|
| 1 | Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 2 | Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B) |
| 3 | Filling in foundation trenches and plinth in layers. Not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 4 | Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 5 | Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 7 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 8 | Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. |
| 9 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) |
| 10 | Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, scaffolding holding raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 11 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 12 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. |
| 13 | providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing Including carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL) |
| 14 | 8mm dia |
| 15 | 10mm dia |
| 16 | 12-20 mm dia |
| 17 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 18 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 19 | Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts |
| 20 | Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flat/ square bar as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.) |
| 21 | Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I. |
| 22 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speeds. |
| 23 | Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R4 series with frame (115mm & above) x (45mm & above) & both glazed and fly screen sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height above 1.8m) |
| 24 | Fixed window / ventilator with mullion / transom. Using R1 series with frame (33mm & above ) x (35mm & above) & mullion (33mm & above) x (50mm & above). (Height upto 0.90 meter) |
| 25 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not lessthan 12.50 kg/sqm) |
| 26 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4mm in both directions with wire of dia. 0.50 mm all complete. With 12 mm mild steel U beading. |
| 27 | Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 28 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 1200 mm |
| 29 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm |
| 30 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of size Size of Tile 1200 x 1200 mm |
| 31 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab upto 0.50 sqm |
| 32 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work |
| 33 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 34 | Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I. |
| 35 | Providing & Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04 kg/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with Premium Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litre/10 sqm, complete as the direction of Engineer -in-Charge. |
| 36 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification) |
| 37 | Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , specification and direction of E/I. |
| 38 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board. |
| 39 | Carriage of Materials |
| 40 | Sand Lead 8 Km |
| 41 | Brick Lead 8 Km |
| 42 | Stone & Chips Lead 22 Km |
| 43 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall |
| 44 | 15 mm nominal dia. Pipes. |
| 45 | 20 mm nominal dia. Pipes. |
| 46 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. |
| 47 | 15 mm nominal dia .Pipes. |
| 48 | 20 mm nominal dia .Pipes. |
| 49 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 50 | Single tee with door 75x75x75 mm |
| 51 | Single tee with door 110x110x110 mm |
| 52 | Single tee without door 75x75x75 mm |
| 53 | Single tee without door 110x110x110 mm |
| 54 | Bend 87.5° 75 mm bend |
| 55 | Bend 87.5° 110 mm bend |
| 56 | Supplying materials and labours for construction inspection chamber of designation class 75 B bricks size 750 mm deep, 600 x 450 internal dimension having 250 mm wall thickness in cement mortar ( 1:6 ) including 12 mm cement plaster ( 1:4 ) with punning on inside and cement plaster (1:6 ) with 600 x 475 mm G.I. cover with frame (Weight not less than 36 Kg.) along with earth work in Excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/l. |
| 57 | Point wiring in PVC conduit with modular type switch:- Wiring for light point /fan point /exhaust fan point /call point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch ,modular plate, suitable size G.I. box etc.as required. Group B |
| 58 | Twin control point wiring in PVC conduit with modular type switch:- Wiring for twin control light point witch 1.5sq.mm FR PVC insulated copper conductor single core in surface/recessed PVC CONDUIT, 2 way modular, type switch, modular plate, suitable size G.I. box etc .as riquied. |
| 59 | power plug wiring in PVC conduit(2x4sq.mm):-wiringfor light power with 2x4 sq mm FR PVC insulated copper conductor single core in surface/recessed PVC conduit along with 1 Nos. 4 sq. mm FR PVC insulated copper conductor singl core cable for loop earthing as requied. |
| 60 | Circuit/submain wiring in PVC conduit:- Wiring for circuit/submain wiring along with earth with following sizeg FR PVC insulated copper conductor,single core cable in surface/recessed PVC conduit as requied. |
| 61 | 2x1.5sq mm+ 1x1.5sq mm earth wire |
| 62 | 2x2.5sq.mm+1x2.5sq.mm earth wire |
| 63 | 2x6.0sq.mm+1x6.0sq.mm earth wire |
| 64 | 4x10sq.mm+2x6sq.mm earth wier |
| 65 | S/F Modular type switch/ socket :-Supplying and fixing of following modular switch / soket on the existingmodular plate & switch box including connections but excluding modularplate etc. as required. |
| 66 | 5/6amps,one way switch |
| 67 | 15/16 amps, one way switch |
| 68 | 5/6 amps,3 pin socket outlet |
| 69 | 15/16 amps, 6 pin socket outlet |
| 70 | S/F modular type electronic fan regulator :- sfpplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc,as required. |
| 71 | S/F modular type blanking plate :- supplying and fixing modular blanking plate on the existing modular plate and switch box excluding modular plate as required. |
| 72 | S/F modular boxes ,base & cover plate :- supplying and fixing following size/ modules G.I. box along with modular base & cover plate for modular switches in recess etc as required |
| 73 | 1 or 2 module (78mmx78mmx45mm) |
| 74 | 6 module (78mmx205mmx50mm) |
| 75 | S/F Power plug point with Modular type accessories :-supplying and fixing suitable size G.I. box with moudular plate and cover in front on surfesh or in recess including providing and fixing 6 pin, 15/16 mps moudular socket outlet and 15/16 mps modular type switch connection, painting etc. us rquoired. |
| 76 | S/F ceiling roase:- suppliying and fixing 2 pin mps. Ceiling roase on the existing juction box/woon bolck including connection etc. as required |
| 77 | ITC ceiling fan:- Installtion, testing and sonnissoning of ceiling Fan including wiring the down rods of standard length (op to 30cm) with 1.5 sq.mm FR PVC insulated. Copper conducotr, single core cable etc. as required. |
| 78 | ITC exhaust fan upto 450 mm. swee:- Installation of exhaust fan op to 450 mm. sweep in the existing opening, including making the hole to suit the size of the above commissioning etc as required. |
| 79 | S/F s.p. MCB DB:supplying and fixing following way single pole neutral sheet, Steel MCBdistribution board,240 volts,on surface/recess,completewith tinned copper busbar,neutral busbar,earth bar,din bar, interconnection, powder painted including earthing etc asrequierd.(But without MCB/RCCB/lsolator) |
| 80 | 12way Double door |
| 81 | 16way Double door |
| 82 | S/F s.p. MCB DB:supplying and fixing following way horizontal type three pole neutral sheet, Steel MCBdistribution board,415volts,on surface/recess,completewith tinned copper busbar,neutral busbar,earth bar,din bar, interconnection, powder painted including earthing etc asrequierd.(But without MCB/RCCB/lsolator) |
| 83 | 6way(4+18),Double door,Horizontal type |
| 84 | 8way(4+24),Double door,Horizontal type |
| 85 | S/F 'c' series, S.P. MCB:-Supplying and fixing 6 Amps to 32 amps Rating ,240 volts, 10k.A'c' Curve ,miniature circuut breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections,testing and commissioning etc.asrequied. |
| 86 | 6/32amps, single pole |
| 87 | 40amps, DP |
| 88 | 50/63 amps,TPN |
| 89 | S/F SP MCB blanking:- supplying and fixing single pole blanking plate in existing MCB DB complete etc.as required. |
| 90 | S/F SPN RCCB:- supplying and fixing following rating,double pole (single phase and neutral)240 volts,residualcurrent circuit breaker (RCCB),having asensitivity current upto300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc.as required.63amps |
| 91 | S/F 20amps SPN MCB industrial socket outlet:- supplying and fixing 20amps,240 volts,SPN industrial type,socketoutlet,with 2pole and earth,metal enclosed plug top along with 20amps 'c' curve,SP MCCB,in sheetsteel enclosuer,on surface or in recess with chainedmetal cover for the socket outletand complete with connections,testing and commissioning etc.as required. |
| 92 | P/F M.V.danger notice plate:- providing and fixing M.V danger noticeplate of 200mmx150mm,made of mild steet,at least 2mm thick, and vitreous enamelled white on both sides,and with inscrition in single red colour on front side as required. |
| 93 | G.I. Earth pipe eletrode with salt/charcoal:-Erthing with G.I erth pipe 4.5 mtr long,40mm dia inculuding accessories,and providing masonare enclosure with cover plate having locking arrangment and watering pipe etc.with charcoal and salt as required. |
| 94 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below groundas strip earth electrode, including connection/ terminating with G.I. nut, bolt,spring, washer etc. as required. (Jointing shall be done by overlapping andwith 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 95 | Supply Installation, testing and commissioning of follwing size ceiling fan 3Blades confirming to13:374,.2019 including wiring the down rods ofndard length (upto 30cm) with l.Ssq.mm. FR PVC insulated, copper wireuitable for 230V 50H2, single phase supply etc. complete as required.1200mm (48\\") BLDC 5star rating 32W Ceiling Fan |
| 96 | ceiling fan 48\\" (1200mm) BLDC Sstar 15:374:2079 |
| 97 | SITC of 230 mm (9\\") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply completewith motor, louvers/shutters etc. complete as required. Make :- Polar/Usha/Crompton / Havells. |
| 98 | SITC of following rating recess/surface mounted LED round/square shape Down Light Luminarie with pressure die-cast housing for single phase supply voltage. Luminarie shall be confirm to IS; 10322 part-5/section-2 or IEC 62722 with all necessary accesoreies as required. |
| 99 | 12 W Round Surface Down light |
| 100 | 15/16 W Square Surface Down light |
| 101 | 15W COB based round LED light with multiple bem angles (36 Degree) |
| 102 | 30W COB based round LED light with multiple bem angles (36 Degree) |
| 103 | SITC of LED 2 ft Mirror light with power 8/10W, rated voltage 230W, 50 HZ, aluminium /PC body with runninglife minimum 30000 hrs. ( LM 79 and LM 80 reports need to be submitted) |
| 104 | SITC of 4 to 6Watt LED Foot Lamp/LED Step Light cast alluminium body and IP-54, protection |
| 105 | Building Outer Light (45/48W LED) :-Supply, fitting, fixing and testing of building outer lighting luminaire aerodynamically shaped single piece pressure die-cast Aluminum luminaire with high power LEDs as light source and electronic driver (IP65), along with 45/48W LED Lamp, as Energy saving as per drawing prescribed reflector and heat resistant toughened flat glass cover, with 5ft long 40mm dia G.I. pipe with 3 Nos. of iron clamps , anchor nut bolts with double washers as per direction of E/I or consultant as per drawing prescribed reflector and heat resistant toughened flat glass cover (IP-65) and in compliance to IEC Safety Standards. LM 79 and LM 80 reports to be submitted with all accessories. Make:- Havells/Philips- Signify/Bajaj/Jaquar Make 0f LED :- Philips/Osram/Cree/Nichia. |
| 106 | Supply fitting and fixing of PVC/XLPE insulated PVC sheathed heavy duty Al. armoured cable for workingvoltage up to and including1100 Volts confirming to IS 1554 (part-1)Make:- Havells, KEI, Finolex, Polycab. |
| 107 | 3.5 Core 25 Sq. mm |
| 108 | 3.5 Core 120 Sq. mm |
| 109 | 1.1 KV Cable End Termination:-Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade asrequired. |
| 110 | 3.5 Core 25 Sq. mm. (28mm) |
| 111 | 3.5 Core 150 Sq. mm. (50mm) |
| 112 | S/F light plug point with modular type accessories :-Supplying and fixing suitable GI box with modular plac and cover in fronton surface of in recess, including providing and fixing 3 pin 5/6 ampsmodular socket outlet and 5/6 amps modular switch. corutection, paintingetc. as required (For light plugs to be used in non residential buildings) |
| 113 | Installation of stone coated metal roof tile of 0.55 mm thickness, Raw tile Size is 1340 mm x 420 mm , exposure Size is 1290mm x 420 mm in Desired Shade and colour with all hardware and accessories do all complete job As per direction of EI. |
| 114 | Installation of UPVC Gutter size of 300 mm height and have a top opening of 300 mm thickness of UPVC profile is 2.5 mm do all complete job as per Direction of EI |
| 115 | Providing and fixing Door and Window Chokhat panelling 12 mm thick water proof Century Marine ply IS:710, ISI Mark, Termites proof. 1.5mm laminated sheet all complete as per building specification and direction E/I(Make of Laminate and Plywood(710 Marine Grade) Green/Century/Archid or equivalent as per direction of engineer in Charge) |
| 116 | Providing and fixing door shutter of total 50 mm finish wooden framed by both side best quality ply and 1.25 mm thick water proof laminate both side pasting finishing with all material and labour all complete (including all fancy type fitting Branded Mortise Lock Latch butts hings ) as per building specification and direction of E/I. (Make of Laminate, Plywood and Veneer (710 Marine Grade) Green/Century/Archid or equivalent as per direction of engineer in Charge) |
| 117 | Installation of Wall Hung WC With UF Soft Close Seat Cover, Hinges, Accessories Set, Size: 360x585x415 mm OPS-WHT-15951UF |
| 118 | Installation of cistern Single Piece Concealed Cistern Body (Front or Top Actuation) with Floor Mounting Frame, Installation Kit and“P-Type” Drain Pipe Connection Set for Wall Hung WC (without Flush Control Plate) JCS-WHT-2431FP |
| 119 | Jaguar 2 way bib cock antique chrome 35041 m |
| 120 | installation of Jaguar Anti Chrome Health Faucet ACR-573 |
| 121 | Jaguar vitreous China sinks /wash basin KUS-WHT-35901Description : Table Top Basin, Size: 595x435x185 mm |
| 122 | Waste coupling ALD-GDS-705L130DescriptionWaste Coupling 32mm Size Full Thread with 130mm height |
| 123 | Tall boy ALI-ABR-85005BDescriptionSingle Lever Tall Boy with 125mm Extension Body Fixed Spout without Popup Waste System with 600mm Long Braided Hoses |
| 124 | Connection Pipe With Nuts reputed brand |
| 125 | Jaguar Towel Ring antique chrome 1121N |
| 126 | Jaguar Tumbler Holder antique chrome 1141N |
| 127 | Jaguar paper Holder antique chrome 1141N |
| 128 | jaguar control plate antique chrome 852415 |
| 129 | SWIVEL MIRROR 630 X 445MMAKP-CHR-35795 Description Swivel Mirror 630 X 445mm Rectangular Shape |
| 130 | Installation of Geyser Jaguar 25 Litre ERM-WHT-V025 |
| 131 | Lavish Vanity Cabinet 600 m wall hanging single made by Waterproofing material with minimum 5 year warenty do all complete job |
| 132 | SITC of URS-WHT-13267SUrinal With Sensor Kit, Spreader And Fixing Accessories Set, Size:360X350X710 mm |
| 133 | Add 18 % GST (in Basic Rate must fill 12) |
| 134 | Add 1% Labour Cess (in Basic Rate must fill 1) Please Enable Macros to View BoQ information |
