|
| 1 | NOTE:-(i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates.(ii) It is highlighted that the certain condition of General Condition of Contracts (IAFW-2249) has been modified as per direction of MoD i.e. inclusssion of Performance Security, deletion of Risk & Cost Provisions and increase in defect liability period all as per tender documents. The tenderers should keep in mind while quoting their offer. (iii) (Applicable for all items/parts):- The bidders/contractors are advised to refer Notes on BOQ/SCH'A' before entry/quoting the rates. |
| 2 | Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillers etc complete all as specified and as directed. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 4 | Dismantling plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and as directed. |
| 5 | Dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed. |
| 6 | Taking down wooden chowkats or frames with shutters with exceeding 1.50 Sqm but not exceeding 4.00 Sqm each (without taking of shutters from the frames) complete all as specified and as directed. |
| 7 | Taking down wooden chowkats or frames woth shutters with not exceeding 1.50 Sqm each (without taking of shutters from the frames) complete all as specified and as directed. |
| 8 | Taking down wooden shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each complete all as specified and as directed. |
| 9 | Taking down wooden shutters of any description not exceeding 1.00 Sqm each complete all as specified and as directed. |
| 10 | Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for Key, scrubbing down with water etc. complete all as specified and as directed. |
| 11 | Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and as directed. |
| 12 | Dismantling timber scantling 40 Sqcm and over in section, in any position in unframed work and removing materials from site of work complete all as specified and as directed. |
| 13 | Dismantling wrought iron or mild steel work of any description not otherwise provided for and segregating serviceable materials and keeping for reuse at site and removing unserviceable materials from site of work complete all as specified and as directed. |
| 14 | Material and labour for providing cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concreting complete all as specified and as directed. |
| 15 | Material and labour for 75mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base floring and finish the surface fair and even complete all as specified and as directed. |
| 16 | Material and labour for providing 50 mm thick cement concrete (1:2:4) type B1 (using 20 mm graded aggregate) as in pavings/path surfaces, finished fair and even without using extra cement, and spike rolling to surfaces or making impression of expanded metal whilst the concrete is green surface, complete all as specified and as directed. |
| 17 | Material and labour for 75mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection, paving, footpath etc and finished the surface even and smooth without using extra cement laid in panels including joint filled with sealing compound complete all as specified and as directed. |
| 18 | Material and labour for 25mm thick precast cement concrete louvres and jallies (measured solid) (1:2:4) type B0 (using 12.5mm graded stone aggregate) including all mouldings and set in CM (1:4), excluding frame complete all as specified and as directed. |
| 19 | Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) complete all as specified and as directed. |
| 20 | Materials and labour for half brick thick brick work with old size sub class 'B' bricks straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and as directed. |
| 21 | Material & labour for cutting chases for concealed water tubing, cutting not exceeding 10cm girth and make the surface good as per existing with cement morter 1:3 complete all as specified and |
| 22 | Material and labour for well seasoned 2nd class hard wood timber in scantlings, clean sawn, timber framed and fixed complete all as specified and as directed. |
| 23 | Supply and fixing well-seasoned 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed. |
| 24 | Supply and fix 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Sec-tion 8, clause 8.24 (a) complete all as specified and as directed. |
| 25 | Supply and fix 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares (with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Sec-tion 8, clause 8.24 (a) complete all as specified and as directed. |
| 26 | Supply and fixing for 30mm thick factory made flush door shutters solid core construction with block board core and ply wood face panels commercial type on both faces complete all as specified and as directed. |
| 27 | Material and labour for mild steel works as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed. |
| 28 | Supply and fix framed work such as grills, grating, etc, with ends of bars shouldered and/or riveted or forged into spikes ; window framed gurad bars ; barred iron doors, laddrs, framed balasters, walk ways, railings framed work of water and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed. |
| 29 | Supply and fixing steel work in tubular trusses i.e truss bottom, top bend, sides, side supports, holding plates, posts and base plate etc. including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 etc complete all as specified and as directed. |
| 30 | Supply and fixing as in replacement steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, MS 10mm squrare guard bar, Glazing bar dovetailed or welded for receiving glass and including cutting holes in wall for fixing the window with hold fast in PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) and makding good the disturbed surfaces in CM (1:4) and with the existing finishes to match complete all as specified and as directed. |
| 31 | .-Ditto- all as per item No 29.00 above but without glazing bar and -ditto-. |
| 32 | Supply and fixing Anodised powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators etc with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed |
| 33 | Supply and fixing Anodised powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed. |
| 34 | Supply and fixing anodised powder coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified and as directed. |
| 35 | Supply and fixing Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, as per requirement complete all as specified and as directed. |
| 36 | Supply and fixing 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based corrugated / semi corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer instruction complete all as specified and as directed. |
| 37 | Supply and fixing 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as per manufacturer instruction complete all as specified and as directed. |
| 38 | Supply and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface of Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre tocentre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and finish the surface with joint seaing tape and liquid putty complete all as specified and as directed. |
| 39 | Supply and fixing 4mm thick HSPC(High Pressure Steam Cured) board as in false ceiling with powder coated GI/aluminium snap grid/section of size 600mm x 600mm fixed to wall hanging from soffits/trusses using adjustable supporting hanger comprising of 4mm dia MS rod or wire ‘J’ type hook, nuts, bolts, holding down clips with GI/aluminium section of size 36.5mm x 25mm x 1.4mm (main tee) and 23.5mm x 26.4mm x 1.4mm (cross tee) and wall angle of size 25mm x 25mm x 1.4mm including applying two coats of Acrylic washable distemper (oil emulsion) over a coat of primer after preparation of surfaces of ceiling/Prepainted complete all as specified and as directed. |
| 40 | Supply and fixing 5.50 mm thick Sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.50 Sqm in each pane including hacking out old broken glass from metal frame including punching or drilling out old glazing and removing materials from site complete all as specified and as directed. |
| 41 | Supply and fixing 4.00 mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm in each pane including hacking out old broken glass from metal frame including punching or drilling out old glazing and removing materials from site complete all as specified and as directed. |
| 42 | Supply and fixing 4.00 mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm in each pane complete all as specified and as directed. |
| 43 | Supply and fixing 4.00 mm thick frosted glass, ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm in each pane including hacking out old broken glass from metal frame including punching or drilling out old glazing and removing materials from site complete all as specified and as directed. |
| 44 | Supply and fixing 4.00 mm thick frosted glass, ordinary quality and glazing in square not exceeding 0.5 sqm in each pane fixed to aluminium frame window/ventilator complete all as specified and as directed. |
| 45 | Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed. |
| 46 | Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded decorative coloured laminates PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and decorative coloured laminates PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail or bottom rail ; panelling of decorative coloured laminates PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC laminated sheet beeding, and joined together with solvent cement, supplying and fixing in the frame at the site as per specification complete all as specified and as directed. |
| 47 | Supply and fixing as in replacement Factory Made Solid PVC Moulded Door Shutter With Particle Board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, fixing in frame at site as per specification & drawing etc. complete all as specified and as directed. |
| 48 | Supply and fixing brass bright finish continious (piano) hinges of 40mm width of flap when open complete all as specified and as directed. |
| 49 | Supply and fixing as in replacement 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed. |
| 50 | Supply and fixing 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed. |
| 51 | Supply and fixing as in replacement 75mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed. |
| 52 | Supply and fixing 75mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed. |
| 53 | Supply and fixing as in replacement 50mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed. |
| 54 | Supply and fixing 50mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed. |
| 55 | Supply and fixing as in replacement aluminium anodized, barrel tower bolts, 200mm long of extruded section complete all as specified and as directed. |
| 56 | Supply and fixing aluminium anodized, barrel tower bolts, 200mm long of extruded section complete all as specified and as directed. |
| 57 | Supply and fixing as in replacement aluminium anodized, barrel tower bolts, 100mm long of extruded section complete all as specified and as directed. |
| 58 | Supply and fixing aluminium anodized, barrel tower bolts, 100mm long of extruded section complete all as specified and as directed. |
| 59 | Supply and fixing as in replacement 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 60 | Supply and fixing 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 61 | Supply and fixing as in replacement 100mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 62 | Supply and fixing 100mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 63 | Supply and fixing as in replacement 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts,of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 64 | Supply and fixing 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts,of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 65 | Supply and fixing 150mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts,of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 66 | Supply and fixing for 300mm long mild steel ordinary rat tail rod pattern springs for doors including roller and roller plate complete all as specified and as directed. |
| 67 | Supply & fixing Mortice lock,vertical type, size 100 mm, 4 Levers, made of brass complete all as specified and as directed. |
| 68 | Supply and fixing Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass,other parts made of mild steel heavy duty and fixed complete all as specified and as directed. |
| 69 | Supply and fixing 15 to 20 kg capacity soft closing stainless steel tesescopic sliding drawer channel suitable for modular kitchen cabinet, drawer/racks complete all as specified and as directed. |
| 70 | Supply and fixing as in replacement stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed. |
| 71 | Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed. |
| 72 | Supply and fixing as in replacement 19/20mm dia mild steel chromium plated curtain rods with and including fixing socket and Bracket complete all as specified and as directed. |
| 73 | Supply and fixing 18/19mm thick MDF board, commercial type fixed with screws to timber frame work as in linings, panelling similar location cup board shutter, shelf, kitchen cabinets etc. complete all as specified and as directed. |
| 74 | Material and labour for non skid ceramic coloured tiles (Premium Quality) 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm coloured in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. |
| 75 | Material and labour for Vitrified ceramic coloured tiles (light shade) 10mm thick (Square/rectangular) area of each tile not exceeding 0.36 sqm coloured in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. |
| 76 | .-Ditto- all as per item No 74.00 above but in skirting and dado laid over and including 10mm thick rendering in cement mortar (1:4) and -ditto-. |
| 77 | Material and labour for glazed ceramic coloured tiles (Premium Quality) of size 300x200x7mm thick as on vertical surfaces, set and jointed in neat cement slurry and pointed in white cement with pigment to match with the shade of tiles laid over and including 10mm thick cement plaster in CM (1:4) complete all as specified and as directed. |
| 78 | Material and labour for precast Cement Concrete chequered tiles of size 200 x 200 x 25mm thick as in floor, set and jointed in neat cement slurry and pointed with cement laid over and including 20mm thick screed bed in CM (1:4) complete all as specified and as directed. |
| 79 | Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 80 | Material and labour for Granite work (of any type) 20 mm thick (table rubbed and polished) in slab, jambs, platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade complete all as specified and as directed. |
| 81 | Materials and labour for 15 mm thick rendering on brick work in cement mortar (1:6) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 82 | Materials and labour for 15 mm thick rendering on fair faces of brick work or concrete surface in cement mortar (1:4) with using water proofing coumpound and as per manufacturer specification and finished the surfaces even and smooth without using extra cement complete all as specified and as directed.Note : WPC will be measured and paid separately. |
| 83 | Materials and labour for 5 mm thick rendering on concrete surfaces in ceiling in cement mortar (1:3) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 84 | Supply only liquid integral water proofing compound conforming to IS-2645 complete all as specified and directed. |
| 85 | Materials and labour for preparation of old plastered surfaces of walls after complete removal of existing treatment and applying two coats of cement base paint complete all as specified and as directed. |
| 86 | Material and labour for preparation of old plastered surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of cement base paint on walls complete all as specified and as directed. |
| 87 | Materials and labour for preparation of old plastered surfaces of wall and Finishing the surface with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @2.20kg/10 sqm applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth after complete removal of existing treatment on walls complete all as specified and as directed. |
| 88 | Materials and labour for preparation of old plastered surfaces of walls after complete removal of existing treatment and applying Acrylic Smooth exterior paint (Weather Coat) 1st quality of required shade (Two coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and as directed. |
| 89 | Materials and labour for preparation of newly plastered surfaces of wall Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)complete all as specified and as directed. |
| 90 | Materials and labour for preparation of newly plastered surfaces of wall and applying two coats of acrylic washable distemper over a coat of primer over and including 1mm thick wall care putty complete all as specified and as directed. |
| 91 | Materials and labour for preparation of newly plastered surfaces of ceiling and applying two coats of acrylic washable distemper over a coat of primer over and including 1mm thick wall care putty complete all as specified and as directed. |
| 92 | Materials and labour for preparation of old plastered surfaces of walls and applying two coat of acrylic washable distemper after and including washing and rubbing down existing treatment with water complete all as specified and as directed. |
| 93 | Materials and labour for preparation of old plastered surfaces of ceiling and applying two coat of acrylic washable distemper after and including washing and rubbing down existing treatment with water complete all as specified and as directed. |
| 94 | French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler (if required) on old wooden surface with two coats of french polish complete all as specified and as directed. |
| 95 | Material and labour for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 96 | Material and labour for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 97 | Material and labour for preparation of new wooden surfaces of any description not exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 98 | Material and labour for preparation of old steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamal paint complete all as specified and as directed. |
| 99 | Material and labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamal paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 100 | Taking up or down steel tubing 20 mm bore and connections including cleaning for refixing or removal to store complete all as specified and directed. |
| 101 | Taking up or down steel tubing 15 mm bore and connections including cleaning for refixing or removal to store complete all as specified and directed. |
| 102 | Supply and fix 20mm bore galvanised steel water tubing medium grade including all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as direcetd. |
| 103 | Supply and fix 15mm bore galvanised steel water tubing medium grade including all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as direcetd. |
| 104 | Supply and fixing as in replacement 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with suitable size of MS flat iron clamp complete all as specified and as directed. |
| 105 | Supply and fixing as in replacement 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with suitable size of MS flat iron clamp complete all as specified and as directed. |
| 106 | Supply and fixing 110 mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 107 | Supply and fixing 75 mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 108 | Supply and fixing 110 mm bore, PVC (SWR) branch pieces, single (single ‘Y’) equal or unequal complete all as specified and as directed. |
| 109 | Supply and fixing 75 mm bore, PVC (SWR) branch pieces, single (single ‘Y’) equal or unequal complete all as specified and as directed. |
| 110 | Supply and fixing 110mm bore PVC (SWR) junction single, (Single T) equal or unequal, with oval access door complete all as specified and as directed. |
| 111 | Supply and fixing 75mm bore PVC (SWR) junction single, (Single T) equal or unequal, with oval access door complete all as specified and as directed. |
| 112 | Supply and fixing 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 113 | Supply and fixing 75mm dia, PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 114 | Supply and fixing 125/110 mm dia, PVC (SWR) gully trap, including jointing with solvent cement complete all as specified and as directed. |
| 115 | Supply, hoisting and fixing in proper position ISI marked multi-layer rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), of capacity 1000 litres with and including 20mm bore PTMT float and ball valve set including providing necessary connections after demolition existing PVC tank complete all as specified and as directed. |
| 116 | Supply, hoisting and fixing in proper position ISI marked multi-layer rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), of capacity 500 litres with and including 20mm bore PTMT float and ball valve set including providing necessary connections after demolition existing PVC tank complete all as specified and as directed. |
| 117 | Supply and fixing as in replacement Vitreous China squatting pan of ‘Orissa pattern’, size 580 mm x 440mm (white) with ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern complete including provision of PCC bedding and connection to trap, flushing pipe, antisyphonage pipe, etc. including making good the disturbed floor complete all as specified and as directed. |
| 118 | Supply and fixing as in replacement vitreous China white wash down water closet pan (pedestal pattern) with ‘P’ or ‘S’ trap, front or back inlet, fixing bolts, with white PVC seat cover, jet spray and providing 32 mm dia PVC flush pipe and making all necessary connections complete as specified and as directed. |
| 119 | Supply and fixing as in replacement floor mounted vitreous China white wash down water closet pan bowel shape (pedestal pattern and casement style) with ‘P’ or ‘S’ trap, front or back inlet, fixing bolts, with soft close slim white PVC seat cover, inbuilt dual type flushung cistern and making all necessary connections complete as specified and as directed. |
| 120 | Supply and fixing as in replacement vitreoues china WHB, white, flat back, of size 550X400mm including CP brackets, CP waste coupling 32 mm bore, PVC waste pipe 32mm dia with and including 15mm bore PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and as directed. |
| 121 | Supply and fixing as in replacement looking mirror of size 600mm x 450mm x 5mm thick bevelled edge of selected quality glass, decorative type mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. |
| 122 | Supply and fixing as in replacement 10 litre capacity low level PVC flushing cistern (White colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed. |
| 123 | Supply and fixing as in replacement premium quality Brass Cromium Plated Wall Mixer 3-in-1 System with Provision for both Hand Shower and Overhead Shower complete with L shape long Bend pipe, connecting Legs & Wall Flange (without Overhead Shower) including hand shower and suitable size of flexible tube complete all as specified and as directed. |
| 124 | Supply and fixing as in replacement premium quality Brass Cromium Plated Central Hole Basin Mixer with regular Spout without Popup waste system with 450mm long Braided Hoses complete all as specified and as directed. |
| 125 | Supply and fixing as in replacement 15mm bore fancy type bib taps cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed to pipe complete all as specified and as directed. |
| 126 | Supply and fixing as in replacement 15mm bore fancy type 2 way bib taps cast copper alloy chromium plated twin -leaver operated, with built in areator and wall flange screwed to pipe complete all as specified and as directed. |
| 127 | Supply and fixing as in replacement for 15mm bore stop valve, brass fancy type chromium plated, screwed down high pressure with crutch or butter fly handle screwed both ends fixed to GI pipe complete all as specified and as directed. |
| 128 | Supply and fixing as in replacement for 15mm bore stop valve, brass fancy type chromium plated with long shank and cup (Concealed Type), screwed down high pressure with crutch or butter fly handle screwed both ends fixed to GI pipe complete all as specified and as directed. |
| 129 | Supply and fixing as in replacement 15mm bore Chromium Plated pillar tap fancy type cast copper alloy, with capstan heads screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for pipe complete all as specified and as directed. |
| 130 | Supply and fixing as in replacement 125mm dia chromium plated shower rose with revolving joints fixed to 240mm long chromium plated shower arm (Light weight) round shape with wall flange complete all as specified and as directed. |
| 131 | Supply and fixing as in replacement hand shower (health faucet) (ABS Chrome palted) with 8mm dia, 1m long, flexible tube with wall hook complete all as specified and as directed. |
| 132 | Supply and fixing as in replacement soap dish holder brass chromium plated of approximate size 200x 200x90mm fixed to plugs with chromium plated brass screws complete all as specified and as directed. |
| 133 | Supply and fixing as in replacement toilet paper holder brass chromium plated with stainless steel flap cover including necessary accessories complete all as specified and as directed. |
| 134 | Supply and fixing as in replacement 32mm dia CP waste coupling including CP waste pipe complete all as specified and as directed. |
| 135 | Supply and fixing as in replacement tubular towel rail brass chromium plated, 20mm dia, D type, 60cm long fixed with two plugs (gutties) of 2nd class hard wood embedded in CM 1:3 with screws complete all as specified and as directed. |
| 136 | Supply and fixing as in replacement 20mm bore Gun metal Globe or gate valve with iron wheel head and gun metal spindle screwed both ends complete all as specified and as directed. |
| 137 | Supply and fixing as in replacement 15mm bore Gun metal Globe or gate valve with iron wheel head and gun metal spindle screwed both ends complete all as specified and as directed. |
| 138 | Supply and fixing as in replacement Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed. |
| 139 | Supply and fixing as in replacement 20mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight 210 gms) complete all as specified and as directed. |
| 140 | Supply and fixing as in replacement 15mm dia Bib tap fancy type of PTMT any colour high pressure screwed foriron pipe (Minimum weight 105gms) complete all as specified and as directed. |
| 141 | Supply and fixing as in replacement 15mm dia Stop valve of PTMT any colour high pressure screwed for iron pipe(Minimum weight 90gms) complete all as specified and as directed. |
| 142 | Supply and fixing as in replacement 15mm dia Pillar taps of PTMT, fancy type any colour high pressure screwed for iron pipe (Minimum weight 120gms) complete all as specified and as directed. |
| 143 | Supply and fixing as in replacement 15mm dia PVC connection pipe 450mm long with PTMT nuts complete all as specified and as directed. |
| 144 | Supply and fixing as in replacement stainless steel (conforming to AISI-304 grade) kitchen sink with drain board of overall size 915mm x 460mm and bowl size 410mm x 352mmx 178mm depth or equivalent made of 1mm thick stainless steel sheet with 32mm bore CP waste coupling, 32mm bore PVC waste pipe(heavy duty) 90 cm long, 15mm dia 450mm long PTMT connection pipe and bedded in cement mortar and fixed on CP cantilever brackets, complete all as specified and as directed. |
| 145 | Supply and fixing as in replacement stainless steel (conforming to AISI-304 grade) plate rack of overall size 610mm x 610mm x 254mm or equivalent made of 0.60mm thick stainless steel sheet fixed on CP cantilever brackets, complete all as specified and as directed |
| 146 | Supply and fixing as in replacement stainless steel (conforming to AISI-304 grade) plate rack of overall size 610mm x 914mm x 254mm or equivalent made of 0.60mm thick stainless steel sheet fixed on CP cantilever brackets, complete all as specified and as directed Please Enable Macros to View BoQ information |
