|
| 1 | Excavation in foundations, trenches etc.in all kind of earth including their intermidate classification such as Pick work,jumper work.Blasting work,soft rock including chieling/welding cut of rock where blasting is prohibited,soft rock or hard rock,including bailing/pumping out water wherever possible/required by the Engineer -in-Charge from the edge of excavtion & then returncked soil in 15cm. layers,when required into plinths sides of foundations etc. consolidating each deposited layerby ramming & watering & then deposing of all surplus excavted earth in all leads & lifts including to the dumping site as will be decided by the Engineer -in-Charge. |
| 2 | Providing form work with steel plates 3.15mm(three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in foundation, footing, basis of column etcetra . and mass concrete complete as per HP.PWD. Specifications, approved drawings, designs and entire satisfaction and directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidentals. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 3 | Providing and laying cement concrete 1:4:8 (One cement: Four sand :Eight graded cursed/broken stone aggregate 40mm) (forty millimeters nominal size) mechanically mixed and curing complete, excluding cost of form work in foundation and plinth including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-charge. |
| 4 | Providing and laying cement concrete 1:1.5:3 (one cement into one point five sand into three crushed stone aggregate 20mm. (Twenty millimeter) nominal size) mechanically mixed and vibrated, curing complete excluding cost of form work and reinforcement for reinforced concrete work and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge in Foundation, footings bases of columns etc. and mass concrete. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. |
| 5 | Providing Tor steel reinforcement of TATA Tiscon/SAIL/Rashtria Ispat incluiding cost of binding wire for R.C.C. work including cutting, bending, binding and placing in position complete in all floor levels in all heights including carriage of materials through all modes of transportations with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-Charge.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. |
| 6 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of materials in all leads and lifts. |
| 7 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) including carriage of materials in all leads and lifts. |
| 8 | Stone soling properely hand packed filling interstics with spalls and consolidating with power road roller to the requested gradient and camber including spreading watering and rolling of binding materials moorum or earth etc. complete as per HP.PWD specification. 100mm spread thickness (finished work including materials and labour). including carriage of materials in all leads and lifts. |
| 9 | Providing and fixing angle iron doors frames (single Rebate) manufectured from MS angle section of 35x35x4mm and MS Flat 50x5mm as perdesign and Drawing including Jambs, LockJambs beeds if required angls threshold of MS angle 50x5mm welded or ridigly fixed by mechinical means lugs with spilt endstails to each Jambs including steel butt hinges 2.5mm thickwith a provision of locking arrangements and shockabsorvres as specified and a applying coat of approved steel primer after per- Treatment of the surface as directed by the Engineer- in- Charge. |
| 10 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:. including carriage of materials in all leads and lifts. |
| 11 | Providing and fixing steel glazed doors,windows and ventilators of standerd rolled steel sections ,joints mitred and welded with 16x3.15 mm lugs 10 cm.long embedded in cement concrete blocks 15 cmx10cmx10cm size of 1:3:6(1cement: 3 sand: 6 graded stone aggregate 20mm nominal size)or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fittings, including providing and fixing of glass panes with glazing clips and special metal sesh putty of approved make complete including applying a priming coat of red lead paint. . including carriage of materials in all leads and lifts. |
| 12 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm . including carriage of materials in all leads and lifts. |
| 13 | roviding and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm . including carriage of materials in all leads and lifts. |
| 14 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : . including carriage of materials in all leads and lifts. 100mm |
| 15 | Providing and laying Duro stone vetrified tiles (300x300mmx10mm) in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete. 300*300*10mm . including carriage of materials in all leads and lifts. |
| 16 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge. |
| 17 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.In gratings framed guard bars, ladders, railling,brackets and similar works. including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge. |
| 18 | Providing and fixing 0.60mm thick prepainted steel sheet of TATA Durashine in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia metre with prepainted limpet and rubber washers complete with all accessories as required as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge. |
| 19 | Providing and fixing M.S. BP Sheet 1.66 mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) |
| 20 | P/F Wall panneling with MDF board prelaminated (BOTH SIDE ) termite proof 8 mm thick on soft wood frame work of 1.5\\" x1.5\\" (wood should be coated primer paint ). The grading of MDF should be ISO/ISI certified, with making extra grove on the surface i/c polishing, finishing etc. completely fixed by means of nails/screws/rawl plugs etc. complete as per direction of engineer in charge (Area shall be measured as per total surface area i/c all wastage and cutting etc.) including entire carriage of materials within all leads & lifts. |
| 21 | Providing and Fixing Plain / Perforated 4/6 E- Board False Ceiling of size 1200x600x600mm Frame work with Everest Grid System with main runner 39x24.7mm cross Tee 29x24.7mm & wall angle 222x22.00mm incuding cutting and fixing complete as per HP.PWD specification including carriage of material within all leads and lifts as per direction of Engineer-in-charge. |
| 22 | Painting two coats (excluding priming coat) on new steel and other metal surfaces with readymixed paint acid resisting brushing to give an even shade including cleaning of all dirt,dust and other foreign matter. |
| 23 | Providing and fixing to wall ceiling and floors CPVC pipe fitting and clamps including making good the wall ceiling and floors ISI marked as per HP.PWD specification, (a) 20mm nominal outer dia pipes. |
| 24 | Providing and fixing various capacity.store well branded ISI marked Polythene water tank with 40 (Forty) millimetre nominal size bore galvanized Mild Steel scour tube with fitting 25 (Twenty Five) millimetre nominal bore galvanized Mild Steel overflow tube with fittings and mosquito proof coupling of approved municipal design 15 (Fifteen) millimetre nominal size ball valve and mosquito proof PVC cover with locking arrangement including providing pads of size as required for inlet and outlet tube complete ISI marked as per HP.PWD specification (a) 1000 litres net capacity tank |
| 25 | Providing and fixing PVC Supreme or its equivalent, waste and ventilating pipes jointed properly with solution approved adhesive complete, as per HP.PWD specification, (a) 110 (One hundred ten) millimetres nominal size. |
| 26 | Providing and fixing PVC Supreme or its equivalent, waste and ventilating pipes jointed properly with solution approved adhesive complete, as per HP.PWD specification (b) 75 (One hundred Fifty) millimetres nominal size. |
| 27 | Providing and fixing PVC holder bat clamps of approved design PVC pipes embedded in and including cement concrete blocks 10*10*10cm (ten into ten into ten centimeter) of 1:2:4 (one cement isto two sand isto four graded stone aggregate 20mm (twenty millimeter) nominal size) and cost of cutting holes and making good the wall etc. as per HP.PWD specification (a) 110 (One hundred ten) millimetres nominal size. |
| 28 | Providing and fixing PVC holder bat clamps of approved design PVC pipes embedded in and including cement concrete blocks 10*10*10cm (ten into ten into ten centimeter) of 1:2:4 (one cement isto two sand isto four graded stone aggregate 20mm (twenty millimeter) nominal size) and cost of cutting holes and making good the wall etc. as per HP.PWD specification(b) 150 mm (One hundred fifty milimeter nominal size. |
| 29 | Providing and fixing PVC ISI marked floor traps of self-cleaning design including fixing with approved adhesive complete including cost of cutting and making good the walls and the floors: as per HP.PWD specification, (a) 110x 90 mm(one hundred ten into ninety milimeter. |
| 30 | Providing and fixing PVC single equal branch with oval access door , ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete.(a) 110 (One hundred ten) millimetres nominal size. |
| 31 | Providing and fixing PVC single equal branch with oval access door , ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete (b) 75 mm(seventy five milimeter nominal size. |
| 32 | Providing and fixing PVC door bend with oval acces door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete (a) 110 mm dia |
| 33 | Providing and fixing PVC door bend with oval acces door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete(b) 75 mm dia |
| 34 | Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete. (a) 110 mm dia |
| 35 | Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete.(b) 75 mm dia |
| 36 | Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete.(a) 110 mm dia |
| 37 | Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete. (b) 75 mm dia |
| 38 | Providing and fixing PVC 'P' or 'S' trap for water closet ( squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete.(a) 110 mm dia |
| 39 | Providing and fixing PVC cowl including carriage of materials within all leads and lifts :- (a) 110 mm dia |
| 40 | Providing and fixing PVC cowl including carriage of materials within all leads and lifts :- (b) 75 mm dia |
| 41 | Providing and fixing viterous China water closet squatting pan (Indian Type W.C. pan) size 580mm (Earth work, bed concrete, foot rest and traps to be measured and paid for separately (a) Orrissa pattern long pattern |
| 42 | Providing and fixing 10.00 ltr.capacity PVC low level duel flushing cistern CERA catlogue No. 2603 or equivalenet with a pair of brackets with fittings such as lead valve, less syphon, 15mm nominal size PVC ball valve with polythene float, PVC handle, union and coupling for connection with inlet, outlet and overflow pipes 40 mm dia PVC flush bend with cistern and closet & over flow pipe to be paid for separately) |
| 43 | Providing and fixing viterous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fitting including carriage of materials within all leads and lifts :- (i) Flat back :- (a) 550 X 400 mm |
| 44 | Providing and fixing C.P. brass waste (heavy duty ISI marked IS:8931 & 8934) for wash basin or sink including carriage of materials within all leads and lifts :- (a) 32 mm dia |
| 45 | Providing and fixing MI union for wash basin or sink 32 mm dia including carriage of materials within all leads and lifts |
| 46 | P/F 32 mm dia lead waste pipe for wash basin including carriage of materials within all leads and lifts |
| 47 | Providing & fixing 100mm dia C.P. grating for floor or nahani/gully/floor trap including carrage of material within all leads and lifts:- |
| 48 | Providing and fixing 600mmx450mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washer including carriage of materials within all leads and lifts :- |
| 49 | Providing and fixing charomium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws including carriage of materials within all leads and lifts :- |
| 50 | Providing and fixing CP brass bib tap (heavy duty ISI marked IS:8931 & 8934) of jaquar with capstan head including carriage of materials within all leads and lifts :-15mm dia :- |
| 51 | Providing and fixing CP brass pillar tap of jaquar with capstan head (heavy duty ISI marked IS:8931 & 8934) including carriage of materials within all leads and lifts :-15mm dia :- |
| 52 | Providing and fixing C.P.brass angle valve of jaquar (heavy duty ISI marked IS:8931 & 8934) including carriage of materials within all leads and lifts :-15mm dia :- |
| 53 | Providing and fixing PVC connection pipe (heavy duty ISI marked IS:8931 & 8934) with brass union including carriage of materials within all leads and lifts :-45cms length :- 15mm nominal bore :- |
| 54 | Providing and fixing brass full way valve with wheel including carriage of materials within all leads and lifts :- 20mm nominal bore :- |
| 55 | Providing and fixing CP or PTMT jet spray with 1 m tube of approved quality and colour |
| 56 | Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit with modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. |
| 57 | Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing asrequired..2x1.5 Sq. mm |
| 58 | Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required:- Exhaust Fan, Light duty, (Domestic) 300 mm sweep |
| 59 | Providing and installation of following type of ultra slim decorative LED batten with extruded aluminium heat sink, with anti glare polycarbonate diffuser and energy efficient constant current, integral electronic driver; suitable for input voltage: AC 220-240 V, 50/60Hz, complete with all accessories, including mounting clips & loop in loop out wire, connections, testing and commissioning etc. as required. Make: Philips, Syska, GE, Bajaj, C&S, Panasonic or any other approved by Engineer-in-Charge.Led tube 20 watt |
| 60 | Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:- Double door-8 way |
| 61 | Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required:- Double pole. Cat-A. |
| 62 | Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required:-Single pole. Cat-A. |
| 63 | Supplying and fixing of Service wire 6mm |
| 64 | Supplying & fixing metal box of 180mmx100mmx60mm deep (nominal size) on surface/ recess with suitable size phenolic laminated sheet cover in the front including providing & fixing 56pin 15/16 ampere socket outlet and 15/16 amperes, piano type switch, connections, painting etc. as required. Please Enable Macros to View BoQ information |
