|
| 1 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specified provided for complete all as specified and as directed. |
| 2 | Demolition of cement concrete (incl floor tiles, kota stone flooring etc) (unreinforced) of any description in ground floors and pavings not exceeding 15cm thickness below or above ground level complete all as specified and as directed. |
| 3 | Taking down of cement plaster from brick walls hacking for keys & scrubbing down with water including raking of joints etc as in patches complete all as specified and as directed. |
| 4 | Material and labour for taking down / dismantling of existing roof treatment of any description such as old APP membrane roof treatment etc terracing including screed bed etc., Hessian base felt/tar felt etc. (any type and thickness) including removing the same from site complete all as specified & directed. |
| 5 | Material and labour for cement concrete 25mm (minimum thickness) levelling course, type B-0, 1:2:4 (12.5mm graded stone aggregate) as in roof padding including filling of depressions & maintaining required slope including coved fillets, finished the surfaces even and smooth without using extra cement, complete all as specified and directed. |
| 6 | Material and labour for 10mm thick screed bed in cement mortar 1:4 on concrete surfaces, finished even and smooth including mixing water proofing compound as per manufacturer's instructions complete all as specified and directed.Note :- WPC to be measured and separately as supply only under appropriate item in this BOQ.) |
| 7 | Material and labour for roof surface treated with PU Elastoseal primer to seal the pores and enhance the adhesion of the coating, supplying and applying single component waterproofing liquid membrane based on pure, elastometric, polythene resin cold applied of spray/brush applied membrane with an elongation of 650%+50 and tensile strength not less than 2 Mpa crack bridging ability not less than 2mm. No leakage upto 5 bars of water pressure. Shore Hardness >50 Shore. The minimum thickness to be applied shall be 1.5mm (overall) in two layers (each layer 750 micron) or as per manufacturer's instructions so as to achieve thickness not less than 1.5mm including providing & laying of protective Geotextile fabric 150 GSM over than entire membrane with proper overlaps of 75mm complete all speciifed. The finished roof colour will be in dark brown, grass green, olive green or as directed by Engr-in-charge. Note: (i) The treatment shall be carried out by authorised applicator approved by GE as per the manufacturer. (ii) Payment will be made after providing warranty for 10 years certified from the company. |
| 8 | Supply only liquid water proofing compound complete all as specified and directed. |
| 9 | Material and labour for 15mm thick rendering in cement mortar 1:4 on fair face of brick work or concrete surfaces or on stone surfaces finished even & smooth without using extra cement including mixing water proofing compound @200ml/50Kg of cemen.complete all as specified and directed. Note: WPC to be measured and separately as supply only under appropriate item in this BOQ.) |
| 10 | Material and labour for 10mm thick rendering in cement mortar 1:6 on stone masonry or other than fair face of brick work, surface finished even & smooth without using extra cement complete all as specified and directed. |
| 11 | Material and labour for GI wire chicken mesh of size 25mm X 25mm to concrete of joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specified and directed. |
| 12 | Material and labour for 5mm thick rendering on ceiling surfaces in cement mortar 1:3, finished fair and even without using extra cement complete all as specified and directed. |
| 13 | Material and labour for preparation of new plastered or unplastered surface of any description and finishing with Acrylic Smooth exterior paint of required shade (Two or more coats), applied @ 1.67 ltr/10sqm over and including priming coat of exterior primer applied @ 2.20 kg/10sqm complete all as specified and directed. |
| 14 | Material and labour for preparation of old plastered or unplastered surface of any description and finishing with Acrylic Smooth exterior paint of required shade (Two or more coats), applied @ 1.67 ltr/10sqm over and including priming coat of exterior primer applied @ 2.20 kg/10sqm complete all as specified and directed. |
| 15 | Material and labour for preparation of new plastered surfaces of any description and applying two coats of distemper oil emulsion (OBD) over a coat of primer on wall surface of any description over and including 1 to 2mm thick wall care putty in two or more layers as per site requirement complete all as specified and directed. |
| 16 | Material and labour for preparation of old plastered surfaces of any description and applying one coat of distemper oil emulsion (OBD) complete all as specified and directed. |
| 17 | Material and labour for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 18 | Material and labour for preparation of old whitewash surfaces of ceiling and applying two coats of white wash on ceiling complete all as specified and directed. |
| 19 | Material and labour for 25mm thick PCC 1:2:4, type B-0 using 12.5mm graded aggregate as in sub base of floor finished the surfaces even & smooth without using extra cement complete all as specified and directed. |
| 20 | Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 21 | Material and labour for Machine cut prepolished kota stone single piece for tread and riser flooring/skirting 18-20mm thick over 15mm thick screed in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 22 | Material and labour for Machine cut pre polished kota stone slab flooring18-20mm thick over 15mm thick screed in CM (1:6) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed. |
| 23 | Material and labour for Non-skid ceramic tiles 10 to 12 mm thick light shade of size 1200mm x 600mm polished as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 24 | Material and labour for Non-skid ceramic tiles 10 to 12 mm thick light shade of size 1200mm x 600mm polished as in skirting, including 10mm thick back coat in CM 1:4 complete all as specified and directed. |
| 25 | Supply and fixing in repair 0.56mm thick plain aluminium sheeting, alloy 31000H4 in ridges, hips, velly gutter, drip and straight flashing (length and girth as fixed) complete all as specified and directed. |
| 26 | Taking down steel window shutters of any description not exceeding 1 sqm each and refixing the same at the existing opening after repairing steel hinges, bolts, handles etc complete all as specified and directed. |
| 27 | Taking down shutter of any description exceeding 1 sqm but not exceeding 2 sqm each and refixing the same opening after resecuring or easing & adjusting complete all as specified and directed. |
| 28 | Taking down shutter of any description exceeding 1 sqm but not exceeding 2 sqm each and removing to store complete all as specified and directed. |
| 29 | Supply and fixing factory made, 2nd class hardwood, 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass / gauge etc. (without sash bars) edges or framing plain, chamfered or rounded fitted with cut or mitered beads for securing glass etc. size of members of shutters as specified in SSR Part - I section 8.20 (a), complete all as specified and directed. |
| 30 | Supply and fixing factory made 35mm thick 2nd class hardwood, plain framed, paneled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, 35mm thick complete all as specified and directed. |
| 31 | Supply and fixing Aluminium, anodised, handles 150mm of extruded section and fixed complete all as specified and directed. |
| 32 | Supply and fixing Aluminium, anodised, barrel tower bolt if extruded section 150mm long complete fixed with steel screws complete all as specified and directed. |
| 33 | Supply and fixing Aluminium alloy, anodised, sliding door bolt 250mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed. |
| 34 | Supply and fixing 100mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed. |
| 35 | Material and labour for preparing of new or previously untreated surfaces of wood of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 36 | Material and labour for preparing of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 37 | Material and labour for preparing of old steel or iron surfaces of any description not exceeding 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 38 | Supply and fixing GI wire cloth 0.56mm nominal dia of wire and 1.18mm average width of aperture complete with beads etc. for door shutter/window shutter of any size/type/thickness complete all as specified and directed. |
| 39 | Supply and fixing in repair GI wire cloth 0.56mm nominal dia of wire and 1.18mm average width of aperture complete with beads etc. for door shutter/window shutter of any size/type/thickness complete all as specified and directed. |
| 40 | Supply and fixing in repair sheet glass pane ordinary quality & glazing with oil putty 3mm thick not exceeding 0.50sqm complete all as specified and directed. |
| 41 | Supply and fixing rotational molulded polyethylene water storage tanks ( Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I, of capacity 2000 Ltrs including dismantling existing water of any type, size and capacity complete all as specified and directed. |
| 42 | Disconnecting existing tanks, setting aside (or lowering if required ) for repairs, cleaning, etc. and hoisting if required reconnecting and refixing in position of capacity 2000Ltrs including cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. complete all as specified and directed. |
| 43 | Taking up or down 25mm bore steel tubing & connection and refixing the same at the existing position after cleaning complete all as specified and directed. |
| 44 | Supply and fixing in repair GI tubing medium grade 25mm dia with all fittings, cutting, threading and fixing to walls, ceiling or in floors complete all as specified and directed. |
| 45 | Taking up or down 20mm bore steel tubing and connection and refixing the same at the existing position after cleaning complete all as specified and directed. |
| 46 | Supply and fixing in repair GI tubing medium grade 20mm dia with all fittings, cutting, threading and fixing to walls, ceiling or in floors complete all as specified and directed. |
| 47 | Supply and fixing in repair 20mm dia Gun-metal, lever type gate valves, with lever type, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 48 | Supply and fixing in repair 25mm dia Gun-metal, lever type gate valves, with lever type, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 49 | Supply and fixing in repair 20mm bore, Ball brass valves, high pressure, with polythene float and fly nuts complete, screwed for iron pipe or brass ferrule complete all as specified and directed. |
| 50 | Supply and fixing of tank nipple suitable for HDPE water tank of 15mm/20mm and 150mm long with washer complete all as specified and directed. |
| 51 | Material and labour for 50mm thick in plain cement concrete type C1 (1:3:6) using 20mm graded aggregate as in plinth protection laid in alternate bays (not exceeding 2 Sqm each ) finished even and smooth at top without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed. |
| 52 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 53 | Material and labour for RCC 1:2:4, type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams, columns, floor, rocks, balconies, landing, canopies, deck, slabs, shelves, chajja and the like including necessary formwork complete all as specified and directed. |
| 54 | Material and labour for mild steel TMT bars 10mm dia and above, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 55 | Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs not exceeding 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 5cm but not exceeding 10cm wide finished fair surface complete all as specified and directed. |
| 56 | Demolition of Brickwork of stone/ boulder masonry, build in cement mortar incl all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 57 | Taking down chowkhats or frames with shutters without taking off shutters from frames area not exceeding 1.50 sqm each complete all as specified and directed. |
| 58 | Material and labour for 18-20mm thick Granite (of any type ) work (table rubbed and polished) in steps , jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including moulding of corners as required including taking down existing plaster complete all as specified and directed. |
| 59 | Dismantling wrought iron or mild steel work of any description not otherwise provide for complete all as specified and directed. |
| 60 | Material and labour for mild steel work as in staging for water tanks and the like including caps, bases, splices, etc built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc conforming to FE 410-W (Gde-E-250) quality-A complete all as specified and directed. |
| 61 | Material and labour for preparation of new steel or iron surfaces of any description not exceeding 10cm width or girth and applying two coats of synthetic enamel paint over red oxide zinc chrome primer complete all as specified and directed. |
| 62 | Material and labour for PCC 1:2:4, type B1 using 20mm graded stone aggregate as in coping, benching of manhole etc complete all as specified and directed. |
| 63 | Material and labour for walling of random rubble uncoursed stone masonry, well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed. |
| 64 | All as per item No 63 above but except stone |
| 65 | Material and labour for hammer dressing to face stones with maximum depressions of 40mm from straight edge held against the surface, beds, joints complete all as specified and directed. |
| 66 | Material and labour for raised pointing to RR masonry in cement mortar 1:4 complete all as specified and directed. |
| 67 | Material and labour for providing precast cement concrete 1:3:6 type C1 using 20mm graded stone aggregate as in PCC bonders set in CM 1:6 complete all as specified and directed. |
| 68 | Material and labour for 110mm bore PVC pipes as in weep holes complete all as specified and directed. |
| 69 | Material and labour for broken stone or boulders including hand packing (any thickness) at back side of weep holes and raising or lowering to the required level complete all as specified and directed. |
| 70 | Material and labour for 100mm thick PCC 1:5:10 type E-2 using 40mm graded stone aggregate as in sub base of floor, etc complete all as specified and directed. |
| 71 | Material and labour for chequered colour cement concrete tiles with grey cement and pigment of size 30cmx30cm x25mm thick set jointed and pointed in neat cement slurry in floors/steps including 20mm thick screed bed in cement mortar 1:4 complete all as specified and directed. |
| 72 | Material and labour for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm ), including making drainage opening wherever required complete all as specified and directed. |
| 73 | Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation and getting out in hard/dense soil complete all as specified and directed. |
| 74 | Demolition and breaking up drain pipes any size (SGSW, AC, PVC or reinforced concrete) set in cement mortar/concrete complete all as specified and directed. |
| 75 | Material and labour for brickwork with subclass 'B' old size bricks, straight or curve on plan exceeding 6m mean radius in cement mortar 1:4 complete all as specified and directed. |
| 76 | Material and labour for providing RCC 1:2:4, type B1 using 20mm graded stone aggregate as in precast cover slabs for manholes and drains including necessary use of formwork and set in cement mortar 1:4 complete all as specified and directed. |
| 77 | Supply and laying of NP 2 pipes 150mm bore, laid and jointed complete with collar per length of pipe complete all as specified and directed. |
| 78 | Material and labour for PCC 1:3:6, type C2 (20mm graded aggregate) as in concrete bed to drain pipes of 150mm bore incl packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 79 | Extra for forming fair finished drain or drain channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/ stopped ends etc complete all as specified and directed. |
| 80 | Returning, filling in soft/loose soil incl, spreading, levelling, watering and well ramming in layers not exceeding 25cm complete all as specified and directed. |
| 81 | Removing of surplus material exceeding 250m but not exceeding 500m and deposited where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed. |
| 82 | Material and labour for construction of Soakage wells of size 3.00 mtr depth, excavation in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of brick masonry in cement mortar, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats, including demolition of existing sokage wells complete all as specified and directed. |
| 83 | Material and labour for precast factory made drain cover of size width 1000mm length 550 to 600mm and 70 to 80 mm thickness of grade M30 with holes / cutting slotted for drain out the rain water as per IS 12592 complete all as specified and directed. |
| 84 | Material and labour for PCC 1:3:6, type C1 (using 20mm graded aggregate) as in surface channels and drains complete all as specified and directed. |
| 85 | Taking down carefully aluminium/ copper point wiring (light, fan, socket or power) complete incl fittings & fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings, etc. and making good disturbed surfaces of wall, floors etc complete all as required and keeping serviceable light fittings in safe custody for reuse in the work as directed. |
| 86 | Material and labour for wiring on wall/surface in PVC casing caping of size 20mm complete with 1.5 Sqm single core multistranded copper conductor FRLS PVC insulated and unsheathed cable 1100 volts grade drawn through including PVC casing caping and provisining of 1.5 sqm FRLS PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor to common earth and connected to earth dolly with sunken type pressed steel /welded MS terminal boxes made out of 1.6mm MS sheet, 3mm thick laminated sheet top cover for mounting of fittings, switches, sockets, outlets, regulators etc complete one light/ fan point controlled by one switch 5 amp one way complete all as specified and directed. |
| 87 | All as per item No. 87 but One 3 pin 5 Amps socket point controlled by one switch on same board. |
| 88 | All as per item No. 87 but One 3 pin 5 Amps socket point controlled by one switch on independent board. |
| 89 | All as per item No. 87 but One light point controlled by one 2 way switch. |
| 90 | All as per item No. 87 but point wiring with 2.5 sqmm single core multi stranded copper conductor FRLS PVC insulated and unsheathed cable 1100 volts grade and 2.5 sqmm FRLS PVC insulated and unsheathed cable 1100 volts grade with multi stranded copper conductor for earth wire for 15/16 amp multipurpose socket combination point on independent board. |
| 91 | Material and labour for submain wiring with 2 runs of copper conductor FRLS PVC insulated and unsheathed cable 1100 volts grade 4 sqmm drawn through PVC casing caping 25mm dia ISI marked as per IS specification fixed on wall / ceiling including conduit and conduit accessories and including provision of PVC insulated 4 sqmm FRLS multistranded copper conductor as earth continuity conductor connected to earth dolly all as specified including dismantling old submain wiring and making good to the disturbed surface by plastering and two coat of distemper complete all as specified and directed. Note: Two runs of 4 sqmm cable alongwith one run of 4 sqmm PVC insulated unsheathed copper conductor as earth wire, conduit and conduit accessories will be measured as one length complete all as specified and directed. |
| 92 | Supply and fixing switch piano flush type single pole, one way 6 amp complete all as specified and directed. |
| 93 | Supply and fixing switch piano flush type single pole, 2 way 6 amp complete all as specified and directed. |
| 94 | Supply and fixing socket outlet 2 in 1, 3 pin 5 A flush type complete all as specified and directed. |
| 95 | Supply and fixing switch piano flush type single pole, 1 way 15 amp complete all as specified and directed. |
| 96 | Supply and fixing socket outlet 2 in 1, 3 pin 15 A flush type complete all as specified and directed. |
| 97 | Supply and fixing ceiling rose 65x50mm three terminals 230 volt complete all as specified and directed. |
| 98 | Supply and fixing step type fan regulator electronic type in 5 step, 100 watt capacity switch/socket type complete all as specified and directed. |
| 99 | Supply and fixing lamp holder, PVC/Polycarbonate type and back plate suitable for batten fitting complete all as specified and directed. |
| 100 | Supply and fixing inverter LED lamp, CDL 9 watt, B22 base, complete all as specified and directed. |
| 101 | Supply and fixing inverter LED batten 1x 20 W, with square profile and polycarbonate channel, lithium iron battery with charging time of 8 to 10 hours and backup tile upto 04 hours with driver, holder incl LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 102 | Supply and fixing distribution board double door type (for incoming MCCB & outgoing MCBs) TPN 4 way vertical type sheet steel powder painted with bus bar , neutral link & earth bar etc. with IP 43 degree of protection flushing in wall including connecting up all incoming and outgoing cables/circuit wiring complete all as specified and directed. |
| 103 | Supply and fixing sheet metal enclousures for MCB distribution board 230 Volts single pole and neutral 12 way double door type flushed inside the wall with 200 Amp rated bus bar including making the surface good complete all as specified and directed. |
| 104 | Supply and fixing sheet metal enclousures for MCB distribution board 230 Volts single pole and neutral 4 way double door type flushed inside the wall with 200 Amp rated bus bar including making the surface good complete all as specified and directed. |
| 105 | Supply and fixing MCCB 100 Amp, 4 pole 16 KA with adjustable thermal release fixed magnetic protection complete all as specified and directed. |
| 106 | Supply and fixing MCB SPN, 63 Amp, B curve 240 Volts 10 KA finger proof terminal, bi-connect termination, label holder, 35 mm2 terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB complete all as specified and directed. |
| 107 | Supply and fixing MCB SPN, 40 Amp, B curve 240 Volts 10 KA finger proof terminal, bi-connect termination, label holder, 35 mm2 terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB complete all as specified and directed. |
| 108 | Supply and fixing MCB SPN, 5 to 32 Amp B curve 240 Volts 10 KA finger proof terminal, bi-connect termination, label holder, 35 mm2 terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB complete all as specified and directed. |
| 109 | Supply and fixing ceiling fans complete with three blade, down rod, accessories 230V , 1200mm sweep, BLDC fan with 5 star rating complete all as specified and directed. |
| 110 | Supply and fixing electric water heater, storage type steel body with copper inner tank and heating element upto 1.5 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as saftey valve, thermostate, NRV, connection piece etc. complete all as specified and directed. |
| 111 | Supply and fixing energy efficient LED light fitting, 35W, input voltage 110V to 280VAC, 50Hz with ingress protection IP 66, LM 80, stranded luminries with efficiency 100lumen/Watt, with secondry optics, perfectly matched lenses, complying to IEC60598/IS10322, with auto shutdown on high voltage, CRI>70, PF>0.95, with short circuit & reverse circuit protection against 10KV high surges, minimum 25000 burning hours (life), operating temperature 1 to 50C, rectangular shape with pressure die cast aluminium housing with weather proof gasket for lamp and driver compartment with system wattage of 35W=10%W, rated lumens, 120o view angle,constant current type driver having THD<10%, incl all fixing arrangement like clamps, nuts, bolts, washers, 35W LED rod lamp (having PF>0.9, input voltage 90-300V, IP-66, LM80) with all accessories pre-wired and connecting with twin core twisted flexible copper conductor cable with all necessary staging, etc. incl bracket complete all as specified and directed. |
| 112 | Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 sqmm 4 core complete all as specified and directed. |
| 113 | Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation and getting out in soft/loose soil complete all as specified and directed. |
| 114 | Removing of surplus material not exceeding 50m and deposited where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed. |
| 115 | Material and labour for river sand as in sand cushioning to under ground cable 8 cms thick before laying the cable and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and directed. Note : For payment purpose punned thickness 18cm shall be measured. |
| 116 | Material and labour for brick protection cover of UG cable by old size bricks common burnt clay building bricks sub class 'B' laid dry and flat abutting each other with width equal to length of brick and gap between adjacent brick not exceeeding 10mm complete all as specified. |
| 117 | Supply and fixing bus bar chamber of size 600x600x450mm suitable of 3 phases 433V outdoor type fabricated outbof 3.15mm thick MS sheet with 300A rated aluminium bus bar 4Nos., PVC sleeves (coloured red, yellow, blue and black) with suitable locking arrangments and four legged angle iron stand made of angle iron of size 40x40x6mm duly grouted in and including foundation in PCC 1:2:4 type C1 using 20mm graded stone aggts alongwith all necessary cable connections, lugs and cable glands including applying two coats of synthetic enamel paint (of approved tint) over a coat of red oxide zinc chrome primer complete all as specified and directed. |
| 118 | Material and labour for earthing complete vwith galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level , the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and including connected to and including galvanized earth lead strip 25x4 mm size upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of GI and connected to earthing test point and earth dolly all as shown in electrical plate No 3 of MES SSR part 1 and testing on completion including necessary excavation and earth work in any type of soil , PCC (1:3:6) TYPE C1 chamber, precast RCC slab 50mm thick in cement concrete (1:2:4), type B1, reinforced with welded steel wire fabric or XPM, (weight not less than 4 Kg per Sqm) with cast iron frame , funnel with watering pipe 20mm dia medium grade, wire mesh and lugs, GI protection pipe , 40mm dia, light grade, 7.5 mtr long for protection of earth lead upto test point etc complete all as specified and directed. |
| 119 | Material and labour for earthing complete with galvanized steel earth plate electrode 600x600x3.15mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level , the earth electrode surrounded by adequate quantityof charcoal dust and salt to a packed thickness of 15cm on all side and incl connected to and including GI wire as earth lead 4.0 mm size upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of brass and connected to earthing test point and earth dolly all as shown in electrical plate No 3 of MES SSR part 1 and testing on completion including necessary excavation and earth work in any type of soil , PCC (1:3:6) TYPE C1 chamber, pre-cast RCC slab 50mm thick in cement concrete (1:2:4), type B1, reinforced with welded steel wire fabric or XPM, (weight not less than 4 Kg per Sqm) with cast iron frame ,funnel with watering pipe 20mm dia medium grade, wire mesh and lugs, GI protection pipe , 15mm dia, light grade, 7.5 mtr long for protection of earth lead upto test point etc complete all as specified and directed. |
| 120 | Deduction to be made from BOQ for Sch 'A' Part -II i.e. (Schedule of credit) amount during AOC.Note: Tenderers shall not quote for this schedule. Please Enable Macros to View BoQ information |
