|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kind of soil |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, with all lead and lift. All kind of soil |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of material in all leads & lifts. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level including carriage of material in all leads & lifts. |
| 5 | 1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size) |
| 6 | 1:5:10 (1 cement : 5 coarse sand) : 10 graded stone aggregate 40 mm nominal size) |
| 7 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of material in all leads & lifts. |
| 8 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer- in-charge including carriage of material in all leads and lifts. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level |
| 9 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer- in-charge including carriage of material in all leads and lifts. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works above plinth level upto floor V level |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form including carriage of material in all leads and lifts. |
| 11 | Foundations, footings, bases of columns,etc. for mass concrete |
| 12 | Suspended floors, roofs, landings, balconies and access platform |
| 13 | Lintels, beams, plinth beams, girders,bressumers and cantilevers |
| 14 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 15 | Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards |
| 16 | Weather shade, Chajjas, corbels etc., including edges |
| 17 | Edges of slabs and breaks in floors and walls |
| 18 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. including carriage of materialin all leads and lifts. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 19 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : including carriage of materialin all leads and lifts. Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 20 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer including carriage of material in all leads & lifts. Using M.S. angels 40x40x6 mm for diagonal braces |
| 21 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete including carriage of material in all leads & lifts. Fixed to openings /wooden frames with rawl plugs screws etc. |
| 22 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes i/c carriage of material in all leads and lifts. 110 mm diameter |
| 23 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion i/c carriage of material in all leads and lifts |
| 24 | Bend 87.5° 110 mm bend |
| 25 | Shoe (Plain) 110 mm Shoe |
| 26 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete i/c carriage of material in all leads and lifts 110mm |
| 27 | 6 mm cement plaster to ceiling of mix 1:3 (1 cement : 3 fine sand) including carriage of material in all leads and lifts. |
| 28 | 15 mm cement plaster on the fair side of single or half brick wall of mix 1:6 (1 cement: 6 fine sand) including carriage of material in all leads and lifts. |
| 29 | 20 mm cement plaster on the rough of single or half brick wall of mix 1:6 (1 cement: 6 fine sand) on rough side wall including carriage of material in all leads & lifts. |
| 30 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete .including carriage of material in all leads and lifts. |
| 31 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives New work (Two or more coats applied @1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.including carriage of material in all leads and lifts. |
| 32 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat withcement primer including carriage of material in all leads and lifts. |
| 33 | On Wall |
| 34 | On Ceiling. |
| 35 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications including carriage of material in all leads & lifts. Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture |
| 36 | Providing and fixing 10 mm thick anti skid, acid or alkali resistant vertified tiles of any size & any colour of approved make acid and/or alkali resisting mortar bedding, and joints filled with epoxy grouting with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge including carriage of material in all leads & lifts. In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Anti skid,Acid and alkali resistant tile |
| 37 | Providing and fixing 10 mm thick anti skid, acid or alkali resistant vertified tiles of any size & any colour of approved make acid and/or alkali resisting mortar bedding, and joints filled with epoxy grouting with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge including carriage of material in all leads & lifts. In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile |
| 38 | Providing and laying 10 mm thick Vitrified tiles in flooring of appproved make of any colour and size with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, In flooring over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement ,or epoxy grouting & matching pigments etc. complete i/c cutting the tiles wherever required including carriage of material in all leads &lifts. |
| 39 | Providing and laying Vitrified tiles of appproved make of any colour and any size ( with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints with epoxy i/c cost for cutting the tiles whwrever required, including carriage of material in all leads & lifts. Please Enable Macros to View BoQ information |
