Random Rubble Masonry/Polygonal Rubble Masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement : six sand : twelve graded stone aggregate 20mm (twenty millimeter) nominal size) at plinth level including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 21 | Providing and laying Coursed Rubble Masonry (second sort) with hard stone in foundation & plinth with cement mortar 1:6 (one cement : six coarse sand) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 22 | Providing and laying Boulder filling under floors tightly hand packed including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 23 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, having double groove for fixing double glass unit whereever required , excluding panelling and glass pans which will be paid for separately, all complete as per direction of Engineer-incharge. (Note:- Butt hinges and necessary screws shall be paid separately) Second Class Deodar Wood : 40mm (forty millimeter) thick shutters including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 24 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25mm to 40mm (twenty five into forty millimeter) thick : Particle Board 12mm (twelve millimeter) thick: Pre-laminated particle board with decorative lamination on both sides, Grade I, Type II, IS:12823 marked including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 25 | Providing and fixing ISI marked decorative flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 (three) ply veneering with vertical grains or cross bands and face veneers on both faces of 35mm (thirty five millimeter) thick shutters of Centuary Ply Board/Kit Ply/Green Ply or its equivalent including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 26 | Providing and fixing plastic sheet 3mm (three millimeter) thick on door shutters (Bathroom and W.C. doors) using synthetic rubber based adhesive/ screw etc. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 27 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 28 | Providing 40x5mm (forty into five millimeter) flat iron hold fast 40cm (forty centimeter) long including fixing to frame with 10mm (ten millimeter) diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimeter) 1:3:6 mix (one cement : three coarse sand : six graded stone aggregate 20mm (twenty millimeter) nominal size) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 29 | Providing and fixing 40mm (forty millimeter) special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 30 | Providing and fixing 125mm (one hundred twenty five millimeter) chromium plated brass handles with necessary screws etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 31 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 (ten) as per IS : 1868 (one thousand eight hundred sixty eight), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 32 | 300x16 mm (three hundred into sixteen millimeter) |
| 33 | 250x16 mm (two hundred fifty into sixteen millimeter) |
| 34 | Providing and fixing 250X10mm (two hundred fifty into ten millimetre) aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 (ten) as per IS : 1868 (one thousand eight hundred sixty eight) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 35 | Providing and fixing 125mm (one hundred twenty five millimeter) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 (ten) as per IS : 1868 (one thousand eight hundred sixty eight)) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 36 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 (ten) as per IS : 1868 (one thousand eight hundred sixty eight)) transparent or dyed to required colour and shade, with necessary screws etc. complete. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 37 | Providing and fixing cup board 19mm (nineteen millimeter) thick water proof termite resistant commercial board box including shelves and shutters, the back side cup board / cabinet shall be 8mm (eight millimeter) thick ply and all the cut portions of shelves shall be finished with 6mm (six millimeter) thick hard wood edging. The cut portion of shutters from all sides shall also be finished with 12mm (twelve millimeter) thick hard wood edging. The shutter from out side shall be finished with 1mm (one millimeter) thick Vaneer Ply of approved shade to match with panelling including stainless steel hinges hinges and magnetic catcher with in all accessories etc. complete as per detailed drawing and including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 38 | Steel work welded in built up section/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. in grating frames, guard bar, ladder railing, brackets, gates and similar work including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 39 | Providing and fixing M.S. Channel door, windows frames maufactured from M.S. Channel ISMC 75X40mm (seventy five into forty millimeter) in combination with M.S. flat 40X5mm (forty into five millimetre) and 12X5mm (twelve five millimetre) welded together as per drawing and direction of Engineer-in-charge including hinges jambs bead and if required angle threshold M.S angle 50X25mm (fifty into twenty five millimeter) welded or rigidly fixed by mechanical means with spilt end tails to each jamb including steel butt hinges 25mm (twenty five millimeter) and provision of locking arrangement and shock absorber as specified and applying a coat of approved steel primer after pretreatment of surface complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 40 | Providing and fixing M.S. Channel door, windows Frames maufactured from M.S. Channel ISMC 75X40mm (seventy five into forty millimeter) in combination with M.S. flat 75X5mm (seventy five into five millimeter) welded together as per drawing and direction of Engineer-in-charge including hinges jambs bead and if required angle threshold M.S angle 50X25mm (fifty into twenty five millimetre) welded or rigidly fixed by mechanical means with spilt end tails to each jamb including steel butt hinges 25mm (twenty five millimeter) and provision of locking arrangement and shock absorber as specified and applying a coat of approved steel primer after pretreatment of surface complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 41 | Providing and fixing window shutter have style of Z-section with T-section of 25X15X3mm (twenty five into fiftten into three millimeter) as per drawing complete with fitting and necessary screws and applying a priming coat with red lead paint including fixing glass pans 4mm (four millimeter) thick with glazing clips, putty and scafolding etc. complete as per approved specification/ design for side/top hung windows including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 42 | Providing and fixing window glazing having style of Z-section with T-section of 25X15X3mm (twenty five into fiftten into three millimetre) as per drawing complete with fitting and necessary screws and applying a priming coat with red lead paint including fixing glass pans 4mm (four millimetre) thick with glazing clips, putty and scafolding etc. complete as per approved specification/ design for Fixed Window glazing including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 43 | Providing and fixing wire guage shutter having style of Z-section with T-section of 25X15X3mm (twenty five into fiftten into three millimeter) using galvanised M.S. wire mesh of average width of aperture 1.4mm (one point four millimeter) and nominal dia of wire 0.63mm (zero point sixty three milimeter) for doors, windows and clerestorey window with metal beading of apporved quality and shape section as per drawing complete with fitting and necessary screws and applying a priming coat with red lead paint complete as per approved specification/ design including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 44 | Providing and laying anti skid Ceramic Glazed floor tiles of size 300x300mm (three hundred into three hundred millimeter) (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20mm (twenty millimeter) thick cement mortar 1:4 (one cement : four coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm (three point three kilogram per square meter) including pointing the joints with white cement and matching pigment etc., complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 45 | Providing and fixing Glazed Digital tiles 300x600x8mm (three hundred into six hundred into eight millimeter) thick of approved shade and manufacturer in skirting risers of steps and dado 12mm (twelve millimeetr) thick cement mortar 1:3 (one cement : three sand) and jointed with cement slurry including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 46 | Providing and laying 22mm (twenty two millimeter) thick hydraucally compressed and polished Precast Terrazo tiles of size 30x30cm/40x40cm (thirty into thirty centimeter/ forty into forty centimeter) with graded marble chips of size upto 12mm (twelve millimeter), laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20mm (twenty millimeter) thick bed of cement mortar 1:4 (one cement : four coarse sand) medium shade pigment using 50% (fifty percent) white cement and 50% (fifty percent) ordinary cementincluding carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 47 | Providing and laying Hydraulically compressed and polished Precast Terrazo tiles 22mm (twenty two millimeter) thick with graded marble chips of sizes upto12mm (twelve millimeter), in skirting and risers of steps not exceeding 30cm (thirty centimetre) in height, on12mm (twelve) thick cement plaster 1:3 (1 cement: 3 coarse sand), jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete with tiles of: Medium shades pigment using 50% (fifty percent) white cement and 50% (fifty percent) ordinary cementincluding carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 48 | Providing and fixing Ist quality GRC/ Unistone wall cladding conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12mm (twelve millimeter) thick bed of cement mortar 1:3 (one cement : three coarse sand) and jointing with grey cement slurry @ 3.3kg/sqm (three point three kilogram/ per square meter), including pointing in white cement mixed with pigment of matching shade complete.including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 49 | Providing and laying 25mm (twenty five millimeter) thick Kota stone slab flooring 20mm (twenty millimeter) (average) thick base of cement mortar 1:4 (one cement : four sand) laid over and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as per specification including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 50 | Kota stone 25mm (twenty millimeter) thick slab flooring in treads with Single piece kota stone (upto 2m (two meter) in length) over 20mm (twenty millimeter) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1: 4 (one cement: four coarse sand) including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 51 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.. |
| 52 | Kota stone slabs 20mm (twenty millimeter) thick in risers of steps, skirting, dado and pillars laid on 12mm (twelve millimeter) (average) thick cement mortar 1:3 (one cement : three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 53 | Marble stone flooring with 18mm (eighteen millimeter) thick marble stone per sample of marble approved by Engineer-in Charge, over 20mm (twenty millimeter) (average) thick base of cement mortar 1:4 (one cement : four coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Baroda Green Marble including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 54 | 15mm (fifteen millimetre) cement plaster on the rough side of single or half brick wall of mix 1:6 (one cement : six fine sand) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 55 | Extra for plastering done on moulding, cornices or architraves including neat finish to line and level including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 56 | 6mm (six millimeter) cement plaster of mix 1:3 (one cement : three fine sand) to ceiling and other exposed RCC work complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 57 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 58 | Painting with satin enamel paint of approved brand and manufacturer to give an shade of Asian paint/ Nerolac (two or more coats on new work) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 59 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre (fifty gram per litre), of approved manufacturer, Interor grade of required shade and colour complete, as per manufacturer's specification: Two or more coats on new work including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 60 | Applying priming coats with water thinnable cement primer on wall surface having VOC (Volatile Organic Compound ) content less than 50 grams/litre (fifty gramme per litre) primer of approved brand and manufacture including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 61 | Finishing walls with 100% (one hundred percent) Premium acrylic emulsion paint having VOC less than 50gm/litre (fifty grame per litre) and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/10sqm (one point four three litre per ten square meter) over and including priming coat of exterior primer applied @ 0.90litre/10sqm (zero point nine zero litre per ten square meter) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 62 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10sqm (zero point nine zero litre per ten square meter) over an under coat of primer applied @ 0.75 ltr/10sqm (zero point seventy five litre per ten square meter) of approved brand and manufacture including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 63 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10sqm (Zero point nine zero litre per ten square metre) over an under coat of primer applied @ 0.80 ltr/10sqm (zero point eight zero litre per ten square meter) of approved brand and manufacture including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 64 | Providing and applying white cement based putty of average thickness 1mm (one millimeter), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 65 | Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm (ten millimeter) gap for thermal expansion; all complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 66 | (i) Single socketed pipes. : 110mm dia meter (one hundred ten millimeter) |
| 67 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm (ten millimeter) gap for thermal expansion. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 68 | (II) Bend 87.5° 110 mm (one hundred ten millimeter) bend |
| 69 | (III)110 mm (one hundred ten millimeter) shoe |
| 70 | Providing and fixing 110mm (one hundred ten millimetre) unplasticised -PVC pipe clips of design to unplasticised - PVC rain water pipes by means of 50x50x50mm (fifty into fifty into fifty millimetre) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 ( one cement: four coarse sand) and making good the wall etc. complete. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 71 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. external work including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 72 | 15mm (Fifteen millimeter) nominal bore |
| 73 | 20mm (Twenty millimeter) nominal bore |
| 74 | 32mm (Thirty two millimeter) nominal bore |
| 75 | Making connection of G.I. distribution branch with G.I. main 25mm to 40mm (Twenty five to forty millimeter) nominal bore size by providing and fixing tee, including cutting and threading the pipe etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 76 | Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 77 | Providing and fixing 20mm (twenty millimeter) gun metal gate valve with C.I. wheel of approved quality (screwed end) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 78 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 79 | 15mm (fifteen millimeter) nominal bore |
| 80 | 20mm (twenty millimeter) nominal bore |
| 81 | Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g.elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00(One) metre spacing. This includes the costs of cutting chases and including testing of joints complete concealed work, including cutting chases and making good the wall etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 82 | 2025 (25mm (Twenty five millimetre) OD) Pipe |
| 83 | 1620 (20mm (Twenty millimetre) OD) Pipe |
| 84 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with PVC cistern SLEEK FRESH DUAL FLUSH (starwhite) of Hindware with 100 mm (hundred millimetre) sand cast Iron P or S trap, 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231 (seven thosand two hundred thirty one), with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm (five hundred eighty into four hundred forty millimetre) with integral type foot rests including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 85 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) Cat. no. 20065 of Hindware or its equivelant in white shade with seat and lid, with sleek plus low level white P.V.C. flushing cistern having dual flush system, including flush pipe, with manually controlled device, conforming to 15: 7231, with all fittings and fixtures complete, including cutting and making good the W.C pan with ISI marked white solid plastic seat and lid including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 86 | Providing and fixing wash basin with C.I. brackets, 15mm (fifteen millimeter), 32mm (thirty two millimeter) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin cat. no.Shine C8863 size 505x405x155mm (five hundred five into four hundred five into one hundred fifty five millimeter) of Perryware, Cera, Jaquar, Hindware or its equivalent including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 87 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the each reception of pipes and fittings including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 88 | Providing and fixing Semi rigid pipe 32mm (thirty two millimeter) dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 89 | Providing and fixing 45cm (forty five centimeter) length 15mm (fifteen millimeter) nominal bore uplasticised PVC connection pipe with brass unions including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 90 | P/F Glass shelf 600 mm (six hundred millimetre) long with C.P. Brass bracket and guard rail no. AKP-CHR-35771P of Jaquar or equivalent make fixed with C.P. Brass screws etc complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 91 | Providing and fixing 600x450mm (six hundred into four hundred fifty millimeter) beveled edge mirror of superior glass (of approved quality) complete with 6mm (six millimeter) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 92 | Providing and fixing C.P. brass long nose bib cock Cat no. OPP-15037PM Jaquar or equivalent single control of approved quality conforming to IS standards. 15mm (fifteen millimeter) nominal bore all complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 93 | Providing and Fixing Angular stop cock with wall flange of opel prime no. OPP-15053PM jaquar or equavalent all complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 94 | Providing and fixing Soap dish stainless steel ACN-1131 N of Jaquar or equivalent all complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 95 | Providing and fixing Piller Cock single control No. OPP-15001PM of Jaquar or equivalent complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 96 | Providing and fixing 8mm (eight millimetre) dia C.P. / S.S. Jet with flexible tube upto 1 (One) metre long with S.S. triangular plate to Eureopean type W.C. of quality and make including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 97 | Providing and fixing Toilet paper holder recessed type stainless steel cat. No. AHS-CHR-1553 of Jaquar or equivalent all complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 98 | Providing and placing polyethylene-Aluminium-Polyethelene PE-AL-PE Composite water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 99 | Providing and fixing 15mm (fifteen millimeter) nominal bore ball valve (brass) of approved quality, High or low pressure, with plastic floats complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 100 | Providing and fixing Single Towel Ring square with round flange Cat No. ACN-1121N of JAQUAR/JAL/ESS or equivalent make of superior quality including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 101 | Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 102 | 110mm (One hundred ten millimetre) diametre |
| 103 | 150mm (One hundred fifty millimeter) diameter |
| 104 | Providing and fixing 110mmX90mm (one hundred ten into ninety millimeter) PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 105 | Providing and fixing 110mm (One hundred ten millimeter) diameter PVC door bend with ovalaccess door, insertion rubber washer 3mm (three millimeter) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 106 | Providing and fixing 110mm (one hundred ten millimeter) diametre PVC plain bend ISI marked including fixing with approved adhesive etc. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 107 | Providing and fixing 110mm (one hundred ten millimeter) diameter PVC plain double equal branch ISI marked including fixing with approved adhesive etc. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 108 | Providing and fixing 110mm (one hundred ten millimeter) diameter PVC single equal branch with oval access door, ISI marked insertion rubber washer 3mm (three millimeter) thick bolts and nuts complete including fixing with approved adhesive etc. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 109 | Providing and fixing 110mm (one hundred ten millimeter) diameter PVC plain double equal branch ISI marked including fixing with approved adhesive etc. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 110 | Providing and fixing 110mm (One hundred ten millimeter) diameter PVC collars ISI marked including fixing with approved adhesive etc. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 111 | Providing and fixing 110mm (one hundred ten millimetre) dia PVC Cawl ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 112 | Providing and fixing 110mm (One hundred ten millimeter) diameter PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 113 | Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand) with R.C.C. top slabwith 1:1.5:3 mix (one cement : one and half coarse sand (zone- III) : three graded stone aggregate 20mm (twenty millimeter) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40mm (forty millimeter) nominal size), inside plastering 12mm (twelve millimeter) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm (twenty millimeter) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80cm (ninety into eighty centimeter) and 45cm (forty five centimeter) deep including C.I. cover with frame (Light duty) 455x610mm (four hundred fifty five into six hundred ten millimeter) internal diameter, total weight of cover and frame to be not less than 38kg (thirty eight kilograme) (weight of cover 23kg (twenty three kilograme) and weight of frame 15kg (fifteen kilogramme)) with sewer bricks conforming to IS : 4885 including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 114 | Constructing soak pit 1.20x1.20x1.20 m (one point twenty into one point twenty into one point twenty metre) filled with brickbats including S.W. drain pipe 100 mm (hundred millimetre) diameter and 1.20 m (one point twenty metre) long complete as per standard design including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 115 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality LD-2.5 (two point five) Rectangular shape 600x450mm (six hundred into four hundred fifty millimeter) internal dimention including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 116 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm (fifty millimeter) thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. 60mm (sixty millimeter) thick cement concrete paver block of M-35 (mix design- thirty five) grade with approved colour, design pattern including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charg |
| 117 | Supplying, filling, spreading & leveling coarse sand of size range 1.5mm to 2mm (one point five millimeter to two millimeter), in the recharge pit, in required thicknes over the gravel layer, including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 118 | Supplying, filling, spreading & leveling stone boulders of size range 5cm to 20cm (five centimeter to twenty centimater), in the recharge pit, in required thicknes including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
