Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Taking down of existing roof treatment inclding all loose and de-bonded concrete / screed, loose particles, dirt etc & debris should be removed from bldg. Roof substrate must be pressure - washed with water with a minimum working pressure of 1400 psi is to be used to and / or remove all dirt, dust, chalking and wast products. Remove algae, mold by using bleach solution or biowash etc complete all as specified and direccted by Engr in charge. |
| 2 | M&L for apply one coat of primer after dilution of water proofing chemicals in the ratio 1:1 in complete dry condition where moisture contain below 7% (Moisture should be checked with moisture meter). Allow the primer coat to dry for 6 to 8 hours. Apply 1st coat of roof seal classic or equivalent water proofing chemical without dilution spreading at the rate of 0.70 / litre / sq mt/ coat until all surface is covered. lay a 45 GSM fibre glass mesh as a reinforcing material which is incorporated in the coating when the first coat is still in wet condition. Allow the first coat to dry for approximately 4 to 6 hours. Apply the second of chemical with the same application coverage, but in a direction perpendicular to that of the first and second coats. Allow each coat to air cure for a minimum of 4-6 hours after application. Check to see no avoid surface is left untreated / uncoated. Allow the system to air cure for 7 days minium etc complete all as specified and directed and as per manufacturer instructions. |
| 3 | M&L for repair of All visible hairline cracks on concrete roof / screed more than 0.50 mm and not giving hollow sound, should be cut and widen in V shape with mechanical cutter in the size (10mm W x 6mm D). Fill cracks with PU sealed / Hybrid sealant with suitable gun and smoothed with a putty knife or towel. Allow sealant to cure a minimum (72 Hrs) 3 days etc complete all as specified & directed. |
| 4 | M&L for apply a bond coat of pidicrete URP or equivalent mix in the ratio of 1:1 (URP 1:cement 1 ) by volume to make it lump free slurry when applied on in the pre wet surface. Laid to fall roof screed in correct slope and gradient mix pidicrete URP 10% by weight of cement in concrete in ratio of 1:1.5:3 i.e. one bag of 50 kg cements : 1.5 times volume of sand : 3 times volume of aggregates (12.5 mm aggregate) & average thickness of concrete should be 25 mm and finish with trowel. surface should be smooth and even. Before application of water proofing chemical the roof surface should be cured enough etc complete all as specified and directed. |
| 5 | Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 6 | S&F 5.0 cm thick sand stone slabs in sun shades, chajjas, shelves, roof slabs etc n.exc. 2m in length punched dressed on face and along exposed edges, self faced on other side and set and pointed in CM 1:4 complete all as specified and directed. |
| 7 | M&L for Cement concrete 1:2:4 type B-1 ( using 20mm graded crushed stone aggregate) as in benching,coping , roof kerbs, mud stop, padding etc and similar work all as specified and directed. |
| 8 | Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and pre-cast concrete articles complete all as specified and directed. |
| 9 | M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified & directed |
| 10 | Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified & directed |
| 11 | Taking down cement or cement lime plaster of any discription on brick or stone walls/ ceilings etc, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 12 | M &L for 10 to 12mm smart care ready mix repair plaster is a specially designed ready to use cement based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering (as per manufacture instructions) over exterior wall ( including necessary arrangements in multy storey bldgs up to G+2 )surfaces complete all as specified and directed. ( coverage area 24-28 kg/sqm) |
| 13 | Supply only integral water proofing compound liquid admixture for mortar (Make - Fosroc , Conplast WL) complete all as specified and directed. |
| 14 | M &L for 10 to 12mm smart care ready mix repair plaster is a specially designed ready to use cement based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering (as per manufacture instructions) over interior wall surfaces complete all as specified and directed. (coverage area 24-28 kg/sqm specified . |
| 15 | M &L for 8 mm smart care ready mix repair plaster is a specially designed ready to use cement based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering (as per manufacture instructions) over Ceiling surfaces complete all as specified and directed ( including necessary arrangements in multy storey bldgs up to G+2 ). |
| 16 | M&L for preparation of new plastered or unplastered surfaces of wall, concrete surfaces, and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. |
| 17 | M&L for preparation of complete removal of existing treatment or unplastered surfaces of wall, concrete surfaces, and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. |
| 18 | M&L for two coats of oil bound distemper over a coat of average 2 mm thick putty on new plastered wall surfaces including preparation complete all as specified and directed. |
| 19 | M&L for applying two coats of oil bound distemper with roller on old decorated wall surfaces over 1 mm thick white putty including complete removal of existing treatment with mechanical complete all as specified and directed. |
| 20 | Material and labour for preparation of new steel or iron surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 21 | M&L for applying three coats of white wash on ceiling including preparation of new plastered or un-plastered surfaces, complete all as specified and directed. |
| 22 | M&L for washing rubbing down and stoping of distempred and pointed surfaces for applying two coats of white wash on ceiling including preparation of old plastered or un-plastered surfaces, complete all as specified and directed. |
| 23 | M&L for complete removal of existing treatment with mechanical device of old plastered surfaces of wall and applying two coat of white wash (match with new surface) complete all as specified and directed. |
| 24 | M & L cutting holes into or through brick wall built in cement mortar superfacial area not exc 150 Sqm cm and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-0 as required complete all as specified and directed. |
| 25 | S&F mild steel joist channel angle or tee sections fixed independently with out connecting plates etc of grade Fe-410-W (Gde E-250 quality B) complete all as specified and directed. |
| 26 | Removing or dismantling of damage / cracked/ concrete /loose concrete / plaster of celing/ wall/ chajja/ facia to expose the sound and hard concrete using a suitable mechanical device or by hammer and chisels etc complete all as specified & directed. |
| 27 | M&L for providing and applying on beam, col, ceilings surface by one part alkaline based material with corrosion inhibitors and dispersing agents for exposed steel surface after cleaning to loose scale or oxidized chips from bars, having bulk density 1.25. The material to be applied to the rusted metal with brush for complete wetting of rusted metal surface and allowed to react for 16-24 hours. After 24 hours, a white layer will appear which will protect further corrosion of metal / steel after about 5-7 days, before applying protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth etc to make surface dust free complete all as specified and directed. |
| 28 | M & L for applying bonding agent for bonding old to new concrete surface likes chajja/ beams/ celings/ columns/ facia etc by high performance modified Styrene- Butadiene Rubber ( SBR ) base binder . Applying of binder is as 10 sqm/ per litr ( including necessary arrangements in multy storey bldgs up to G+2 ) etc complete all as specified & directed. |
| 29 | M & L for applying 30 mm thick ( average ) polymer modified repair mortar for repair of RCC members likes beams, columns, chajja , facia , mortar having good compressive strength should not less than 30 Mpa and shrinkage resistance, mixing as per manufacture instruction etc ( including necessary arrangements in multy storey bldgs up to G+2 ) complete all as specified & directed. |
| 30 | S&F galvanised welded steel wire fabric as extra reionforcement to RCC members like ceilings, chajja’s, beams, columns parapet walls, waste slab etc including all cutting and waste (wt not exc 4.00 kg/Sqm) complete all as specified and directed. |
| 31 | M & L for applying 15 mm thick ( average ) smart care repair mortar ready to use single component polymer modified repair mortar for repair of RCC members ceiling stair case and wall mortar having good strength and shrinkage resistance use as per per manufactue instructions etc complete all as specified & directed. |
| 32 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed. |
| 33 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. |
| 34 | M&L No skid ceramic tiles 7 to 8 mm thick (square/rectangular) coloured tiles area of each tile exc 0.18 sqm not exc. 0.38 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and directed.(toilet,bath,kitchen, passage floor) |
| 35 | All as per Item No 34 above but in skirting over 10mm thick rendering in CM 1:4 |
| 36 | M&L for coloured glazed ceramic tiles in vertical surface 300 x 450 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match tiles including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed . |
| 37 | M&L non skid ceramic coloured tiles (1st quality/ premium quality) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exc. 0.18 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and directed. |
| 38 | M& L for PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection ( 75 mm thick ) laying in alternate bays finished even and smooth without using extra cement plinth protection shall be laid to alternate bay system each bay shall exceed 3m in lentgth 12mm wide and 75mm deep joint sall be filed with hot blown bitumen 85/25 and sand complete all as specified and directed. |
| 39 | S & F in repairs 15 mm bore chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 40 | S & F in repair 15 mm bore chromium plated long body bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 41 | S&F in repair 15 mm bore fancy type CP Stop valve / angle valve screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed. |
| 42 | S&F in repair sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed |
| 43 | S&F in repair 15 mm bore 3 in one wall mixer with Shower arrangement with connecting legs & Wall flanges complete all as specified and directed. |
| 44 | S&F 15mm bore Basin mixture for mixing hot and cold water , chromium plated with CP flange screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed. |
| 45 | S&F 15mm bore Sink mixture for mixing hot and cold water , chromium plated with CP flange screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed. |
| 46 | S&F in repairs 10 ltrs capacity PVC flushing cistern low level (white) with inlet ball valve and handle including flush pipe, brackets, rubber bush, washers dual flush etc complete all as specified and directed. |
| 47 | S&F in repair PVC connection 15mm size with PTMT nuts, 600 mm long complete all as specified and directed. |
| 48 | S&F in repairs fancy Vitreous china wash basin white flat back size 550 x 400mm incl waste coupling and waste pipe chain plug brackets complete all as specified and directed. . |
| 49 | S&F in repair PVC Bath cabinet mirror (single door) and fixed to chromium plated brass screw and cup washers complete all as specified and directed. |
| 50 | S&F in repairs kitchen sink with drainage board made of stainless steel 1mm thick with plugs, washers incl bedding in CM 1:4 to dwarf wall or including cast iron cantilever brackets and connecting union to pipe, overall size 915mm x 460 mm bowl size 410mm x 330mm x 160 mm and waste coupling and waste pipe etc complete all as specified and directed. |
| 51 | S&F in repairs plate rack of stainless steel , 1mm thick for kitchen or labotary, overall size 750x900x250 mm ,fixed with plugs and washers on wall all as specified and directed. |
| 52 | S & F in repair tubular towel rail 60 cm length of stainless steel 20 mm Dia with brackets type fixed with and including chromium plated brass screws, all neceesary fitting and wooden/plastic cleats complete all as specified and directed. |
| 53 | S & F in repairs CP shower rose 125mm dia alongwith shower min 600 long arm complete all as specified and directed. |
| 54 | S&F in repair Grating square/round 150 mm size of PTMT (Minimum weight 100gms) without hole /with waste hole complete all as spd and dir |
| 55 | S&F in repairs vitreous China squatting pan (Orissa pattern), white, of size 580x440mm white, along with integral foot rests including cast iron Trap 'P' or 'S' 100 mm dia, 32mm dia flush pipe, lime concrete bedding inlcuding taking out of old WC pan, old lime concrete bedding, unserviceable connections etc connecting up new and making good disturbe portion complete all as specified and directed by the Engineer-in-charge |
| 56 | S&F 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed. |
| 57 | S & F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as spd and dir. |
| 58 | S&F in repair 500 ltrs capacity rotational moulded polyethylene water storage tank double layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed. |
| 59 | Disconnecting existing water storage tanks 500 ltrs to 1000 ltrs capacity, setting aside (for lowering if required) for repair,cleaning ,etc and hosting if required reconnecting and refixing in position including cleaning, removing all scale dirt etc form tanks and from mouths of circulating pipe, repalcement old tank nipple, unions, stop cock, tank cover etc complete all as specified and as directed. |
| 60 | Taking up or down 15mm bore steel tubing and connection complete all as specified and directed. |
| 61 | All as per item No above but 20mm bore |
| 62 | S & F 16 mm outer diameter of CPVC brass elbow fixing to CPVC pipes any location complete all as specified. |
| 63 | S & F 16 mm outer diameter of CPVC brass tee fixing to CPVC pipes any location complete all as specified. |
| 64 | S & F 16mm to 20mm male Brass Threaded Adaptor (MTA/ MBTA) ) pipes any location complete all as specified. |
| 65 | Supplying and laying 16 mm outer diameter of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 66 | S&F 20mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 67 | Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth etc brick wall complete all as specified and directed. |
| 68 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks and clamps etc. |
| 69 | S & F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall and incl Stack clamps 1mtr centre to centre out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and directed. |
| 70 | S & F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to laid in tranches etc complete all as specified and as directed. |
| 71 | S & F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including all necessary fittings and fixing of 100Cm/centre to centre clamps out of 50 mm by 5 mm flat iron fixed with suitable bolt / screws securing etc complete all as specified and as directed.. |
| 72 | S & F 75mm bore PVC(SWR) HDPE high density polyethylene pipes single socketed in any length with rubber ring joints fixed to laid in tranches etc complete all as specified and as directed.. |
| 73 | S & F 110 mm bore PVC (SWR) pipes bends of any radius complete all as specified & directed. |
| 74 | S&F 110 mm bore PVC (SWR) pipes single T with access door of any radius complete all as specified & directed. |
| 75 | S & F 110 mm bore PVC (SWR) pipes cowl complete all as specified & directed. |
| 76 | S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified & directed. |
| 77 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed. |
| 78 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed. |
| 79 | M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65X100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madeetc complete all as specified and directed. |
| 80 | M&L for Factory made WPC (Wood Polymer Composite) Double Rebated frame of solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madeetc complete all as specified and directed. |
| 81 | M&L for Factory made WPC (Wood Polymer Composite) Single Rebated frame of solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45x85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madeetc complete all as specified and directed. |
| 82 | S&F for factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and including fixing with 100mm long stainless steel butt hinges -04Nos with necessary full body threaded star headed counter sunk S.S screws, complete all as per specified and directed. |
| 83 | S&F 35 mm thick Factory made solid panel PVC wire gauzed door shutter 35 mm thick i.e. panel will be of wire gauze of wood grain printed PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet used instead of plain colour PVC sheet & 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm used beading of exposed portion of PVC sheet beading channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing including fixing with 100mm long stainless steel butt hinges -04 Nos complete all as specified and directed. |
| 84 | S & F in repair Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) decorative Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cum manufactured by Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws and all required frame as per site requirement. Material test certificate and authentication should be compulsory provided by the manufacturing company: For Kitchen Doors and Cabinets. Complete all as specified and directed |
| 85 | S&F 100 mm long stainless steel hinges complete all as specified and directed. |
| 86 | S&F for 30mm witdth of flaps (when open) continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed. |
| 87 | S&F 150 mm long stainless steel handles, fabricated type, complete all as specified and directed. |
| 88 | S&F 150 mm long stainless steel, barrel tower bolts of complete all as specified and directed. |
| 89 | S & F Floor door stopper of stainless steel body and tongue, anodised,with hard drawn steel spring, fixed in floor overall 140mm length of cover plate complete all as specified and as directed. |
| 90 | S&F 300 mm long stainless steel, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts complete all as specified and directed. |
| 91 | S & F MS Helical Door springs 300mm long ordinary rat tail pattern including roller and roller palate complete all as specified and as directed. |
| 92 | S&F 125mm long stainless steel Hasp and Staple, safety type including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 93 | M&L cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in bed blocks for fixing hold fasts etc. complete all as specified and directed. |
| 94 | S & F stainless steel 40mm dia decorative knob for kitchen cup board complete all as specified and directed. |
| 95 | S & F Brass magnet catcher suitable for CB/cabinet shutter complete all as specified and directed. |
| 96 | S & F in repair windows made of pre-painted steel fabricated from roll formed section made of Galvanized steel colour/ coated/powder coated ( Base steel as per IS 513 \\"D\\" quality, galvanized as per IS 277 with zinc of 120 gms/sqm) with total coated thickness of 0.60mm. Sections should be with primer coat of epoxy primer of 5-7 microns and powder coated with pure polyester powder up to 50-60 microns thick. Section for frame should be of 72mm x 50mm. Section for mullion should be of 12mm x 12mm and section for fly mesh should be of 47mm x 20mm, section for fixed glass bead should be of 12mm x 12mm and section for fly mesh should be for 40mm x 20mm. Each glazed shutter should be provided with SS pivot hinges 1 set sec color handle and stay. Each glazed shutter and fixed glass portions should be provided with a glass of 5mm plain float glass. Mess shutter should be provided with stainless steel 32 gauge fly mesh of 304 grades with 144 holes per sq. In window should be provided handle, tower bolt with grill made of 10 sq MS bars welded to at 150mm center to center, 6mm x 12mm flat. Total grill unit should be powder coated and fixed to window frame with screws including necessary fixing legs andconcrete work complete all as specified and directed. |
| 97 | S & F in repair windows made of pre-painted steel fabricated ventilator fabricated from roll formed section made of Galvanized steel colour/ coated/powder coated ( Base steel as per IS 513 \\"D\\" quality, galvanized as per IS 277 with zinc of 120 gm/sqm) with total coated thickness of 0.60mm. Sections should be with primer coat of epoxy primer of 5-7 microns, or powder coated with pure polyester powder up to 50-60 microns thick. Section for frame should be of 72mm x 50mm. Section for mullion should be of 72mm x 50mm. section for shutter frame mesh should be of 47mm x 20mm, Section for fixed glass bead should be of 12mm x 12mm and section for fly mesh should be for 40mm x 20mm. Each glazed shutter should be provided with SS pivot hinges-1 set sec color handle and stay. Each glazed shutter and fixed glass portions should be provided with a glass of 5mm plain float glass. Mesh shutter should be provided with stainless steel 32 gauge fly mesh of 304 grades with 144 holes per sq. In window should be provided with grill made of 10 sq MS bars welded to at 150mm center to center, 6mm x 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws including necessary fixing ledg and concrete work complete all as specified and directed. |
| 98 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm dia fixed with stainless steel wire staples complete all as specified and as directed. |
| 99 | S&F in repairs stainless steel curtain rods, 20mm internal diameter including decoratine type brackets and SS dcorative cap including fixing arrangement with drilling holes in walls, brackets etc complete all as specified and directed. |
| 100 | M&L 20mm thick black granite (of any type) work (table rubbed and polished) in steps jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of stone including rounding and moulding of edge and making hole for cooking gas pipe complete all as specified and as directed. |
| 101 | M&L Machine cut pre polished kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including 20mm thick screed bed CM (1:6) complete all as specified and directed. |
| 102 | M&L single piece Machine cut pre polished kota stone 20-25 mm thick as in riser of step, skirting,dado and pillar etc. laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing laid over and including 15mm thick rendering CM (1:4) complete all as specified and directed. |
| 103 | M&L for preparation of old painted steel surfaces & applying one coat of synthetic enamel paint on steel surface of any description over 10 cm in width or girth complete all as specified and as directed. |
| 104 | Demolition of cement concrete(unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed. |
| 105 | M&L for Rendering 10mm thick in CM 1:3 using water proofing compound as per manufacture instruction finished even and smooth without using extra cement and curved adqutely and after drying apply two coats of Brushbond Aquaprotect of Fosroc or equivalent both on floor and walls of sunken poriton and tested complete. |
| 106 | M & L for broken bricks loose filling with aggregates of gauge 40 to 80mm in sunken protion complete all as spd and dir by Engr-in-charge. |
| 107 | PCC 1:5:10 E-2 (using 40 mm graded crushed stone aggregate) as in sunken floo fair even and smooth without using extra cement all as specified. |
| 108 | S & F in repair 75mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed. |
| 109 | Boring holes through cooking platform lining for pipes ,etc n'exc 50mm dia and making good complete all as spd and dir by Engr-in-charge. |
| 110 | Dismantling of wrought iron of mild steel work of any description not otherwise provided |
| 111 | S & F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0.complete all as specified and directed. |
| 112 | Removing building materials etc. (other than spoil payable under items 03028 to 03031 in Section-3-Earthwork) to a distance of 1000m or under qty to be speciifed including loading, unloading and stacking at the destination. |
| 113 | M&L for treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors. |
| 114 | Providing Acrylic plastic number plate of size 200mmX 200mm X 3mm and writing Qtr No. size of letter height 10 to 15 cm in any style (bold/italic) and fixed to wall with screws complete all as specified & directed. |
| 115 | M& L writing/ letters to mention building details in displays card over will surface, the dimension of display card should be 90cmx 60 cm, location as decided by Engr-in- charge on the wall of each building. The display card shall indicate the following details by applying two coat of enamel painting as approved colour as specified and directed.BLDG NO/VINTAGE : (BLDG NO & YEAR)PERIODICAL MAINT DONE ON : (MONTH 2024/25)LAST SPL REPAIR UNDER TAKEN ON : (MONTH & YEAR)ADDN/ALTN/ ANY OTHER TYPE :OF WK CARRIED OUT WITH DATE |
| 116 | Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth for foundation, manholes, etc n.exc 10 Sqm plan and getting out in soft/loose soil complete all as specified and directed. |
| 117 | Returning filling including spreading,levelling,watering and well ramming in layers n. exc 25 cm thick complete all as specified & directed. |
| 118 | Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar including concrete bedding and haunching complete all as specified and directed for 150mm bore of pipe |
| 119 | Supply,laying and jointed 150 mm nominal bore dia DWC( double wall corrugated),socketed and sewage pipes having 6.00 M length,conforming to IS 16098 (Part-2) of SN-4 stiffiness with and including necessary jointing materials etc complete all as specified and directed . |
| 120 | M&L for providing pre-cast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in cover (for manholes and drains) including necessary form work set in CM 1:6 with and including demolition complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately) |
| 121 | M & L for mild steel TMT bar 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally, binding wire (0.90mm dia annealed) complete all as specifed and difrected. |
| 122 | Cutting into existing manholes for connecting new drain pipe, making good to pipe and rendering cutting out benching for and forming branch channel (1/2 round 3/4 Sec) in cement conc (1:2:4) type B-1smooth finished and reforming benching as reqd for 150mm bore pipe. |
| 123 | M&L for 75 mm thick Cement concrete type D-2 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing finishing surface even and rough using broom finish complete all as specified and directed. |
| 124 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 125 | Demolition of stone slab and tile of any description or thickness in floor aprons etc laid & bedded in any mortar. complete all as specified and directed. |
| 126 | Taking down carefully existing unserviceable copper / aluminum point wiring of any description & in any position with and ncluding taking out existing unserviceable conduits or battens of any description with sunken boxes/junction boxes and all fitting, accessories & fixtures such as switches, ceiling roses, pendants, regulators, socket, light fittings, lamp holders etc but excluding tube light fittings and making good the disturbed surface of walls, floors, ceiling etc to match with the existing surfaces complete all as specified and directed. |
| 127 | M&L point wiring with 1.5 sqmm multi stranded copper conductor 1100 volts grade FRLSH PVC insulated unsheathed cable with proper colour coding drawn in including PVC concealed conduit not less than 20 mm dia with all accessories and FRLSH PVC insulated 1.5 Sqmm multi standard unsheathed copper wire for continues earth, including cutting and chasing of wall surface for laying PVC conduit and modular sunken box of suitable module as per site requirement not less than 1.6mm thick and connecting earth and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles. Note:- Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit is not feasible at no extra cost for the following :- One light /fan point controlled by one switch |
| 128 | One 5 pin socket outlet 5 Amps on same board |
| 129 | One 5 pin socket outlet 5 Amps on independent board |
| 130 | One bell/buzzer point controlled by one push button on the same board with other switches or independent |
| 131 | One light point controlled by two 2 way switches with cables 1.5 sqmm size. |
| 132 | One TV socket point wiring with cables RG-6 Coaxial cable |
| 133 | All as per item No.127 here in before but with FRLSH cable size 4 Sq mm for one 5 pin 15/16 Amps socket out let on independent board / AC box and multistrand insulated copper earth continuity conductor of size 4 sqmm all as specified and directed by Engr-in-Charge. |
| 134 | Supply and fixing modular TV coaxial socket outlet fixed in 1 M box comprising of flush metal box, inner plate and outer cover complete all as specified. |
| 135 | Supply and fixing modular switch piano single pole, one way 6 Amps 1 module, complete all as specified and directed. |
| 136 | Supply and fixing modular switch piano single pole, two way 6 Amps 1 module, complete all as specified and directed. |
| 137 | Supply and fixing modular switch piano flush type 16 Amps single pole one way, one module, complete all as specified and directed. |
| 138 | Supply and fixing modular socket outlet 2/3 pin 6 Amps combined 2 module, complete all as specified and directed. |
| 139 | Supply and fixing modular socket multipurpose 3 pin 6/16 Amps combined 2 module, complete all as specified and directed. |
| 140 | Supply and fixing modular step type, 1/2 module electronic fan regulator heavy duty 120watts 240 volts. , complete all as specified and directed. |
| 141 | Supply and fixing Modular Bell push 6A 1 module pole, one way, complete all as specified and directed. |
| 142 | Supply and fixing call bell, Ding Dong type, 230 volts AC single pole complete all as directed. |
| 143 | Supplying & fixing for ceiling rose PVC Polycarbonate isolated body 62.5 x 25 mm, three terminals, complete all as specified & directed. |
| 144 | Supply and fixing modular cover plate with metal frame (inner and outer) 1 module for mounting switch and sockets all as specified and as directed. |
| 145 | Supply and fixing modular cover plate with metal frame (inner and outer) 2 module for mounting switch and sockets all as specified and as directed. |
| 146 | Supply and fixing modular cover plate with metal frame (inner and outer) 3 module for mounting switch and sockets all as specified and as directed. |
| 147 | Supply and fixing modular cover plate with metal frame (inner and outer) 4 module for mounting switch and sockets all as specified and as directed. |
| 148 | Supply and fixing modular cover plate with metal frame (inner and outer) 8 module for mounting switch and sockets all as specified and as directed. |
| 149 | Supply and fixing blank spacer plate for single module. |
| 150 | S&F 20W Inverter LED batten with square profile and polycarbonate channel. Lithium Ion battery with charging time 8hours-10 hours and back up time upto 4 hours including connecting up with three core flexible copper conductor cable of suitable size form ceiling rose complete all as specified and directed. |
| 151 | S&F 20W LED batten surface / wall mounted with specially designed powder coated aluminium housing, high optically efficient polycarbonate diffuser, in built electronic driver duly pre-wired upto terminal block and fixing arrangements for fixing the light fitting complete all as specified and directed. |
| 152 | S&F 10W LED batten surface / wall mounted with specially designed powder coated aluminium housing, high optically efficient polycarbonate diffuser, in built electronic driver duly pre-wired upto terminal block and fixing arrangements for fixing the light fitting complete all as specified and directed. |
| 153 | S&F bulk head, luminaire made of die cast aluminium housing 10 watt LED, internally prewired with and including premium quality diffuser for glarefree light and easy to install snap fit installer complete with all accessories and connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.50 sqmm and fixing arrangements for fixing the light fitting complete all as specified and directed. |
| 154 | Supply and fixing in replacement LED building security light fitting 35 Watt 230 V AC out-door type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, fixed to pole or wall of building with and including suitable Bracket made out of 25 mm dia GI light grade pipe, 1.00 m long bent to shape by cutting & welding as required & directed and fixed with two Nos of FI clamps 35x6 mm to be tightened with suitable size of bolts, nut and washers and including painted with two coat of aluminium paint over a coat of red oxide primer, and including connecting the fitting to electric source with & including twin twisted copper flexible wire of size 0.75 sqmm three core with suitable size flexible PVC conduit including all accessories and fixing arrangements for fixing the light fitting and writing the date of fixing on security light with permt marker complete all as specified and directed. Note :- The period of defects liability shall be 02 years from the date of installation of security light. |
| 155 | Supply and fix exhaust fan (copper winding), steel body AC single phase, 230 V of size 300 mm sweep with blades, and frame and louvers taking down existing fan in and deposit to AGE E/M store complete all as specified and directed. |
| 156 | Supply and fix exhaust fan made of sturdy Engineering platic complete with louvers shutter, voltage 230 V, 50 Hz, RPM 1200, copper winding of sweep 300 mm taking down existing fan in and deposit to AGE E/M store complete all as specified and directed. |
| 157 | Taking down fan, sealing cable end, dismantling blades and removing fan and blades deposit to AGE E/M yard store complete all as specified and directed. |
| 158 | Supply and fix in replacement of Intelligent BLDC (Brush Less Direct Current) Energy Saving Ceiling fan (copper winding) of size 1400mm sweep with smart remote for easy operation with 5 speed setting and smart features like boost mode and timer functionality for 2, 4,6 and 8 hours, 230 Volts, 50Hz, power consumtion is less than 35 watt, 5 Star rated, noiseless motor operation, inverter stabilization technology, 370 RPM, 245 CFM alongwith necessary accessorie like anti suicide down road 12\\", canopy, blades, BLDC motor, hanging clip etc and 03 year On Site warranty including writting the MES Number with synthetic enamel paint, including electrically connecting from fan to ceiling rose inlcluding suitable size flexible PVC conduit, complete all as specified and as directed. |
| 159 | Supply and fixing Geyser of 25 Ltrs capacity, 5 star rating AC single phase, 230 volts, Stainless Steel inner tank including connection with three core multistranded copper conductor of size 2.5 sqmm including necessary fixing arrangement i.e anchor nut, bolt, washer,CP pipe connection, grouting and making good to disturbed surface and cleaning of the area incl taking down existing geyser and deposit to AGE E/M store complete all as specified and as directed. |
| 160 | Disconnecting & taking up or down existing unserviceable sub main wiring of copper / aluminium conductor with two run of single core cable with one run of single core earth conductor cable of any description, any size and in any position including taking out existing unserviceable conducits or battens of any description and making good the disturbed surfaces to the existing surfaces complete all as specified and directed. |
| 161 | M&L for sub main wiring using two 2x6 sqmm single core FRLSH PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) as required dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 1x 6 sqmm as earth continuity conductor connected to earth dolly complete all as specified and directed. (NOTE : Two run of single core PVC cable with one run of earth conductor and conduit /batten shall be measured as one unit.) |
| 162 | M&L for sub main wiring using two 2x4 sqmm single core FRLSH PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) as required dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 1x 4 sqmm as earth continuity conductor connected to earth dolly complete all as specified and directed. (NOTE : Two run of single core PVC cable with one run of earth conductor and conduit /batten shall be measured as one unit.) |
| 163 | Supply, fixing, connecting and testing sheet metal single pole and neutral enclosure with metal clad (two pin and earth) plug top and socket complete with and including one No MCB ('C' series), SP, 20 Amps, 240 volts, having breaking capacity 10 KA complete all as specified and directed. |
| 164 | Supply & fix sheet metal enclosure MCB distribution board Single pole & neutral 240 volts 12 way double door complete with appropriate size bus bar and neutral link including taking down all as specified and directed. |
| 165 | Supply and fixing in repair MCB SP 6 to 32 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed. |
| 166 | Supply and fixing in repair MCB SPN 40 to 63 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed. |
| 167 | M&L in replacement for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level ) with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized steel wire 4mm dia as earth lead soldered and riveted to earth plate by means of nuts, bolts, check nuts & washers, of galvanized iron or steel with connected to test point and testing on completion including 15mm GI light grade pipe for earth lead protection from earth point to earth plate, including provn adequate quantity of charcoal dust mixed with 35 % common salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth plate with 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire mesh with and including all necessary excavation & earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c Both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and as directed. NOTES:-(i) On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor. |
| 168 | Taking down, refixing and connecting electric meters 10-60 amps in meter panel box complete as specified and direced. |
| 169 | S&F in repair 4 pair telephone cable 0.5 sqmm copper of diameter and is insulated with a special grade polyethylene compound on the latest state of the art extruders. The cores are twisted together with a uniform lay from meter to CIU units complete all as specified and directed. |
| 170 | S&F rigid non metallic PVC conduit 20 mm dia exclusive of boex (junction / terminal) but inclusive of all trees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed. |
| 171 | Supply, fixing and connecting in repair for electric circuilts for size of 1.0 sqmm copper FRLS wire for inverter in existing conduit/casiing caping complete all as specified and directed. |
| 172 | Supply, installation, testing and commissioning of indoor type wall mounting size min (830 x 1100 x 245 mm), polycarbonate CPRI approved OEM made meter panel suitable for 06 (six) single phase meter. The panel shall be made of modular POLYCARBONATE THERMOPLASTIC ENCLOSURES which should be UV resistance in accordance with IEC 61439-1, clause 10.2.4. the panel type wall mounted on mounting structure RAL 7016. The meter panel should be anti -acid & anti corrosive and fully transparent door for meter vision . Degree of protection against mechanical load should be IK08 (5 Joule) in accordance with IEC 62262. The manufacturer of panel shall submit a copy of CPRI test report in polycarbonate only degree in ingress protection IP65 in accordance with IEC 60529. The gasket should be internally embedded made of polyurethane and enclosure make. the manufacturer of board / panel shall submit a copy of type test report of a board made out of polycarbonate thermoplastic panel in accordinace with IEC 60439-1 complete all as specified and directed.Note :- Re-fixed the engergy meter in new meter cabinet including all necessary electrical connection. General specification & electrical parameter. 6 METER DB-2 Ref No.2236/2023 (REV-1). Type of panel :- Thermoplastic polycarbonate panel size - 830 x 1100 x 245 mm, Degree of protectio - IP65(EN60 529) System Voltage : 415 V, 50 Hz, 4 wire +E Installation : Indoor Floor mounting, Cable Entry :- Incomming /outgoing from bottom. Finiesh shade :- Enclosure & Accessories : RAL 7035 Mounting structure : RAL 7016, Income:125A, FP 25mA MCCB-01 Nos, outgoing : 40A DP 10 kA MCB - 6 Nos (5-32) A, 1 Phase PREPAID ENERGY METER -6 Nos (Provision only), Terminal : 10 SQMM TERMINAL BLOCK - 12 Nos, 10SQMM TERMINAL BLOCK - 06 Nos, RECOMMENDED CABLE :- Incoming-I/C -4CX35/50 Sqmm cable (125A), O/C - 3CX6 Sqmm cable. Make - Hensel / Rittal/ Schnieder. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
